#define RXD_W7_RESERVED FIELD32(0xffffffff)
/*
- * Macro's for converting txpower from EEPROM to mac80211 value
+ * Macros for converting txpower from EEPROM to mac80211 value
* and from mac80211 value to register value.
* NOTE: Logics in rt2400pci for txpower are reversed
* compared to the other rt2x00 drivers. A higher txpower
#define RXD_W10_DROP FIELD32(0x00000001)
/*
- * Macro's for converting txpower from EEPROM to mac80211 value
+ * Macros for converting txpower from EEPROM to mac80211 value
* and from mac80211 value to register value.
*/
#define MIN_TXPOWER 0
#define RXD_W3_EIV FIELD32(0xffffffff)
/*
- * Macro's for converting txpower from EEPROM to mac80211 value
+ * Macros for converting txpower from EEPROM to mac80211 value
* and from mac80211 value to register value.
*/
#define MIN_TXPOWER 0
/*
* Before the radio can be enabled, the device first has
* to be woken up. After that it needs a bit of time
- * to be fully awake and the radio can be enabled.
+ * to be fully awake and then the radio can be enabled.
*/
rt2800usb_set_state(rt2x00dev, STATE_AWAKE);
msleep(1);
break;
case STATE_RADIO_OFF:
/*
- * After the radio has been disablee, the device should
+ * After the radio has been disabled, the device should
* be put to sleep for powersaving.
*/
rt2800usb_disable_radio(rt2x00dev);
#define RXWI_W3_SNR1 FIELD32(0x0000ff00)
/*
- * Macro's for converting txpower from EEPROM to mac80211 value
+ * Macros for converting txpower from EEPROM to mac80211 value
* and from mac80211 value to register value.
*/
#define MIN_G_TXPOWER 0
struct antenna_setup active;
/*
- * RSSI information for the different antenna's.
+ * RSSI information for the different antennas.
* These statistics are used to determine when
* to switch antenna when using software diversity.
*
* The structure stored in here depends on the
* system bus (PCI or USB).
* When accessing this variable, the rt2x00dev_{pci,usb}
- * macro's should be used for correct typecasting.
+ * macros should be used for correct typecasting.
*/
struct device *dev;
/*
* Failsafe: Make sure we are not sending the
* ANTENNA_SW_DIVERSITY state to the driver.
- * If that happes fallback to hardware default,
+ * If that happens, fallback to hardware defaults,
* or our own default.
* The calls to rt2x00lib_config_antenna_check()
* might have caused that we restore back to the already
/* Pull buffer to correct size */
skb_pull(skb, txdesc->iv_len);
- /* IV/EIV data has officially be stripped */
+ /* IV/EIV data has officially been stripped */
skbdesc->flags |= SKBDESC_IV_STRIPPED;
}
/*
* During the last period we have sampled the RSSI
- * from both antenna's. It now is time to determine
+ * from both antennas. It now is time to determine
* which antenna demonstrated the best performance.
* When we are already on the antenna with the best
* performance, then there really is nothing for us
int status;
/*
- * Mac80211 might be calling this function while we are trying
+ * mac80211 might be calling this function while we are trying
* to remove the device or perhaps suspending it.
*/
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
int update_bssid = 0;
/*
- * Mac80211 might be calling this function while we are trying
+ * mac80211 might be calling this function while we are trying
* to remove the device or perhaps suspending it.
*/
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
#include <linux/prefetch.h>
/**
- * DOC: Entrie frame size
+ * DOC: Entry frame size
*
* Ralink PCI devices demand the Frame size to be a multiple of 128 bytes,
* for USB devices this restriction does not apply, but the value of
/**
* DOC: Number of entries per queue
*
- * Under normal load without fragmentation 12 entries are sufficient
+ * Under normal load without fragmentation, 12 entries are sufficient
* without the queue being filled up to the maximum. When using fragmentation
- * and the queue threshold code we need to add some additional margins to
+ * and the queue threshold code, we need to add some additional margins to
* make sure the queue will never (or only under extreme load) fill up
* completely.
- * Since we don't use preallocated DMA having a large number of queue entries
- * will have only minimal impact on the memory requirements for the queue.
+ * Since we don't use preallocated DMA, having a large number of queue entries
+ * will have minimal impact on the memory requirements for the queue.
*/
#define RX_ENTRIES 24
#define TX_ENTRIES 24
#define is_valid_mask(x) is_power_of_two(1LU + (x) + low_bit_mask(x))
/*
- * Macro's to find first set bit in a variable.
- * These macro's behaves the same as the __ffs() function with
+ * Macros to find first set bit in a variable.
+ * These macros behave the same as the __ffs() functions but
* the most important difference that this is done during
* compile-time rather then run-time.
*/
}
/*
- * Determine number of antenna's.
+ * Determine number of antennas.
*/
if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_NUM) == 2)
__set_bit(CONFIG_DOUBLE_ANTENNA, &rt2x00dev->flags);
#define RXD_W15_RESERVED FIELD32(0xffffffff)
/*
- * Macro's for converting txpower from EEPROM to mac80211 value
+ * Macros for converting txpower from EEPROM to mac80211 value
* and from mac80211 value to register value.
*/
#define MIN_TXPOWER 0
/*
* EEPROM antenna.
- * ANTENNA_NUM: Number of antenna's.
+ * ANTENNA_NUM: Number of antennas.
* TX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B.
* RX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B.
* FRAME_TYPE: 0: DPDT , 1: SPDT , noted this bit is valid for g only.
#define RXD_W5_RESERVED FIELD32(0xffffffff)
/*
- * Macro's for converting txpower from EEPROM to mac80211 value
+ * Macros for converting txpower from EEPROM to mac80211 value
* and from mac80211 value to register value.
*/
#define MIN_TXPOWER 0
projects / linux-flexiantxendom0-natty.git / commitdiff