drivers/serial/sunsu.c

   1 /* $Id: su.c,v 1.55 2002/01/08 16:00:16 davem Exp $
   2  * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI
   3  *
   4  * Copyright (C) 1997  Eddie C. Dost  (ecd@skynet.be)
   5  * Copyright (C) 1998-1999  Pete Zaitcev   (zaitcev@yahoo.com)
   6  *
   7  * This is mainly a variation of 8250.c, credits go to authors mentioned
   8  * therein.  In fact this driver should be merged into the generic 8250.c
   9  * infrastructure perhaps using a 8250_sparc.c module.
  10  *
  11  * Fixed to use tty_get_baud_rate().
  12  *   Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12
  13  *
  14  * Converted to new 2.5.x UART layer.
  15  *   David S. Miller (davem@redhat.com), 2002-Jul-29
  16  */
  17
  18 #include <linux/config.h>
  19 #include <linux/module.h>
  20 #include <linux/kernel.h>
  21 #include <linux/sched.h>
  22 #include <linux/spinlock.h>
  23 #include <linux/errno.h>
  24 #include <linux/tty.h>
  25 #include <linux/tty_flip.h>
  26 #include <linux/major.h>
  27 #include <linux/string.h>
  28 #include <linux/ptrace.h>
  29 #include <linux/ioport.h>
  30 #include <linux/circ_buf.h>
  31 #include <linux/serial.h>
  32 #include <linux/sysrq.h>
  33 #include <linux/console.h>
  34 #ifdef CONFIG_SERIO
  35 #include <linux/serio.h>
  36 #endif
  37 #include <linux/serial_reg.h>
  38 #include <linux/init.h>
  39 #include <linux/delay.h>
  40
  41 #include <asm/io.h>
  42 #include <asm/irq.h>
  43 #include <asm/oplib.h>
  44 #include <asm/ebus.h>
  45 #ifdef CONFIG_SPARC64
  46 #include <asm/isa.h>
  47 #endif
  48
  49 #if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  50 #define SUPPORT_SYSRQ
  51 #endif
  52
  53 #include <linux/serial_core.h>
  54
  55 #include "suncore.h"
  56
  57 /* We are on a NS PC87303 clocked with 24.0 MHz, which results
  58  * in a UART clock of 1.8462 MHz.
  59  */
  60 #define SU_BASE_BAUD    (1846200 / 16)
  61
  62 enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT };
  63 static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" };
  64
  65 /*
  66  * Here we define the default xmit fifo size used for each type of UART.
  67  */
  68 static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
  69         { "unknown",    1,      0 },
  70         { "8250",       1,      0 },
  71         { "16450",      1,      0 },
  72         { "16550",      1,      0 },
  73         { "16550A",     16,     UART_CLEAR_FIFO | UART_USE_FIFO },
  74         { "Cirrus",     1,      0 },
  75         { "ST16650",    1,      UART_CLEAR_FIFO | UART_STARTECH },
  76         { "ST16650V2",  32,     UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
  77         { "TI16750",    64,     UART_CLEAR_FIFO | UART_USE_FIFO },
  78         { "Startech",   1,      0 },
  79         { "16C950/954", 128,    UART_CLEAR_FIFO | UART_USE_FIFO },
  80         { "ST16654",    64,     UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
  81         { "XR16850",    128,    UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
  82         { "RSA",        2048,   UART_CLEAR_FIFO | UART_USE_FIFO }
  83 };
  84
  85 struct uart_sunsu_port {
  86         struct uart_port        port;
  87         unsigned char           acr;
  88         unsigned char           ier;
  89         unsigned short          rev;
  90         unsigned char           lcr;
  91         unsigned int            lsr_break_flag;
  92         unsigned int            cflag;
  93
  94         /* Probing information.  */
  95         enum su_type            su_type;
  96         unsigned int            type_probed;    /* XXX Stupid */
  97         int                     port_node;
  98
  99 #ifdef CONFIG_SERIO
 100         struct serio            *serio;
 101         int                     serio_open;
 102 #endif
 103 };
 104
 105 #define _INLINE_
 106
 107 static _INLINE_ unsigned int serial_in(struct uart_sunsu_port *up, int offset)
 108 {
 109         offset <<= up->port.regshift;
 110
 111         switch (up->port.iotype) {
 112         case SERIAL_IO_HUB6:
 113                 outb(up->port.hub6 - 1 + offset, up->port.iobase);
 114                 return inb(up->port.iobase + 1);
 115
 116         case SERIAL_IO_MEM:
 117                 return readb(up->port.membase + offset);
 118
 119         default:
 120                 return inb(up->port.iobase + offset);
 121         }
 122 }
 123
 124 static _INLINE_ void
 125 serial_out(struct uart_sunsu_port *up, int offset, int value)
 126 {
 127 #ifndef CONFIG_SPARC64
 128         /*
 129          * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are
 130          * connected with a gate then go to SlavIO. When IRQ4 goes tristated
 131          * gate outputs a logical one. Since we use level triggered interrupts
 132          * we have lockup and watchdog reset. We cannot mask IRQ because
 133          * keyboard shares IRQ with us (Word has it as Bob Smelik's design).
 134          * This problem is similar to what Alpha people suffer, see serial.c.
 135          */
 136         if (offset == UART_MCR)
 137                 value |= UART_MCR_OUT2;
 138 #endif
 139         offset <<= up->port.regshift;
 140
 141         switch (up->port.iotype) {
 142         case SERIAL_IO_HUB6:
 143                 outb(up->port.hub6 - 1 + offset, up->port.iobase);
 144                 outb(value, up->port.iobase + 1);
 145                 break;
 146
 147         case SERIAL_IO_MEM:
 148                 writeb(value, up->port.membase + offset);
 149                 break;
 150
 151         default:
 152                 outb(value, up->port.iobase + offset);
 153         }
 154 }
 155
 156 /*
 157  * We used to support using pause I/O for certain machines.  We
 158  * haven't supported this for a while, but just in case it's badly
 159  * needed for certain old 386 machines, I've left these #define's
 160  * in....
