* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (dme1737) Minor cleanups
hwmon: (dme1737) Add support for in7 for SCH5127
hwmon: (emc1403) Add EMC1423 support
hwmon: (w83627hf) Document W83627THF voltage pin mapping
hwmon: (w83793) Drop useless mutex
hwmon: (fschmd) Drop useless mutex
hwmon: (w83781d) Use pr_fmt and pr_<level>
hwmon: (pc87427) Use pr_fmt and pr_<level>
hwmon: (pc87360) Use pr_fmt and pr_<level>
hwmon: (lm78) Use pr_fmt and pr_<level>
hwmon: (it87) Use pr_fmt and pr_<level>
hwmon: Schedule the removal of the old intrusion detection interfaces
hwmon: (w83793) Implement the standard intrusion detection interface
hwmon: (w83792d) Implement the standard intrusion detection interface
hwmon: (adm9240) Implement the standard intrusion detection interface
hwmon: (via686a) Initialize fan_div values
hwmon: (w83795) Silent false warning from gcc
hwmon: (ads7828) Update email contact details
Who: Tejun Heo <tj@kernel.org>
----------------------------
+
+What: Legacy, non-standard chassis intrusion detection interface.
+When: June 2011
+Why: The adm9240, w83792d and w83793 hardware monitoring drivers have
+ legacy interfaces for chassis intrusion detection. A standard
+ interface has been added to each driver, so the legacy interface
+ can be removed.
+Who: Jean Delvare <khali@linux-fr.org>
+
+----------------------------
The ADM9240 provides an internal open drain on this line, and may output
a 20 ms active low pulse to reset an external Chassis Intrusion latch.
-Clear the CI latch by writing value 1 to the sysfs chassis_clear file.
+Clear the CI latch by writing value 0 to the sysfs intrusion0_alarm file.
Alarm flags reported as 16-bit word
http://focus.ti.com/lit/ds/symlink/ads7828.pdf
Authors:
- Steve Hardy <steve@linuxrealtime.co.uk>
+ Steve Hardy <shardy@redhat.com>
Module Parameters
-----------------
This driver implements support for the hardware monitoring capabilities of the
SMSC DME1737 and Asus A8000 (which are the same), SMSC SCH5027, SCH311x,
and SCH5127 Super-I/O chips. These chips feature monitoring of 3 temp sensors
-temp[1-3] (2 remote diodes and 1 internal), 7 voltages in[0-6] (6 external and
+temp[1-3] (2 remote diodes and 1 internal), 8 voltages in[0-7] (7 external and
1 internal) and up to 6 fan speeds fan[1-6]. Additionally, the chips implement
up to 5 PWM outputs pwm[1-3,5-6] for controlling fan speeds both manually and
automatically.
in4: V1_IN 0V - 1.5V
in5: VTR (+3.3V standby) 0V - 4.38V
in6: Vbat (+3.0V) 0V - 4.38V
+ in7: Vtrip (+1.5V) 0V - 1.99V
Each voltage input has associated min and max limits which trigger an alarm
when crossed.
vrm RW Voltage regulator module version
number.
-in[0-6]_input RO Measured voltage in millivolts.
-in[0-6]_min RW Low limit for voltage input.
-in[0-6]_max RW High limit for voltage input.
-in[0-6]_alarm RO Voltage input alarm. Returns 1 if
+in[0-7]_input RO Measured voltage in millivolts.
+in[0-7]_min RW Low limit for voltage input.
+in[0-7]_max RW High limit for voltage input.
+in[0-7]_alarm RO Voltage input alarm. Returns 1 if
voltage input is or went outside the
associated min-max range, 0 otherwise.
pwm5 opt opt
fan6 opt opt
pwm6 opt opt
+in7 yes
The above sequence assumes a Super-I/O config space at 0x2e/0x2f, but
0x4e/0x4f is also possible.
+
+Voltage pin mapping
+-------------------
+
+Here is a summary of the voltage pin mapping for the W83627THF. This
+can be useful to convert data provided by board manufacturers into
+working libsensors configuration statements.
+
+ W83627THF |
+ Pin | Name | Register | Sysfs attribute
+-----------------------------------------------------
+ 100 | CPUVCORE | 20h | in0
+ 99 | VIN0 | 21h | in1
+ 98 | VIN1 | 22h | in2
+ 97 | VIN2 | 24h | in4
+ 114 | AVCC | 23h | in3
+ 61 | 5VSB | 50h (bank 5) | in7
+ 74 | VBAT | 51h (bank 5) | in8
+
+For other supported devices, you'll have to take the hard path and
+look up the information in the datasheet yourself (and then add it
+to this document please.)
* Chassis
If the case open alarm triggers, it will stay in this state unless cleared
- by any write to the sysfs file "chassis".
+ by writing 0 to the sysfs file "intrusion0_alarm".
* VID and VRM
The VRM version is detected automatically, don't modify the it unless you
will be called dme1737.
config SENSORS_EMC1403
- tristate "SMSC EMC1403 thermal sensor"
+ tristate "SMSC EMC1403/23 thermal sensor"
depends on I2C
help
- If you say yes here you get support for the SMSC EMC1403
+ If you say yes here you get support for the SMSC EMC1403/23
temperature monitoring chip.
Threshold values can be configured using sysfs.