 161  */
 162 #define serial_inp(up, offset)          serial_in(up, offset)
 163 #define serial_outp(up, offset, value)  serial_out(up, offset, value)
 164
 165
 166 /*
 167  * For the 16C950
 168  */
 169 static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value)
 170 {
 171         serial_out(up, UART_SCR, offset);
 172         serial_out(up, UART_ICR, value);
 173 }
 174
 175 #if 0 /* Unused currently */
 176 static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset)
 177 {
 178         unsigned int value;
 179
 180         serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
 181         serial_out(up, UART_SCR, offset);
 182         value = serial_in(up, UART_ICR);
 183         serial_icr_write(up, UART_ACR, up->acr);
 184
 185         return value;
 186 }
 187 #endif
 188
 189 #ifdef CONFIG_SERIAL_8250_RSA
 190 /*
 191  * Attempts to turn on the RSA FIFO.  Returns zero on failure.
 192  * We set the port uart clock rate if we succeed.
 193  */
 194 static int __enable_rsa(struct uart_sunsu_port *up)
 195 {
 196         unsigned char mode;
 197         int result;
 198
 199         mode = serial_inp(up, UART_RSA_MSR);
 200         result = mode & UART_RSA_MSR_FIFO;
 201
 202         if (!result) {
 203                 serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
 204                 mode = serial_inp(up, UART_RSA_MSR);
 205                 result = mode & UART_RSA_MSR_FIFO;
 206         }
 207
 208         if (result)
 209                 up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
 210
 211         return result;
 212 }
 213
 214 static void enable_rsa(struct uart_sunsu_port *up)
 215 {
 216         if (up->port.type == PORT_RSA) {
 217                 if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
 218                         spin_lock_irq(&up->port.lock);
 219                         __enable_rsa(up);
 220                         spin_unlock_irq(&up->port.lock);
 221                 }
 222                 if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
 223                         serial_outp(up, UART_RSA_FRR, 0);
 224         }
 225 }
 226
 227 /*
 228  * Attempts to turn off the RSA FIFO.  Returns zero on failure.
 229  * It is unknown why interrupts were disabled in here.  However,
 230  * the caller is expected to preserve this behaviour by grabbing
 231  * the spinlock before calling this function.
 232  */
 233 static void disable_rsa(struct uart_sunsu_port *up)
 234 {
 235         unsigned char mode;
 236         int result;
 237
 238         if (up->port.type == PORT_RSA &&
 239             up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
 240                 spin_lock_irq(&up->port.lock);
 241
 242                 mode = serial_inp(up, UART_RSA_MSR);
 243                 result = !(mode & UART_RSA_MSR_FIFO);
 244
 245                 if (!result) {
 246                         serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
 247                         mode = serial_inp(up, UART_RSA_MSR);
 248                         result = !(mode & UART_RSA_MSR_FIFO);
 249                 }
 250
 251                 if (result)
 252                         up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
 253                 spin_unlock_irq(&up->port.lock);
 254         }
 255 }
 256 #endif /* CONFIG_SERIAL_8250_RSA */
 257
 258 static void sunsu_stop_tx(struct uart_port *port, unsigned int tty_stop)
 259 {
 260         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 261
 262         if (up->ier & UART_IER_THRI) {
 263                 up->ier &= ~UART_IER_THRI;
 264                 serial_out(up, UART_IER, up->ier);
 265         }
 266         if (up->port.type == PORT_16C950 && tty_stop) {
 267                 up->acr |= UART_ACR_TXDIS;
 268                 serial_icr_write(up, UART_ACR, up->acr);
 269         }
 270 }
 271
 272 static void sunsu_start_tx(struct uart_port *port, unsigned int tty_start)
 273 {
 274         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 275
 276         if (!(up->ier & UART_IER_THRI)) {
 277                 up->ier |= UART_IER_THRI;
 278                 serial_out(up, UART_IER, up->ier);
 279         }
 280         /*
 281          * We only do this from uart_start
 282          */
 283         if (tty_start && up->port.type == PORT_16C950) {
 284                 up->acr &= ~UART_ACR_TXDIS;
 285                 serial_icr_write(up, UART_ACR, up->acr);
 286         }
 287 }
 288
 289 static void sunsu_stop_rx(struct uart_port *port)
 290 {
 291         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 292         unsigned long flags;
 293
 294         spin_lock_irqsave(&up->port.lock, flags);
 295         up->ier &= ~UART_IER_RLSI;
 296         up->port.read_status_mask &= ~UART_LSR_DR;
 297         serial_out(up, UART_IER, up->ier);
 298         spin_unlock_irqrestore(&up->port.lock, flags);
 299 }
 300
 301 static void sunsu_enable_ms(struct uart_port *port)
 302 {
 303         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 304         unsigned long flags;
 305
 306         spin_lock_irqsave(&up->port.lock, flags);
 307         up->ier |= UART_IER_MSI;
 308         serial_out(up, UART_IER, up->ier);
 309         spin_unlock_irqrestore(&up->port.lock, flags);
 310 }
 311
 312 static _INLINE_ struct tty_struct *
 313 receive_chars(struct uart_sunsu_port *up, unsigned char *status, struct pt_regs *regs)
 314 {
 315         struct tty_struct *tty = up->port.info->tty;
 316         unsigned char ch;
 317         int max_count = 256;
 318         int saw_console_brk = 0;
 319
 320         do {
 321                 if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
 322                         tty->flip.work.func((void *)tty);
 323                         if (tty->flip.count >= TTY_FLIPBUF_SIZE)
 324                                 return tty; // if TTY_DONT_FLIP is set
 325                 }
 326                 ch = serial_inp(up, UART_RX);
 327                 *tty->flip.char_buf_ptr = ch;
 328                 *tty->flip.flag_buf_ptr = TTY_NORMAL;
 329                 up->port.icount.rx++;
 330
 331                 if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
 332                                        UART_LSR_FE | UART_LSR_OE))) {
 333                         /*
 334                          * For statistics only
 335                          */
 336                         if (*status & UART_LSR_BI) {
 337                                 *status &= ~(UART_LSR_FE | UART_LSR_PE);
 338                                 up->port.icount.brk++;
 339                                 if (up->port.cons != NULL &&
 340                                     up->port.line == up->port.cons->index)
 341                                         saw_console_brk = 1;
 342                                 /*
 343                                  * We do the SysRQ and SAK checking
 344                                  * here because otherwise the break
 345                                  * may get masked by ignore_status_mask
 346                                  * or read_status_mask.
 347                                  */
 348                                 if (uart_handle_break(&up->port))
 349                                         goto ignore_char;
 350                         } else if (*status & UART_LSR_PE)
 351                                 up->port.icount.parity++;
 352                         else if (*status & UART_LSR_FE)
 353                                 up->port.icount.frame++;
 354                         if (*status & UART_LSR_OE)
 355                                 up->port.icount.overrun++;
 356
 357                         /*
 358                          * Mask off conditions which should be ingored.
 359                          */
 360                         *status &= up->port.read_status_mask;
 361
 362                         if (up->port.cons != NULL &&
 363                             up->port.line == up->port.cons->index) {
 364                                 /* Recover the break flag from console xmit */
 365                                 *status |= up->lsr_break_flag;
 366                                 up->lsr_break_flag = 0;
 367                         }
 368
 369                         if (*status & UART_LSR_BI) {
 370                                 *tty->flip.flag_buf_ptr = TTY_BREAK;
 371                         } else if (*status & UART_LSR_PE)
 372                                 *tty->flip.flag_buf_ptr = TTY_PARITY;
 373                         else if (*status & UART_LSR_FE)
 374                                 *tty->flip.flag_buf_ptr = TTY_FRAME;
 375                 }
 376                 if (uart_handle_sysrq_char(&up->port, ch, regs))
 377                         goto ignore_char;
 378                 if ((*status & up->port.ignore_status_mask) == 0) {
 379                         tty->flip.flag_buf_ptr++;
 380                         tty->flip.char_buf_ptr++;
 381                         tty->flip.count++;
 382                 }
 383                 if ((*status & UART_LSR_OE) &&
 384                     tty->flip.count < TTY_FLIPBUF_SIZE) {
 385                         /*
 386                          * Overrun is special, since it's reported
 387                          * immediately, and doesn't affect the current
 388                          * character.
 389                          */
 390                         *tty->flip.flag_buf_ptr = TTY_OVERRUN;
 391                         tty->flip.flag_buf_ptr++;
 392                         tty->flip.char_buf_ptr++;
 393                         tty->flip.count++;
 394                 }
 395         ignore_char:
 396                 *status = serial_inp(up, UART_LSR);
 397         } while ((*status & UART_LSR_DR) && (max_count-- > 0));
 398
 399         if (saw_console_brk)
 400                 sun_do_break();
 401
 402         return tty;
 403 }
 404
 405 static _INLINE_ void transmit_chars(struct uart_sunsu_port *up)
 406 {
 407         struct circ_buf *xmit = &up->port.info->xmit;
 408         int count;
 409
 410         if (up->port.x_char) {
 411                 serial_outp(up, UART_TX, up->port.x_char);
 412                 up->port.icount.tx++;
 413                 up->port.x_char = 0;
 414                 return;
 415         }
 416         if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
 417                 sunsu_stop_tx(&up->port, 0);
 418                 return;
 419         }
 420
 421         count = up->port.fifosize;
 422         do {
 423                 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
 424                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 425                 up->port.icount.tx++;
 426                 if (uart_circ_empty(xmit))
 427                         break;
 428         } while (--count > 0);
 429
 430         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 431                 uart_write_wakeup(&up->port);
 432
 433         if (uart_circ_empty(xmit))
 434                 sunsu_stop_tx(&up->port, 0);
 435 }
 436
 437 static _INLINE_ void check_modem_status(struct uart_sunsu_port *up)
 438 {
 439         int status;
 440
 441         status = serial_in(up, UART_MSR);
 442
 443         if ((status & UART_MSR_ANY_DELTA) == 0)
 444                 return;
 445
 446         if (status & UART_MSR_TERI)
 447                 up->port.icount.rng++;
 448         if (status & UART_MSR_DDSR)
 449                 up->port.icount.dsr++;
 450         if (status & UART_MSR_DDCD)
 451                 uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
 452         if (status & UART_MSR_DCTS)
 453                 uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
 454
 455         wake_up_interruptible(&up->port.info->delta_msr_wait);
 456 }
 457
 458 static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 459 {
 460         struct uart_sunsu_port *up = dev_id;
 461         unsigned long flags;
 462         unsigned char status;
 463
 464         spin_lock_irqsave(&up->port.lock, flags);
 465
 466         do {
 467                 struct tty_struct *tty;
 468
 469                 status = serial_inp(up, UART_LSR);
 470                 tty = NULL;
 471                 if (status & UART_LSR_DR)
 472                         tty = receive_chars(up, &status, regs);
 473                 check_modem_status(up);
 474                 if (status & UART_LSR_THRE)
 475                         transmit_chars(up);
 476
 477                 spin_unlock_irqrestore(&up->port.lock, flags);
 478
 479                 if (tty)
 480                         tty_flip_buffer_push(tty);
 481
 482                 spin_lock_irqsave(&up->port.lock, flags);
 483
 484         } while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT));
 485
 486         spin_unlock_irqrestore(&up->port.lock, flags);
 487
 488         return IRQ_HANDLED;
 489 }
 490
 491 /* Separate interrupt handling path for keyboard/mouse ports.  */
 492
 493 static void
 494 sunsu_change_speed(struct uart_port *port, unsigned int cflag,
 495                    unsigned int iflag, unsigned int quot);
 496
 497 static void sunsu_change_mouse_baud(struct uart_sunsu_port *up)
 498 {
 499         unsigned int cur_cflag = up->cflag;
 500         int quot, new_baud;
 501
 502         up->cflag &= ~CBAUD;
 503         up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
 504