* Alarms 16-bit map of active alarms
* Analog Out 0..1250 mV output
*
- * Chassis Intrusion: clear CI latch with 'echo 1 > chassis_clear'
+ * Chassis Intrusion: clear CI latch with 'echo 0 > intrusion0_alarm'
*
* Test hardware: Intel SE440BX-2 desktop motherboard --Grant
*
static DEVICE_ATTR(aout_output, S_IRUGO | S_IWUSR, show_aout, set_aout);
/* chassis_clear */
-static ssize_t chassis_clear(struct device *dev,
+static ssize_t chassis_clear_legacy(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
unsigned long val = simple_strtol(buf, NULL, 10);
+ dev_warn(dev, "Attribute chassis_clear is deprecated, "
+ "use intrusion0_alarm instead\n");
+
if (val == 1) {
i2c_smbus_write_byte_data(client,
ADM9240_REG_CHASSIS_CLEAR, 0x80);
}
return count;
}
-static DEVICE_ATTR(chassis_clear, S_IWUSR, NULL, chassis_clear);
+static DEVICE_ATTR(chassis_clear, S_IWUSR, NULL, chassis_clear_legacy);
+
+static ssize_t chassis_clear(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm9240_data *data = i2c_get_clientdata(client);
+ unsigned long val;
+
+ if (strict_strtoul(buf, 10, &val) || val != 0)
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+ i2c_smbus_write_byte_data(client, ADM9240_REG_CHASSIS_CLEAR, 0x80);
+ data->valid = 0; /* Force cache refresh */
+ mutex_unlock(&data->update_lock);
+ dev_dbg(&client->dev, "chassis intrusion latch cleared\n");
+
+ return count;
+}
+static SENSOR_DEVICE_ATTR(intrusion0_alarm, S_IRUGO | S_IWUSR, show_alarm,
+ chassis_clear, 12);
static struct attribute *adm9240_attributes[] = {
&sensor_dev_attr_in0_input.dev_attr.attr,
&dev_attr_alarms.attr,
&dev_attr_aout_output.attr,
&dev_attr_chassis_clear.attr,
+ &sensor_dev_attr_intrusion0_alarm.dev_attr.attr,
&dev_attr_cpu0_vid.attr,
NULL
};
This driver is based on the lm75 and other lm_sensors/hwmon drivers
- Written by Steve Hardy <steve@linuxrealtime.co.uk>
+ Written by Steve Hardy <shardy@redhat.com>
Datasheet available at: http://focus.ti.com/lit/ds/symlink/ads7828.pdf
i2c_del_driver(&ads7828_driver);
}
-MODULE_AUTHOR("Steve Hardy <steve@linuxrealtime.co.uk>");
+MODULE_AUTHOR("Steve Hardy <shardy@redhat.com>");
MODULE_DESCRIPTION("ADS7828 driver");
MODULE_LICENSE("GPL");
* in4 +12V
* in5 VTR (+3.3V stby)
* in6 Vbat
+ * in7 Vtrip (sch5127 only)
*
* --------------------------------------------------------------------- */
-/* Voltages (in) numbered 0-6 (ix) */
-#define DME1737_REG_IN(ix) ((ix) < 5 ? 0x20 + (ix) \
- : 0x94 + (ix))
+/* Voltages (in) numbered 0-7 (ix) */
+#define DME1737_REG_IN(ix) ((ix) < 5 ? 0x20 + (ix) : \
+ (ix) < 7 ? 0x94 + (ix) : \
+ 0x1f)
#define DME1737_REG_IN_MIN(ix) ((ix) < 5 ? 0x44 + (ix) * 2 \
: 0x91 + (ix) * 2)
#define DME1737_REG_IN_MAX(ix) ((ix) < 5 ? 0x45 + (ix) * 2 \
* IN_TEMP_LSB(1) = [temp3, temp1]
* IN_TEMP_LSB(2) = [in4, temp2]
* IN_TEMP_LSB(3) = [in3, in0]
- * IN_TEMP_LSB(4) = [in2, in1] */
+ * IN_TEMP_LSB(4) = [in2, in1]
+ * IN_TEMP_LSB(5) = [res, in7] */
#define DME1737_REG_IN_TEMP_LSB(ix) (0x84 + (ix))
-static const u8 DME1737_REG_IN_LSB[] = {3, 4, 4, 3, 2, 0, 0};
-static const u8 DME1737_REG_IN_LSB_SHL[] = {4, 4, 0, 0, 0, 0, 4};
+static const u8 DME1737_REG_IN_LSB[] = {3, 4, 4, 3, 2, 0, 0, 5};
+static const u8 DME1737_REG_IN_LSB_SHL[] = {4, 4, 0, 0, 0, 0, 4, 4};
static const u8 DME1737_REG_TEMP_LSB[] = {1, 2, 1};
static const u8 DME1737_REG_TEMP_LSB_SHL[] = {4, 4, 0};
#define DME1737_REG_ALARM1 0x41
#define DME1737_REG_ALARM2 0x42
#define DME1737_REG_ALARM3 0x83
-static const u8 DME1737_BIT_ALARM_IN[] = {0, 1, 2, 3, 8, 16, 17};
+static const u8 DME1737_BIT_ALARM_IN[] = {0, 1, 2, 3, 8, 16, 17, 18};
static const u8 DME1737_BIT_ALARM_TEMP[] = {4, 5, 6};
static const u8 DME1737_BIT_ALARM_FAN[] = {10, 11, 12, 13, 22, 23};
#define HAS_PWM_MIN (1 << 4) /* bit 4 */
#define HAS_FAN(ix) (1 << ((ix) + 5)) /* bits 5-10 */
#define HAS_PWM(ix) (1 << ((ix) + 11)) /* bits 11-16 */
+#define HAS_IN7 (1 << 17) /* bit 17 */
/* ---------------------------------------------------------------------
* Data structures and manipulation thereof
u32 has_features;
/* Register values */
- u16 in[7];
- u8 in_min[7];
- u8 in_max[7];
+ u16 in[8];
+ u8 in_min[8];
+ u8 in_max[8];
s16 temp[3];
s8 temp_min[3];
s8 temp_max[3];
static const int IN_NOMINAL_SCH5027[] = {5000, 2250, 3300, 1125, 1125, 3300,
3300};
static const int IN_NOMINAL_SCH5127[] = {2500, 2250, 3300, 1125, 1125, 3300,
- 3300};
+ 3300, 1500};
#define IN_NOMINAL(type) ((type) == sch311x ? IN_NOMINAL_SCH311x : \
(type) == sch5027 ? IN_NOMINAL_SCH5027 : \
(type) == sch5127 ? IN_NOMINAL_SCH5127 : \
{
struct dme1737_data *data = dev_get_drvdata(dev);
int ix;
- u8 lsb[5];
+ u8 lsb[6];
mutex_lock(&data->update_lock);
/* Voltage inputs are stored as 16 bit values even
* though they have only 12 bits resolution. This is