 505         quot = up->port.uartclk / (16 * new_baud);
 506
 507         spin_unlock(&up->port.lock);
 508
 509         sunsu_change_speed(&up->port, up->cflag, 0, quot);
 510
 511         spin_lock(&up->port.lock);
 512 }
 513
 514 static void receive_kbd_ms_chars(struct uart_sunsu_port *up, struct pt_regs *regs, int is_break)
 515 {
 516         do {
 517                 unsigned char ch = serial_inp(up, UART_RX);
 518
 519                 /* Stop-A is handled by drivers/char/keyboard.c now. */
 520                 if (up->su_type == SU_PORT_KBD) {
 521 #ifdef CONFIG_SERIO
 522                         serio_interrupt(up->serio, ch, 0, regs);
 523 #endif
 524                 } else if (up->su_type == SU_PORT_MS) {
 525                         int ret = suncore_mouse_baud_detection(ch, is_break);
 526
 527                         switch (ret) {
 528                         case 2:
 529                                 sunsu_change_mouse_baud(up);
 530                                 /* fallthru */
 531                         case 1:
 532                                 break;
 533
 534                         case 0:
 535 #ifdef CONFIG_SERIO
 536                                 serio_interrupt(up->serio, ch, 0, regs);
 537 #endif
 538                                 break;
 539                         };
 540                 }
 541         } while (serial_in(up, UART_LSR) & UART_LSR_DR);
 542 }
 543
 544 static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id, struct pt_regs *regs)
 545 {
 546         struct uart_sunsu_port *up = dev_id;
 547
 548         if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) {
 549                 unsigned char status = serial_inp(up, UART_LSR);
 550
 551                 if ((status & UART_LSR_DR) || (status & UART_LSR_BI))
 552                         receive_kbd_ms_chars(up, regs,
 553                                              (status & UART_LSR_BI) != 0);
 554         }
 555
 556         return IRQ_HANDLED;
 557 }
 558
 559 static unsigned int sunsu_tx_empty(struct uart_port *port)
 560 {
 561         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 562         unsigned long flags;
 563         unsigned int ret;
 564
 565         spin_lock_irqsave(&up->port.lock, flags);
 566         ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
 567         spin_unlock_irqrestore(&up->port.lock, flags);
 568
 569         return ret;
 570 }
 571
 572 static unsigned int sunsu_get_mctrl(struct uart_port *port)
 573 {
 574         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 575         unsigned long flags;
 576         unsigned char status;
 577         unsigned int ret;
 578
 579         spin_lock_irqsave(&up->port.lock, flags);
 580         status = serial_in(up, UART_MSR);
 581         spin_unlock_irqrestore(&up->port.lock, flags);
 582
 583         ret = 0;
 584         if (status & UART_MSR_DCD)
 585                 ret |= TIOCM_CAR;
 586         if (status & UART_MSR_RI)
 587                 ret |= TIOCM_RNG;
 588         if (status & UART_MSR_DSR)
 589                 ret |= TIOCM_DSR;
 590         if (status & UART_MSR_CTS)
 591                 ret |= TIOCM_CTS;
 592         return ret;
 593 }
 594
 595 static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
 596 {
 597         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 598         unsigned char mcr = 0;
 599
 600         if (mctrl & TIOCM_RTS)
 601                 mcr |= UART_MCR_RTS;
 602         if (mctrl & TIOCM_DTR)
 603                 mcr |= UART_MCR_DTR;
 604         if (mctrl & TIOCM_OUT1)
 605                 mcr |= UART_MCR_OUT1;
 606         if (mctrl & TIOCM_OUT2)
 607                 mcr |= UART_MCR_OUT2;
 608         if (mctrl & TIOCM_LOOP)
 609                 mcr |= UART_MCR_LOOP;
 610
 611         serial_out(up, UART_MCR, mcr);
 612 }
 613
 614 static void sunsu_break_ctl(struct uart_port *port, int break_state)
 615 {
 616         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 617         unsigned long flags;
 618
 619         spin_lock_irqsave(&up->port.lock, flags);
 620         if (break_state == -1)
 621                 up->lcr |= UART_LCR_SBC;
 622         else
 623                 up->lcr &= ~UART_LCR_SBC;
 624         serial_out(up, UART_LCR, up->lcr);
 625         spin_unlock_irqrestore(&up->port.lock, flags);
 626 }
 627
 628 static int sunsu_startup(struct uart_port *port)
 629 {
 630         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 631         unsigned long flags;
 632         int retval;
 633
 634         if (up->port.type == PORT_16C950) {
 635                 /* Wake up and initialize UART */
 636                 up->acr = 0;
 637                 serial_outp(up, UART_LCR, 0xBF);
 638                 serial_outp(up, UART_EFR, UART_EFR_ECB);
 639                 serial_outp(up, UART_IER, 0);
 640                 serial_outp(up, UART_LCR, 0);
 641                 serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
 642                 serial_outp(up, UART_LCR, 0xBF);
 643                 serial_outp(up, UART_EFR, UART_EFR_ECB);
 644                 serial_outp(up, UART_LCR, 0);
 645         }
 646
 647 #ifdef CONFIG_SERIAL_8250_RSA
 648         /*
 649          * If this is an RSA port, see if we can kick it up to the
 650          * higher speed clock.
 651          */
 652         enable_rsa(up);
 653 #endif
 654
 655         /*
 656          * Clear the FIFO buffers and disable them.
 657          * (they will be reeanbled in set_termios())
 658          */
 659         if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
 660                 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
 661                 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
 662                                 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
 663                 serial_outp(up, UART_FCR, 0);
 664         }
 665
 666         /*
 667          * Clear the interrupt registers.
 668          */
 669         (void) serial_inp(up, UART_LSR);
 670         (void) serial_inp(up, UART_RX);
 671         (void) serial_inp(up, UART_IIR);
 672         (void) serial_inp(up, UART_MSR);
 673
 674         /*
 675          * At this point, there's no way the LSR could still be 0xff;
 676          * if it is, then bail out, because there's likely no UART
 677          * here.
 678          */
 679         if (!(up->port.flags & ASYNC_BUGGY_UART) &&
 680             (serial_inp(up, UART_LSR) == 0xff)) {
 681                 printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
 682                 return -ENODEV;
 683         }
 684
 685         if (up->su_type != SU_PORT_PORT) {
 686                 retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt,
 687                                      SA_SHIRQ, su_typev[up->su_type], up);
 688         } else {
 689                 retval = request_irq(up->port.irq, sunsu_serial_interrupt,
 690                                      SA_SHIRQ, su_typev[up->su_type], up);
 691         }
 692         if (retval) {
 693                 printk("su: Cannot register IRQ %d\n", up->port.irq);
 694                 return retval;
 695         }
 696
 697         /*
 698          * Now, initialize the UART
 699          */
 700         serial_outp(up, UART_LCR, UART_LCR_WLEN8);
 701
 702         spin_lock_irqsave(&up->port.lock, flags);
 703
 704         up->port.mctrl |= TIOCM_OUT2;
 705
 706         sunsu_set_mctrl(&up->port, up->port.mctrl);
 707         spin_unlock_irqrestore(&up->port.lock, flags);
 708
 709         /*
 710          * Finally, enable interrupts.  Note: Modem status interrupts
 711          * are set via set_termios(), which will be occurring imminently
 712          * anyway, so we don't enable them here.
 713          */
 714         up->ier = UART_IER_RLSI | UART_IER_RDI;
 715         serial_outp(up, UART_IER, up->ier);
 716
 717         if (up->port.flags & ASYNC_FOURPORT) {
 718                 unsigned int icp;
 719                 /*
 720                  * Enable interrupts on the AST Fourport board
 721                  */
 722                 icp = (up->port.iobase & 0xfe0) | 0x01f;
 723                 outb_p(0x80, icp);
 724                 (void) inb_p(icp);
 725         }
 726
 727         /*
 728          * And clear the interrupt registers again for luck.
 729          */
 730         (void) serial_inp(up, UART_LSR);
 731         (void) serial_inp(up, UART_RX);
 732         (void) serial_inp(up, UART_IIR);
 733         (void) serial_inp(up, UART_MSR);
 734
 735         return 0;
 736 }
 737
 738 static void sunsu_shutdown(struct uart_port *port)
 739 {
 740         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 741         unsigned long flags;
 742
 743         /*
 744          * Disable interrupts from this port
 745          */
 746         up->ier = 0;
 747         serial_outp(up, UART_IER, 0);
 748
 749         spin_lock_irqsave(&up->port.lock, flags);
 750         if (up->port.flags & ASYNC_FOURPORT) {
 751                 /* reset interrupts on the AST Fourport board */
 752                 inb((up->port.iobase & 0xfe0) | 0x1f);
 753                 up->port.mctrl |= TIOCM_OUT1;
 754         } else
 755                 up->port.mctrl &= ~TIOCM_OUT2;
 756
 757         sunsu_set_mctrl(&up->port, up->port.mctrl);
 758         spin_unlock_irqrestore(&up->port.lock, flags);
 759
 760         /*
 761          * Disable break condition and FIFOs
 762          */
 763         serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
 764         serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
 765                                   UART_FCR_CLEAR_RCVR |
 766                                   UART_FCR_CLEAR_XMIT);
 767         serial_outp(up, UART_FCR, 0);
 768
 769 #ifdef CONFIG_SERIAL_8250_RSA
 770         /*
 771          * Reset the RSA board back to 115kbps compat mode.
 772          */
 773         disable_rsa(up);
 774 #endif
 775
 776         /*
 777          * Read data port to reset things.
 778          */
 779         (void) serial_in(up, UART_RX);
 780
 781         free_irq(up->port.irq, up);
 782 }
 783
 784 static void
 785 sunsu_change_speed(struct uart_port *port, unsigned int cflag,
 786                    unsigned int iflag, unsigned int quot)
 787 {
 788         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 789         unsigned char cval, fcr = 0;
 790         unsigned long flags;
 791
 792         switch (cflag & CSIZE) {
 793         case CS5:
 794                 cval = 0x00;
 795                 break;
 796         case CS6:
 797                 cval = 0x01;
 798                 break;
 799         case CS7:
 800                 cval = 0x02;
 801                 break;
 802         default:
 803         case CS8:
 804                 cval = 0x03;
 805                 break;
 806         }
 807
 808         if (cflag & CSTOPB)
 809                 cval |= 0x04;
 810         if (cflag & PARENB)
 811                 cval |= UART_LCR_PARITY;
 812         if (!(cflag & PARODD))
 813                 cval |= UART_LCR_EPAR;
 814 #ifdef CMSPAR
 815         if (cflag & CMSPAR)
 816                 cval |= UART_LCR_SPAR;
 817 #endif
 818
 819         /*
 820          * Work around a bug in the Oxford Semiconductor 952 rev B
 821          * chip which causes it to seriously miscalculate baud rates
 822          * when DLL is 0.
 823          */
 824         if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
 825             up->rev == 0x5201)
 826                 quot ++;
 827
 828         if (uart_config[up->port.type].flags & UART_USE_FIFO) {
 829                 if ((up->port.uartclk / quot) < (2400 * 16))
 830                         fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
 831 #ifdef CONFIG_SERIAL_8250_RSA
 832                 else if (up->port.type == PORT_RSA)
 833                         fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14;
 834 #endif
 835                 else
 836                         fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8;
 837         }
 838         if (up->port.type == PORT_16750)
 839                 fcr |= UART_FCR7_64BYTE;
 840
 841         /*
 842          * Ok, we're now changing the port state.  Do it with
 843          * interrupts disabled.
 844          */
 845         spin_lock_irqsave(&up->port.lock, flags);
 846
 847         /*
 848          * Update the per-port timeout.
 849          */
 850         uart_update_timeout(port, cflag, (port->uartclk / (16 * quot)));
 851
 852         up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
 853         if (iflag & INPCK)
 854                 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
 855         if (iflag & (BRKINT | PARMRK))
 856                 up->port.read_status_mask |= UART_LSR_BI;
 857
 858         /*
 859          * Characteres to ignore
 860          */
 861         up->port.ignore_status_mask = 0;
 862         if (iflag & IGNPAR)
 863                 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
 864         if (iflag & IGNBRK) {
 865                 up->port.ignore_status_mask |= UART_LSR_BI;
 866                 /*
 867                  * If we're ignoring parity and break indicators,
 868                  * ignore overruns too (for real raw support).