* to make it consistent with the temp inputs. */
+ if (ix == 7 && !(data->has_features & HAS_IN7)) {
+ continue;
+ }
data->in[ix] = dme1737_read(data,
DME1737_REG_IN(ix)) << 8;
data->in_min[ix] = dme1737_read(data,
* which the registers are read (MSB first, then LSB) is
* important! */
for (ix = 0; ix < ARRAY_SIZE(lsb); ix++) {
+ if (ix == 5 && !(data->has_features & HAS_IN7)) {
+ continue;
+ }
lsb[ix] = dme1737_read(data,
DME1737_REG_IN_TEMP_LSB(ix));
}
for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) {
+ if (ix == 7 && !(data->has_features & HAS_IN7)) {
+ continue;
+ }
data->in[ix] |= (lsb[DME1737_REG_IN_LSB[ix]] <<
DME1737_REG_IN_LSB_SHL[ix]) & 0xf0;
}
/* ---------------------------------------------------------------------
* Voltage sysfs attributes
- * ix = [0-5]
+ * ix = [0-7]
* --------------------------------------------------------------------- */
#define SYS_IN_INPUT 0
* Sysfs device attribute defines and structs
* --------------------------------------------------------------------- */
-/* Voltages 0-6 */
+/* Voltages 0-7 */
#define SENSOR_DEVICE_ATTR_IN(ix) \
static SENSOR_DEVICE_ATTR_2(in##ix##_input, S_IRUGO, \
SENSOR_DEVICE_ATTR_IN(4);
SENSOR_DEVICE_ATTR_IN(5);
SENSOR_DEVICE_ATTR_IN(6);
+SENSOR_DEVICE_ATTR_IN(7);
/* Temperatures 1-3 */
* created unconditionally. The attributes that need modification of their
* permissions are created read-only and write permissions are added or removed
* on the fly when required */
-static struct attribute *dme1737_attr[] ={
+static struct attribute *dme1737_attr[] = {
/* Voltages */
&sensor_dev_attr_in0_input.dev_attr.attr,
&sensor_dev_attr_in0_min.dev_attr.attr,
};
-/* The following struct holds temp zone hysteresis related attributes, which
+/* The following struct holds temp zone hysteresis related attributes, which
* are not available in all chips. The following chips support them:
* DME1737, SCH311x */
static struct attribute *dme1737_zone_hyst_attr[] = {
.attrs = dme1737_zone_hyst_attr,
};
+/* The following struct holds voltage in7 related attributes, which
+ * are not available in all chips. The following chips support them:
+ * SCH5127 */
+static struct attribute *dme1737_in7_attr[] = {
+ &sensor_dev_attr_in7_input.dev_attr.attr,
+ &sensor_dev_attr_in7_min.dev_attr.attr,
+ &sensor_dev_attr_in7_max.dev_attr.attr,
+ &sensor_dev_attr_in7_alarm.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group dme1737_in7_group = {
+ .attrs = dme1737_in7_attr,
+};
+
/* The following structs hold the PWM attributes, some of which are optional.
* Their creation depends on the chip configuration which is determined during
* module load. */
if (data->has_features & HAS_ZONE_HYST) {
sysfs_remove_group(&dev->kobj, &dme1737_zone_hyst_group);
}
+ if (data->has_features & HAS_IN7) {
+ sysfs_remove_group(&dev->kobj, &dme1737_in7_group);
+ }
sysfs_remove_group(&dev->kobj, &dme1737_group);
if (!data->client) {
int err, ix;
/* Create a name attribute for ISA devices */
- if (!data->client &&
- (err = sysfs_create_file(&dev->kobj, &dev_attr_name.attr))) {
- goto exit;
+ if (!data->client) {
+ err = sysfs_create_file(&dev->kobj, &dev_attr_name.attr);
+ if (err) {
+ goto exit;
+ }
}
/* Create standard sysfs attributes */
- if ((err = sysfs_create_group(&dev->kobj, &dme1737_group))) {
+ err = sysfs_create_group(&dev->kobj, &dme1737_group);
+ if (err) {
goto exit_remove;
}
/* Create chip-dependent sysfs attributes */
- if ((data->has_features & HAS_TEMP_OFFSET) &&
- (err = sysfs_create_group(&dev->kobj,
- &dme1737_temp_offset_group))) {
- goto exit_remove;
+ if (data->has_features & HAS_TEMP_OFFSET) {
+ err = sysfs_create_group(&dev->kobj,
+ &dme1737_temp_offset_group);
+ if (err) {
+ goto exit_remove;
+ }
}
- if ((data->has_features & HAS_VID) &&
- (err = sysfs_create_group(&dev->kobj,
- &dme1737_vid_group))) {
- goto exit_remove;
+ if (data->has_features & HAS_VID) {
+ err = sysfs_create_group(&dev->kobj, &dme1737_vid_group);
+ if (err) {
+ goto exit_remove;
+ }
}
- if ((data->has_features & HAS_ZONE3) &&
- (err = sysfs_create_group(&dev->kobj,
- &dme1737_zone3_group))) {
- goto exit_remove;
+ if (data->has_features & HAS_ZONE3) {
+ err = sysfs_create_group(&dev->kobj, &dme1737_zone3_group);
+ if (err) {
+ goto exit_remove;
+ }
}
- if ((data->has_features & HAS_ZONE_HYST) &&
- (err = sysfs_create_group(&dev->kobj,
- &dme1737_zone_hyst_group))) {
- goto exit_remove;
+ if (data->has_features & HAS_ZONE_HYST) {
+ err = sysfs_create_group(&dev->kobj, &dme1737_zone_hyst_group);
+ if (err) {
+ goto exit_remove;
+ }
+ }
+ if (data->has_features & HAS_IN7) {
+ err = sysfs_create_group(&dev->kobj, &dme1737_in7_group);
+ if (err) {
+ goto exit_remove;
+ }
}
/* Create fan sysfs attributes */
for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) {