 869                  */
 870                 if (iflag & IGNPAR)
 871                         up->port.ignore_status_mask |= UART_LSR_OE;
 872         }
 873
 874         /*
 875          * ignore all characters if CREAD is not set
 876          */
 877         if ((cflag & CREAD) == 0)
 878                 up->port.ignore_status_mask |= UART_LSR_DR;
 879
 880         /*
 881          * CTS flow control flag and modem status interrupts
 882          */
 883         up->ier &= ~UART_IER_MSI;
 884         if (UART_ENABLE_MS(&up->port, cflag))
 885                 up->ier |= UART_IER_MSI;
 886
 887         serial_out(up, UART_IER, up->ier);
 888
 889         if (uart_config[up->port.type].flags & UART_STARTECH) {
 890                 serial_outp(up, UART_LCR, 0xBF);
 891                 serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0);
 892         }
 893         serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
 894         serial_outp(up, UART_DLL, quot & 0xff);         /* LS of divisor */
 895         serial_outp(up, UART_DLM, quot >> 8);           /* MS of divisor */
 896         if (up->port.type == PORT_16750)
 897                 serial_outp(up, UART_FCR, fcr);         /* set fcr */
 898         serial_outp(up, UART_LCR, cval);                /* reset DLAB */
 899         up->lcr = cval;                                 /* Save LCR */
 900         if (up->port.type != PORT_16750) {
 901                 if (fcr & UART_FCR_ENABLE_FIFO) {
 902                         /* emulated UARTs (Lucent Venus 167x) need two steps */
 903                         serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
 904                 }
 905                 serial_outp(up, UART_FCR, fcr);         /* set fcr */
 906         }
 907
 908         up->cflag = cflag;
 909
 910         spin_unlock_irqrestore(&up->port.lock, flags);
 911 }
 912
 913 static void
 914 sunsu_set_termios(struct uart_port *port, struct termios *termios,
 915                   struct termios *old)
 916 {
 917         unsigned int baud, quot;
 918
 919         /*
 920          * Ask the core to calculate the divisor for us.
 921          */
 922         baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
 923         quot = uart_get_divisor(port, baud);
 924
 925         sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot);
 926 }
 927
 928 static void sunsu_release_port(struct uart_port *port)
 929 {
 930 }
 931
 932 static int sunsu_request_port(struct uart_port *port)
 933 {
 934         return 0;
 935 }
 936
 937 static void sunsu_config_port(struct uart_port *port, int flags)
 938 {
 939         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 940
 941         if (flags & UART_CONFIG_TYPE) {
 942                 /*
 943                  * We are supposed to call autoconfig here, but this requires
 944                  * splitting all the OBP probing crap from the UART probing.
 945                  * We'll do it when we kill sunsu.c altogether.
 946                  */
 947                 port->type = up->type_probed;   /* XXX */
 948         }
 949 }
 950
 951 static int
 952 sunsu_verify_port(struct uart_port *port, struct serial_struct *ser)
 953 {
 954         return -EINVAL;
 955 }
 956
 957 static const char *
 958 sunsu_type(struct uart_port *port)
 959 {
 960         int type = port->type;
 961
 962         if (type >= ARRAY_SIZE(uart_config))
 963                 type = 0;
 964         return uart_config[type].name;
 965 }
 966
 967 static struct uart_ops sunsu_pops = {
 968         .tx_empty       = sunsu_tx_empty,
 969         .set_mctrl      = sunsu_set_mctrl,
 970         .get_mctrl      = sunsu_get_mctrl,
 971         .stop_tx        = sunsu_stop_tx,
 972         .start_tx       = sunsu_start_tx,
 973         .stop_rx        = sunsu_stop_rx,
 974         .enable_ms      = sunsu_enable_ms,
 975         .break_ctl      = sunsu_break_ctl,
 976         .startup        = sunsu_startup,
 977         .shutdown       = sunsu_shutdown,
 978         .set_termios    = sunsu_set_termios,
 979         .type           = sunsu_type,
 980         .release_port   = sunsu_release_port,
 981         .request_port   = sunsu_request_port,
 982         .config_port    = sunsu_config_port,
 983         .verify_port    = sunsu_verify_port,
 984 };
 985
 986 #define UART_NR 4
 987
 988 static struct uart_sunsu_port sunsu_ports[UART_NR];
 989
 990 #ifdef CONFIG_SERIO
 991
 992 static DEFINE_SPINLOCK(sunsu_serio_lock);
 993
 994 static int sunsu_serio_write(struct serio *serio, unsigned char ch)
 995 {
 996         struct uart_sunsu_port *up = serio->port_data;
 997         unsigned long flags;
 998         int lsr;
 999
1000         spin_lock_irqsave(&sunsu_serio_lock, flags);
1001
1002         do {
1003                 lsr = serial_in(up, UART_LSR);
1004         } while (!(lsr & UART_LSR_THRE));
1005
1006         /* Send the character out. */
1007         serial_out(up, UART_TX, ch);
1008
1009         spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1010
1011         return 0;
1012 }
1013
1014 static int sunsu_serio_open(struct serio *serio)
1015 {
1016         struct uart_sunsu_port *up = serio->port_data;
1017         unsigned long flags;
1018         int ret;
1019
1020         spin_lock_irqsave(&sunsu_serio_lock, flags);
1021         if (!up->serio_open) {
1022                 up->serio_open = 1;
1023                 ret = 0;
1024         } else
1025                 ret = -EBUSY;
1026         spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1027
1028         return ret;
1029 }
1030
1031 static void sunsu_serio_close(struct serio *serio)
1032 {
1033         struct uart_sunsu_port *up = serio->port_data;
1034         unsigned long flags;
1035
1036         spin_lock_irqsave(&sunsu_serio_lock, flags);
1037         up->serio_open = 0;
1038         spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1039 }
1040
1041 #endif /* CONFIG_SERIO */
1042
1043 static void sunsu_autoconfig(struct uart_sunsu_port *up)
1044 {
1045         unsigned char status1, status2, scratch, scratch2, scratch3;
1046         unsigned char save_lcr, save_mcr;
1047         struct linux_ebus_device *dev = NULL;
1048         struct linux_ebus *ebus;
1049 #ifdef CONFIG_SPARC64
1050         struct sparc_isa_bridge *isa_br;
1051         struct sparc_isa_device *isa_dev;
1052 #endif
1053 #ifndef CONFIG_SPARC64
1054         struct linux_prom_registers reg0;
1055 #endif
1056         unsigned long flags;
1057
1058         if (!up->port_node || !up->su_type)
1059                 return;
1060
1061         up->type_probed = PORT_UNKNOWN;
1062         up->port.iotype = SERIAL_IO_MEM;
1063
1064         /*
1065          * First we look for Ebus-bases su's
1066          */
1067         for_each_ebus(ebus) {
1068                 for_each_ebusdev(dev, ebus) {
1069                         if (dev->prom_node == up->port_node) {
1070                                 /*
1071                                  * The EBus is broken on sparc; it delivers
1072                                  * virtual addresses in resources. Oh well...
1073                                  * This is correct on sparc64, though.
1074                                  */
1075                                 up->port.membase = (char *) dev->resource[0].start;
1076                                 /*
1077                                  * This is correct on both architectures.
1078                                  */
1079                                 up->port.mapbase = dev->resource[0].start;
1080                                 up->port.irq = dev->irqs[0];
1081                                 goto ebus_done;
1082                         }
1083                 }
1084         }
1085
1086 #ifdef CONFIG_SPARC64
1087         for_each_isa(isa_br) {
1088                 for_each_isadev(isa_dev, isa_br) {
1089                         if (isa_dev->prom_node == up->port_node) {
1090                                 /* Same on sparc64. Cool architecure... */
1091                                 up->port.membase = (char *) isa_dev->resource.start;
1092                                 up->port.mapbase = isa_dev->resource.start;
1093                                 up->port.irq = isa_dev->irq;
1094                                 goto ebus_done;
1095                         }
1096                 }
1097         }
1098 #endif
1099
1100 #ifdef CONFIG_SPARC64
1101         /*
1102          * Not on Ebus, bailing.
1103          */
1104         return;
1105 #else
1106         /*
1107          * Not on Ebus, must be OBIO.
1108          */
1109         if (prom_getproperty(up->port_node, "reg",
1110                              (char *)&reg0, sizeof(reg0)) == -1) {
1111                 prom_printf("sunsu: no \"reg\" property\n");
1112                 return;
1113         }
1114         prom_apply_obio_ranges(&reg0, 1);
1115         if (reg0.which_io != 0) {       /* Just in case... */
1116                 prom_printf("sunsu: bus number nonzero: 0x%x:%x\n",
1117                     reg0.which_io, reg0.phys_addr);
1118                 return;
1119         }
1120         up->port.mapbase = reg0.phys_addr;
1121         if ((up->port.membase = ioremap(reg0.phys_addr, reg0.reg_size)) == 0) {
1122                 prom_printf("sunsu: Cannot map registers.\n");
1123                 return;
1124         }
1125
1126         /*
1127          * 0x20 is sun4m thing, Dave Redman heritage.
1128          * See arch/sparc/kernel/irq.c.
1129          */
1130 #define IRQ_4M(n)       ((n)|0x20)
1131
1132         /*
1133          * There is no intr property on MrCoffee, so hardwire it.
1134          */
1135         up->port.irq = IRQ_4M(13);
1136 #endif
1137
1138 ebus_done:
1139
1140         spin_lock_irqsave(&up->port.lock, flags);
1141
1142         if (!(up->port.flags & ASYNC_BUGGY_UART)) {
1143                 /*
1144                  * Do a simple existence test first; if we fail this, there's
1145                  * no point trying anything else.
1146                  *
1147                  * 0x80 is used as a nonsense port to prevent against false
1148                  * positives due to ISA bus float.  The assumption is that
1149                  * 0x80 is a non-existent port; which should be safe since
1150                  * include/asm/io.h also makes this assumption.
1151                  */
1152                 scratch = serial_inp(up, UART_IER);
1153                 serial_outp(up, UART_IER, 0);
1154 #ifdef __i386__
1155                 outb(0xff, 0x080);
1156 #endif
1157                 scratch2 = serial_inp(up, UART_IER);
1158                 serial_outp(up, UART_IER, 0x0f);
1159 #ifdef __i386__
1160                 outb(0, 0x080);
1161 #endif
1162                 scratch3 = serial_inp(up, UART_IER);
1163                 serial_outp(up, UART_IER, scratch);
1164                 if (scratch2 != 0 || scratch3 != 0x0F)
1165                         goto out;       /* We failed; there's nothing here */
1166         }
1167
1168         save_mcr = serial_in(up, UART_MCR);
1169         save_lcr = serial_in(up, UART_LCR);
1170
1171         /*
1172          * Check to see if a UART is really there.  Certain broken
1173          * internal modems based on the Rockwell chipset fail this
1174          * test, because they apparently don't implement the loopback
1175          * test mode.  So this test is skipped on the COM 1 through
1176          * COM 4 ports.  This *should* be safe, since no board
1177          * manufacturer would be stupid enough to design a board
1178          * that conflicts with COM 1-4 --- we hope!