if (data->has_features & HAS_FAN(ix)) {
- if ((err = sysfs_create_group(&dev->kobj,
- &dme1737_fan_group[ix]))) {
+ err = sysfs_create_group(&dev->kobj,
+ &dme1737_fan_group[ix]);
+ if (err) {
goto exit_remove;
}
}
/* Create PWM sysfs attributes */
for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_group); ix++) {
if (data->has_features & HAS_PWM(ix)) {
- if ((err = sysfs_create_group(&dev->kobj,
- &dme1737_pwm_group[ix]))) {
+ err = sysfs_create_group(&dev->kobj,
+ &dme1737_pwm_group[ix]);
+ if (err) {
goto exit_remove;
}
- if ((data->has_features & HAS_PWM_MIN) && ix < 3 &&
- (err = sysfs_create_file(&dev->kobj,
- dme1737_auto_pwm_min_attr[ix]))) {
- goto exit_remove;
+ if ((data->has_features & HAS_PWM_MIN) && (ix < 3)) {
+ err = sysfs_create_file(&dev->kobj,
+ dme1737_auto_pwm_min_attr[ix]);
+ if (err) {
+ goto exit_remove;
+ }
}
}
}
data->has_features |= HAS_ZONE3;
break;
case sch5127:
- data->has_features |= HAS_FAN(2) | HAS_PWM(2);
+ data->has_features |= HAS_FAN(2) | HAS_PWM(2) | HAS_IN7;
break;
default:
break;
dme1737_sio_outb(sio_cip, 0x07, 0x0a);
/* Get the base address of the runtime registers */
- if (!(addr = (dme1737_sio_inb(sio_cip, 0x60) << 8) |
- dme1737_sio_inb(sio_cip, 0x61))) {
+ addr = (dme1737_sio_inb(sio_cip, 0x60) << 8) |
+ dme1737_sio_inb(sio_cip, 0x61);
+ if (!addr) {
err = -ENODEV;
goto exit;
}
mutex_init(&data->update_lock);
/* Initialize the DME1737 chip */
- if ((err = dme1737_init_device(dev))) {
+ err = dme1737_init_device(dev);
+ if (err) {
dev_err(dev, "Failed to initialize device.\n");
goto exit_kfree;
}
/* Create sysfs files */
- if ((err = dme1737_create_files(dev))) {
+ err = dme1737_create_files(dev);
+ if (err) {
dev_err(dev, "Failed to create sysfs files.\n");
goto exit_kfree;
}
dme1737_sio_outb(sio_cip, 0x07, 0x0a);
/* Get the base address of the runtime registers */
- if (!(base_addr = (dme1737_sio_inb(sio_cip, 0x60) << 8) |
- dme1737_sio_inb(sio_cip, 0x61))) {
+ base_addr = (dme1737_sio_inb(sio_cip, 0x60) << 8) |
+ dme1737_sio_inb(sio_cip, 0x61);
+ if (!base_addr) {
pr_err("Base address not set\n");
err = -ENODEV;
goto exit;
if (err)
goto exit;
- if (!(pdev = platform_device_alloc("dme1737", addr))) {
+ pdev = platform_device_alloc("dme1737", addr);
+ if (!pdev) {
pr_err("Failed to allocate device\n");
err = -ENOMEM;
goto exit;
}
- if ((err = platform_device_add_resources(pdev, &res, 1))) {
+ err = platform_device_add_resources(pdev, &res, 1);
+ if (err) {
pr_err("Failed to add device resource (err = %d)\n", err);
goto exit_device_put;
}
- if ((err = platform_device_add(pdev))) {
+ err = platform_device_add(pdev);
+ if (err) {
pr_err("Failed to add device (err = %d)\n", err);
goto exit_device_put;
}
dev_err(dev, "Failed to request region 0x%04x-0x%04x.\n",
(unsigned short)res->start,
(unsigned short)res->start + DME1737_EXTENT - 1);
- err = -EBUSY;
- goto exit;
- }
+ err = -EBUSY;
+ goto exit;
+ }
- if (!(data = kzalloc(sizeof(struct dme1737_data), GFP_KERNEL))) {
+ data = kzalloc(sizeof(struct dme1737_data), GFP_KERNEL);
+ if (!data) {
err = -ENOMEM;
goto exit_release_region;
}
data->type == sch5127 ? "SCH5127" : "SCH311x", data->addr);
/* Initialize the chip */
- if ((err = dme1737_init_device(dev))) {
+ err = dme1737_init_device(dev);
+ if (err) {
dev_err(dev, "Failed to initialize device.\n");
goto exit_kfree;
}
/* Create sysfs files */
- if ((err = dme1737_create_files(dev))) {
+ err = dme1737_create_files(dev);
+ if (err) {
dev_err(dev, "Failed to create sysfs files.\n");
goto exit_kfree;
}
int err;
unsigned short addr;
- if ((err = i2c_add_driver(&dme1737_i2c_driver))) {
+ err = i2c_add_driver(&dme1737_i2c_driver);
+ if (err) {
goto exit;
}
return 0;
}
- if ((err = platform_driver_register(&dme1737_isa_driver))) {
+ err = platform_driver_register(&dme1737_isa_driver);
+ if (err) {
goto exit_del_i2c_driver;
}
/* Sets global pdev as a side effect */
- if ((err = dme1737_isa_device_add(addr))) {
+ err = dme1737_isa_device_add(addr);
+ if (err) {
goto exit_del_isa_driver;
}
struct i2c_board_info *info)
{
int id;
- /* Check if thermal chip is SMSC and EMC1403 */
+ /* Check if thermal chip is SMSC and EMC1403 or EMC1423 */
id = i2c_smbus_read_byte_data(client, THERMAL_SMSC_ID_REG);
if (id != 0x5d)
return -ENODEV;
+ id = i2c_smbus_read_byte_data(client, THERMAL_PID_REG);
+ switch (id) {
+ case 0x21:
+ strlcpy(info->type, "emc1403", I2C_NAME_SIZE);
+ break;
+ case 0x23:
+ strlcpy(info->type, "emc1423", I2C_NAME_SIZE);
+ break;
/* Note: 0x25 is the 1404 which is very similar and this
driver could be extended */
- id = i2c_smbus_read_byte_data(client, THERMAL_PID_REG);
- if (id != 0x21)
+ default:
return -ENODEV;
+ }
id = i2c_smbus_read_byte_data(client, THERMAL_REVISION_REG);
if (id != 0x01)
return -ENODEV;
- strlcpy(info->type, "emc1403", I2C_NAME_SIZE);
return 0;
}
static const struct i2c_device_id emc1403_idtable[] = {
{ "emc1403", 0 },
+ { "emc1423", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, emc1403_idtable);
#include <linux/kref.h>
/* Addresses to scan */
-static DEFINE_MUTEX(watchdog_mutex);
static const unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END };
/* Insmod parameters */
static long watchdog_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
{
- static struct watchdog_info ident = {
+ struct watchdog_info ident = {
.options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT |
WDIOF_CARDRESET,
.identity = "FSC watchdog"
int i, ret = 0;
struct fschmd_data *data = filp->private_data;
- mutex_lock(&watchdog_mutex);
switch (cmd) {
case WDIOC_GETSUPPORT:
ident.firmware_version = data->revision;
default:
ret = -ENOTTY;
}
- mutex_unlock(&watchdog_mutex);
return ret;
}
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
case 0xffff: /* No device at all */
goto exit;
default:
- pr_debug(DRVNAME ": Unsupported chip (DEVID=0x%x)\n",
- chip_type);
+ pr_debug("Unsupported chip (DEVID=0x%x)\n", chip_type);
goto exit;
}
superio_select(PME);
if (!(superio_inb(IT87_ACT_REG) & 0x01)) {
- pr_info("it87: Device not activated, skipping\n");
+ pr_info("Device not activated, skipping\n");
goto exit;
}
*address = superio_inw(IT87_BASE_REG) & ~(IT87_EXTENT - 1);
if (*address == 0) {
- pr_info("it87: Base address not set, skipping\n");
+ pr_info("Base address not set, skipping\n");
goto exit;
}
err = 0;
sio_data->revision = superio_inb(DEVREV) & 0x0f;
- pr_info("it87: Found IT%04xF chip at 0x%x, revision %d\n",
+ pr_info("Found IT%04xF chip at 0x%x, revision %d\n",
chip_type, *address, sio_data->revision);
/* in8 (Vbat) is always internal */
} else {
/* We need at least 4 VID pins */
if (reg & 0x0f) {
- pr_info("it87: VID is disabled (pins used for GPIO)\n");
+ pr_info("VID is disabled (pins used for GPIO)\n");
sio_data->skip_vid = 1;
}
}
if (sio_data->type == it8720 && !(reg & (1 << 1))) {
reg |= (1 << 1);
superio_outb(IT87_SIO_PINX2_REG, reg);
- pr_notice("it87: Routing internal VCCH to in7\n");
+ pr_notice("Routing internal VCCH to in7\n");
}
if (reg & (1 << 0))
sio_data->internal |= (1 << 0);
sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
}
if (sio_data->beep_pin)
- pr_info("it87: Beeping is supported\n");
+ pr_info("Beeping is supported\n");
/* Disable specific features based on DMI strings */
board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR);
the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case
the same board is ever used in other systems. */
- pr_info("it87: Disabling pwm2 due to "
- "hardware constraints\n");
+ pr_info("Disabling pwm2 due to hardware constraints\n");
sio_data->skip_pwm = (1 << 1);
}
}
pdev = platform_device_alloc(DRVNAME, address);
if (!pdev) {
err = -ENOMEM;
- printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+ pr_err("Device allocation failed\n");
goto exit;
}
err = platform_device_add_resources(pdev, &res, 1);
if (err) {
- printk(KERN_ERR DRVNAME ": Device resource addition failed "
- "(%d)\n", err);
+ pr_err("Device resource addition failed (%d)\n", err);
goto exit_device_put;
}
err = platform_device_add_data(pdev, sio_data,
sizeof(struct it87_sio_data));
if (err) {
- printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
+ pr_err("Platform data allocation failed\n");
goto exit_device_put;
}
err = platform_device_add(pdev);
if (err) {
- printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
- err);
+ pr_err("Device addition failed (%d)\n", err);
goto exit_device_put;
}
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
* individually for the probing phase. */
for (port = address; port < address + LM78_EXTENT; port++) {
if (!request_region(port, 1, "lm78")) {
- pr_debug("lm78: Failed to request port 0x%x\n", port);
+ pr_debug("Failed to request port 0x%x\n", port);
goto release;
}
}
found = 1;
if (found)
- pr_info("lm78: Found an %s chip at %#x\n",
+ pr_info("Found an %s chip at %#x\n",
val & 0x80 ? "LM79" : "LM78", (int)address);
release:
pdev = platform_device_alloc("lm78", address);
if (!pdev) {
err = -ENOMEM;
- printk(KERN_ERR "lm78: Device allocation failed\n");
+ pr_err("Device allocation failed\n");
goto exit;
}
err = platform_device_add_resources(pdev, &res, 1);
if (err) {
- printk(KERN_ERR "lm78: Device resource addition failed "
- "(%d)\n", err);
+ pr_err("Device resource addition failed (%d)\n", err);
goto exit_device_put;
}
err = platform_device_add(pdev);
if (err) {
- printk(KERN_ERR "lm78: Device addition failed (%d)\n",
- err);
+ pr_err("Device addition failed (%d)\n", err);
goto exit_device_put;
}
* the standard Super-I/O addresses is used (0x2E/0x2F or 0x4E/0x4F).
*/
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
val = superio_inb(sioaddr, ACT);
if (!(val & 0x01)) {
- printk(KERN_INFO "pc87360: Device 0x%02x not "
- "activated\n", logdev[i]);
+ pr_info("Device 0x%02x not activated\n", logdev[i]);
continue;
}
val = (superio_inb(sioaddr, BASE) << 8)
| superio_inb(sioaddr, BASE + 1);
if (!val) {
- printk(KERN_INFO "pc87360: Base address not set for "
- "device 0x%02x\n", logdev[i]);
+ pr_info("Base address not set for device 0x%02x\n",
+ logdev[i]);
continue;
}
confreg[0] = superio_inb(sioaddr, 0xF0);
confreg[1] = superio_inb(sioaddr, 0xF1);
-#ifdef DEBUG
- printk(KERN_DEBUG "pc87360: Fan 1: mon=%d "
- "ctrl=%d inv=%d\n", (confreg[0]>>2)&1,
- (confreg[0]>>3)&1, (confreg[0]>>4)&1);
- printk(KERN_DEBUG "pc87360: Fan 2: mon=%d "
- "ctrl=%d inv=%d\n", (confreg[0]>>5)&1,
- (confreg[0]>>6)&1, (confreg[0]>>7)&1);
- printk(KERN_DEBUG "pc87360: Fan 3: mon=%d "
- "ctrl=%d inv=%d\n", confreg[1]&1,
- (confreg[1]>>1)&1, (confreg[1]>>2)&1);
-#endif
+ pr_debug("Fan %d: mon=%d ctrl=%d inv=%d\n", 1,
+ (confreg[0] >> 2) & 1, (confreg[0] >> 3) & 1,
+ (confreg[0] >> 4) & 1);
+ pr_debug("Fan %d: mon=%d ctrl=%d inv=%d\n", 2,
+ (confreg[0] >> 5) & 1, (confreg[0] >> 6) & 1,
+ (confreg[0] >> 7) & 1);
+ pr_debug("Fan %d: mon=%d ctrl=%d inv=%d\n", 3,
+ confreg[1] & 1, (confreg[1] >> 1) & 1,
+ (confreg[1] >> 2) & 1);
} else if (i==1) { /* Voltages */
/* Are we using thermistors? */
if (*devid == 0xE9) { /* PC87366 */
confreg[3] = superio_inb(sioaddr, 0x25);
if (confreg[2] & 0x40) {
- printk(KERN_INFO "pc87360: Using "
- "thermistors for temperature "
- "monitoring\n");
+ pr_info("Using thermistors for "
+ "temperature monitoring\n");
}
if (confreg[3] & 0xE0) {
- printk(KERN_INFO "pc87360: VID "
- "inputs routed (mode %u)\n",
- confreg[3] >> 5);
+ pr_info("VID inputs routed (mode %u)\n",
+ confreg[3] >> 5);
}
}
}
pdev = platform_device_alloc("pc87360", address);
if (!pdev) {
err = -ENOMEM;
- printk(KERN_ERR "pc87360: Device allocation failed\n");
+ pr_err("Device allocation failed\n");
goto exit;
}
err = platform_device_add_resources(pdev, res, res_count);
if (err) {
- printk(KERN_ERR "pc87360: Device resources addition failed "
- "(%d)\n", err);
+ pr_err("Device resources addition failed (%d)\n", err);
goto exit_device_put;
}
err = platform_device_add(pdev);
if (err) {
- printk(KERN_ERR "pc87360: Device addition failed (%d)\n",
- err);
+ pr_err("Device addition failed (%d)\n", err);
goto exit_device_put;
}
if (pc87360_find(0x2e, &devid, extra_isa)
&& pc87360_find(0x4e, &devid, extra_isa)) {
- printk(KERN_WARNING "pc87360: PC8736x not detected, "
- "module not inserted.\n");
+ pr_warn("PC8736x not detected, module not inserted\n");
return -ENODEV;
}
}
if (address == 0x0000) {
- printk(KERN_WARNING "pc87360: No active logical device, "
- "module not inserted.\n");
+ pr_warn("No active logical device, module not inserted\n");
return -ENODEV;
}
* mode, and voltages aren't supported at all.
*/
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
data = kzalloc(sizeof(struct pc87427_data), GFP_KERNEL);
if (!data) {
err = -ENOMEM;
- printk(KERN_ERR DRVNAME ": Out of memory\n");
+ pr_err("Out of memory\n");
goto exit;
}
pdev = platform_device_alloc(DRVNAME, res[0].start);
if (!pdev) {
err = -ENOMEM;
- printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+ pr_err("Device allocation failed\n");
goto exit;
}
err = platform_device_add_resources(pdev, res, res_count);
if (err) {
- printk(KERN_ERR DRVNAME ": Device resource addition failed "
- "(%d)\n", err);
+ pr_err("Device resource addition failed (%d)\n", err);
goto exit_device_put;
}
err = platform_device_add_data(pdev, sio_data,
sizeof(struct pc87427_sio_data));
if (err) {
- printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
+ pr_err("Platform data allocation failed\n");
goto exit_device_put;
}
err = platform_device_add(pdev);
if (err) {
- printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
- err);
+ pr_err("Device addition failed (%d)\n", err);
goto exit_device_put;
}
val = superio_inb(sioaddr, SIOREG_ACT);
if (!(val & 0x01)) {
- printk(KERN_INFO DRVNAME ": Logical device 0x%02x "
- "not activated\n", logdev[i]);
+ pr_info("Logical device 0x%02x not activated\n",
+ logdev[i]);
continue;
}
val = superio_inb(sioaddr, SIOREG_MAP);
if (val & 0x01) {
- printk(KERN_WARNING DRVNAME ": Logical device 0x%02x "
- "is memory-mapped, can't use\n", logdev[i]);
+ pr_warn("Logical device 0x%02x is memory-mapped, "
+ "can't use\n", logdev[i]);
continue;
}
val = (superio_inb(sioaddr, SIOREG_IOBASE) << 8)
| superio_inb(sioaddr, SIOREG_IOBASE + 1);
if (!val) {
- printk(KERN_INFO DRVNAME ": I/O base address not set "
- "for logical device 0x%02x\n", logdev[i]);
+ pr_info("I/O base address not set for logical device "
+ "0x%02x\n", logdev[i]);
continue;
}
sio_data->address[i] = val;
return 0;
}
+static void via686a_update_fan_div(struct via686a_data *data)
+{
+ int reg = via686a_read_value(data, VIA686A_REG_FANDIV);
+ data->fan_div[0] = (reg >> 4) & 0x03;
+ data->fan_div[1] = reg >> 6;
+}
+
static void __devinit via686a_init_device(struct via686a_data *data)
{
u8 reg;
via686a_write_value(data, VIA686A_REG_TEMP_MODE,
(reg & ~VIA686A_TEMP_MODE_MASK)
| VIA686A_TEMP_MODE_CONTINUOUS);
+
+ /* Pre-read fan clock divisor values */
+ via686a_update_fan_div(data);
}
static struct via686a_data *via686a_update_device(struct device *dev)
(via686a_read_value(data, VIA686A_REG_TEMP_LOW23) &
0xc0) >> 6;
- i = via686a_read_value(data, VIA686A_REG_FANDIV);
- data->fan_div[0] = (i >> 4) & 0x03;
- data->fan_div[1] = i >> 6;
+ via686a_update_fan_div(data);
data->alarms =
via686a_read_value(data,
VIA686A_REG_ALARM1) |
*/
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
* individually for the probing phase. */
for (port = address; port < address + W83781D_EXTENT; port++) {
if (!request_region(port, 1, "w83781d")) {
- pr_debug("w83781d: Failed to request port 0x%x\n",
- port);
+ pr_debug("Failed to request port 0x%x\n", port);
goto release;
}
}
if (inb_p(address + 2) != val
|| inb_p(address + 3) != val
|| inb_p(address + 7) != val) {
- pr_debug("w83781d: Detection failed at step 1\n");
+ pr_debug("Detection failed at step %d\n", 1);
goto release;
}
#undef REALLY_SLOW_IO
MSB (busy flag) should be clear initially, set after the write. */
save = inb_p(address + W83781D_ADDR_REG_OFFSET);
if (save & 0x80) {
- pr_debug("w83781d: Detection failed at step 2\n");
+ pr_debug("Detection failed at step %d\n", 2);
goto release;
}
val = ~save & 0x7f;
outb_p(val, address + W83781D_ADDR_REG_OFFSET);
if (inb_p(address + W83781D_ADDR_REG_OFFSET) != (val | 0x80)) {
outb_p(save, address + W83781D_ADDR_REG_OFFSET);
- pr_debug("w83781d: Detection failed at step 3\n");
+ pr_debug("Detection failed at step %d\n", 3);
goto release;
}
outb_p(W83781D_REG_CONFIG, address + W83781D_ADDR_REG_OFFSET);
val = inb_p(address + W83781D_DATA_REG_OFFSET);
if (val & 0x80) {
- pr_debug("w83781d: Detection failed at step 4\n");
+ pr_debug("Detection failed at step %d\n", 4);
goto release;
}
outb_p(W83781D_REG_BANK, address + W83781D_ADDR_REG_OFFSET);
val = inb_p(address + W83781D_DATA_REG_OFFSET);
if ((!(save & 0x80) && (val != 0xa3))
|| ((save & 0x80) && (val != 0x5c))) {
- pr_debug("w83781d: Detection failed at step 5\n");
+ pr_debug("Detection failed at step %d\n", 5);
goto release;
}
outb_p(W83781D_REG_I2C_ADDR, address + W83781D_ADDR_REG_OFFSET);
val = inb_p(address + W83781D_DATA_REG_OFFSET);
if (val < 0x03 || val > 0x77) { /* Not a valid I2C address */
- pr_debug("w83781d: Detection failed at step 6\n");
+ pr_debug("Detection failed at step %d\n", 6);
goto release;
}
/* The busy flag should be clear again */
if (inb_p(address + W83781D_ADDR_REG_OFFSET) & 0x80) {
- pr_debug("w83781d: Detection failed at step 7\n");
+ pr_debug("Detection failed at step %d\n", 7);
goto release;
}
found = 1;
if (found)
- pr_info("w83781d: Found a %s chip at %#x\n",
+ pr_info("Found a %s chip at %#x\n",
val == 0x30 ? "W83782D" : "W83781D", (int)address);
release:
pdev = platform_device_alloc("w83781d", address);
if (!pdev) {
err = -ENOMEM;
- printk(KERN_ERR "w83781d: Device allocation failed\n");
+ pr_err("Device allocation failed\n");
goto exit;
}
err = platform_device_add_resources(pdev, &res, 1);
if (err) {
- printk(KERN_ERR "w83781d: Device resource addition failed "
- "(%d)\n", err);
+ pr_err("Device resource addition failed (%d)\n", err);
goto exit_device_put;
}
err = platform_device_add(pdev);
if (err) {
- printk(KERN_ERR "w83781d: Device addition failed (%d)\n",
- err);
+ pr_err("Device addition failed (%d)\n", err);
goto exit_device_put;
}
}
static ssize_t
-show_regs_chassis(struct device *dev, struct device_attribute *attr,
+show_chassis(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct w83792d_data *data = w83792d_update_device(dev);
}
static ssize_t
+show_regs_chassis(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ dev_warn(dev,
+ "Attribute %s is deprecated, use intrusion0_alarm instead\n",
+ "chassis");
+ return show_chassis(dev, attr, buf);
+}
+
+static ssize_t
show_chassis_clear(struct device *dev, struct device_attribute *attr, char *buf)
{
struct w83792d_data *data = w83792d_update_device(dev);
}
static ssize_t
-store_chassis_clear(struct device *dev, struct device_attribute *attr,
+store_chassis_clear_legacy(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
u32 val;
u8 temp1 = 0, temp2 = 0;
+ dev_warn(dev,
+ "Attribute %s is deprecated, use intrusion0_alarm instead\n",
+ "chassis_clear");
+
val = simple_strtoul(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->chassis_clear = SENSORS_LIMIT(val, 0 ,1);
return count;
}
+static ssize_t
+store_chassis_clear(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83792d_data *data = i2c_get_clientdata(client);
+ unsigned long val;
+ u8 reg;
+
+ if (strict_strtoul(buf, 10, &val) || val != 0)
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+ reg = w83792d_read_value(client, W83792D_REG_CHASSIS_CLR);
+ w83792d_write_value(client, W83792D_REG_CHASSIS_CLR, reg | 0x80);
+ data->valid = 0; /* Force cache refresh */
+ mutex_unlock(&data->update_lock);
+
+ return count;
+}
+
/* For Smart Fan I / Thermal Cruise */
static ssize_t
show_thermal_cruise(struct device *dev, struct device_attribute *attr,
static SENSOR_DEVICE_ATTR(fan6_alarm, S_IRUGO, show_alarm, NULL, 23);
static DEVICE_ATTR(chassis, S_IRUGO, show_regs_chassis, NULL);
static DEVICE_ATTR(chassis_clear, S_IRUGO | S_IWUSR,
- show_chassis_clear, store_chassis_clear);
+ show_chassis_clear, store_chassis_clear_legacy);
+static DEVICE_ATTR(intrusion0_alarm, S_IRUGO | S_IWUSR,
+ show_chassis, store_chassis_clear);
static SENSOR_DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 0);
static SENSOR_DEVICE_ATTR(pwm2, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 1);
static SENSOR_DEVICE_ATTR(pwm3, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 2);
&dev_attr_alarms.attr,
&dev_attr_chassis.attr,
&dev_attr_chassis_clear.attr,
+ &dev_attr_intrusion0_alarm.attr,
&sensor_dev_attr_tolerance1.dev_attr.attr,
&sensor_dev_attr_thermal_cruise1.dev_attr.attr,
&sensor_dev_attr_tolerance2.dev_attr.attr,
#define WATCHDOG_TIMEOUT 2 /* 2 minute default timeout */
/* Addresses to scan */
-static DEFINE_MUTEX(watchdog_mutex);
static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
I2C_CLIENT_END };
/* Write any value to clear chassis alarm */
static ssize_t
-store_chassis_clear(struct device *dev,
- struct device_attribute *attr, const char *buf,
- size_t count)
+store_chassis_clear_legacy(struct device *dev,
+ struct device_attribute *attr, const char *buf,
+ size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct w83793_data *data = i2c_get_clientdata(client);
u8 val;
+ dev_warn(dev, "Attribute chassis is deprecated, "
+ "use intrusion0_alarm instead\n");
+
mutex_lock(&data->update_lock);
val = w83793_read_value(client, W83793_REG_CLR_CHASSIS);
val |= 0x80;
return count;
}
+/* Write 0 to clear chassis alarm */
+static ssize_t
+store_chassis_clear(struct device *dev,
+ struct device_attribute *attr, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct w83793_data *data = i2c_get_clientdata(client);
+ unsigned long val;
+ u8 reg;
+
+ if (strict_strtoul(buf, 10, &val) || val != 0)
+ return -EINVAL;
+
+ mutex_lock(&data->update_lock);
+ reg = w83793_read_value(client, W83793_REG_CLR_CHASSIS);
+ w83793_write_value(client, W83793_REG_CLR_CHASSIS, reg | 0x80);
+ data->valid = 0; /* Force cache refresh */
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
#define FAN_INPUT 0
#define FAN_MIN 1
static ssize_t
static struct sensor_device_attribute_2 sda_single_files[] = {
SENSOR_ATTR_2(chassis, S_IWUSR | S_IRUGO, show_alarm_beep,
+ store_chassis_clear_legacy, ALARM_STATUS, 30),
+ SENSOR_ATTR_2(intrusion0_alarm, S_IWUSR | S_IRUGO, show_alarm_beep,
store_chassis_clear, ALARM_STATUS, 30),
SENSOR_ATTR_2(beep_enable, S_IWUSR | S_IRUGO, show_beep_enable,
store_beep_enable, NOT_USED, NOT_USED),
static long watchdog_ioctl(struct file *filp, unsigned int cmd,
unsigned long arg)
{
- static struct watchdog_info ident = {
+ struct watchdog_info ident = {
.options = WDIOF_KEEPALIVEPING |
WDIOF_SETTIMEOUT |
WDIOF_CARDRESET,
int val, ret = 0;
struct w83793_data *data = filp->private_data;
- mutex_lock(&watchdog_mutex);
switch (cmd) {
case WDIOC_GETSUPPORT:
if (!nowayout)
default:
ret = -ENOTTY;
}
- mutex_unlock(&watchdog_mutex);
return ret;
}
{
struct w83795_data *data = i2c_get_clientdata(client);
int i, limit;
+ u8 lsb;
/* Read the voltage limits */
for (i = 0; i < ARRAY_SIZE(data->in); i++) {
}
/* Read the fan limits */
+ lsb = 0; /* Silent false gcc warning */
for (i = 0; i < ARRAY_SIZE(data->fan); i++) {
- u8 lsb;
-
/* Each register contains LSB for 2 fans, but we want to
* read it only once to save time */
if ((i & 1) == 0 && (data->has_fan & (3 << i)))
projects / linux-flexiantxendom0-natty.git / commitdiff