1179          */
1180         if (!(up->port.flags & ASYNC_SKIP_TEST)) {
1181                 serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
1182                 status1 = serial_inp(up, UART_MSR) & 0xF0;
1183                 serial_outp(up, UART_MCR, save_mcr);
1184                 if (status1 != 0x90)
1185                         goto out;       /* We failed loopback test */
1186         }
1187         serial_outp(up, UART_LCR, 0xBF);        /* set up for StarTech test */
1188         serial_outp(up, UART_EFR, 0);           /* EFR is the same as FCR */
1189         serial_outp(up, UART_LCR, 0);
1190         serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1191         scratch = serial_in(up, UART_IIR) >> 6;
1192         switch (scratch) {
1193                 case 0:
1194                         up->port.type = PORT_16450;
1195                         break;
1196                 case 1:
1197                         up->port.type = PORT_UNKNOWN;
1198                         break;
1199                 case 2:
1200                         up->port.type = PORT_16550;
1201                         break;
1202                 case 3:
1203                         up->port.type = PORT_16550A;
1204                         break;
1205         }
1206         if (up->port.type == PORT_16550A) {
1207                 /* Check for Startech UART's */
1208                 serial_outp(up, UART_LCR, UART_LCR_DLAB);
1209                 if (serial_in(up, UART_EFR) == 0) {
1210                         up->port.type = PORT_16650;
1211                 } else {
1212                         serial_outp(up, UART_LCR, 0xBF);
1213                         if (serial_in(up, UART_EFR) == 0)
1214                                 up->port.type = PORT_16650V2;
1215                 }
1216         }
1217         if (up->port.type == PORT_16550A) {
1218                 /* Check for TI 16750 */
1219                 serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB);
1220                 serial_outp(up, UART_FCR,
1221                             UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1222                 scratch = serial_in(up, UART_IIR) >> 5;
1223                 if (scratch == 7) {
1224                         /*
1225                          * If this is a 16750, and not a cheap UART
1226                          * clone, then it should only go into 64 byte
1227                          * mode if the UART_FCR7_64BYTE bit was set
1228                          * while UART_LCR_DLAB was latched.
1229                          */
1230                         serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1231                         serial_outp(up, UART_LCR, 0);
1232                         serial_outp(up, UART_FCR,
1233                                     UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1234                         scratch = serial_in(up, UART_IIR) >> 5;
1235                         if (scratch == 6)
1236                                 up->port.type = PORT_16750;
1237                 }
1238                 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1239         }
1240         serial_outp(up, UART_LCR, save_lcr);
1241         if (up->port.type == PORT_16450) {
1242                 scratch = serial_in(up, UART_SCR);
1243                 serial_outp(up, UART_SCR, 0xa5);
1244                 status1 = serial_in(up, UART_SCR);
1245                 serial_outp(up, UART_SCR, 0x5a);
1246                 status2 = serial_in(up, UART_SCR);
1247                 serial_outp(up, UART_SCR, scratch);
1248
1249                 if ((status1 != 0xa5) || (status2 != 0x5a))
1250                         up->port.type = PORT_8250;
1251         }
1252
1253         up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
1254
1255         if (up->port.type == PORT_UNKNOWN)
1256                 goto out;
1257         up->type_probed = up->port.type;        /* XXX */
1258
1259         /*
1260          * Reset the UART.
1261          */
1262 #ifdef CONFIG_SERIAL_8250_RSA
1263         if (up->port.type == PORT_RSA)
1264                 serial_outp(up, UART_RSA_FRR, 0);
1265 #endif
1266         serial_outp(up, UART_MCR, save_mcr);
1267         serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
1268                                      UART_FCR_CLEAR_RCVR |
1269                                      UART_FCR_CLEAR_XMIT));
1270         serial_outp(up, UART_FCR, 0);
1271         (void)serial_in(up, UART_RX);
1272         serial_outp(up, UART_IER, 0);
1273
1274 out:
1275         spin_unlock_irqrestore(&up->port.lock, flags);
1276 }
1277
1278 static struct uart_driver sunsu_reg = {
1279         .owner                  = THIS_MODULE,
1280         .driver_name            = "serial",
1281         .devfs_name             = "tts/",
1282         .dev_name               = "ttyS",
1283         .major                  = TTY_MAJOR,
1284 };
1285
1286 static int __init sunsu_kbd_ms_init(struct uart_sunsu_port *up, int channel)
1287 {
1288 #ifdef CONFIG_SERIO
1289         struct serio *serio;
1290 #endif
1291
1292         up->port.line = channel;
1293         up->port.type = PORT_UNKNOWN;
1294         up->port.uartclk = (SU_BASE_BAUD * 16);
1295
1296         if (up->su_type == SU_PORT_KBD)
1297                 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1298         else
1299                 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1300
1301         sunsu_autoconfig(up);
1302         if (up->port.type == PORT_UNKNOWN)
1303                 return -1;
1304
1305         printk(KERN_INFO "su%d at 0x%p (irq = %s) is a %s\n",
1306                channel,
1307                up->port.membase, __irq_itoa(up->port.irq),
1308                sunsu_type(&up->port));
1309
1310 #ifdef CONFIG_SERIO
1311         up->serio = serio = kmalloc(sizeof(struct serio), GFP_KERNEL);
1312         if (serio) {
1313                 memset(serio, 0, sizeof(*serio));
1314
1315                 serio->port_data = up;
1316
1317                 serio->id.type = SERIO_RS232;
1318                 if (up->su_type == SU_PORT_KBD) {
1319                         serio->id.proto = SERIO_SUNKBD;
1320                         strlcpy(serio->name, "sukbd", sizeof(serio->name));
1321                 } else {
1322                         serio->id.proto = SERIO_SUN;
1323                         serio->id.extra = 1;
1324                         strlcpy(serio->name, "sums", sizeof(serio->name));
1325                 }
1326                 strlcpy(serio->phys, (channel == 0 ? "su/serio0" : "su/serio1"),
1327                         sizeof(serio->phys));
1328
1329                 serio->write = sunsu_serio_write;
1330                 serio->open = sunsu_serio_open;
1331                 serio->close = sunsu_serio_close;
1332
1333                 serio_register_port(serio);
1334         } else {
1335                 printk(KERN_WARNING "su%d: not enough memory for serio port\n",
1336                         channel);
1337         }
1338 #endif
1339
1340         sunsu_startup(&up->port);
1341         return 0;
1342 }
1343
1344 /*
1345  * ------------------------------------------------------------
1346  * Serial console driver
1347  * ------------------------------------------------------------
1348  */
1349
1350 #ifdef CONFIG_SERIAL_SUNSU_CONSOLE
1351
1352 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1353
1354 /*
1355  *      Wait for transmitter & holding register to empty
1356  */
1357 static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up)
1358 {
1359         unsigned int status, tmout = 10000;
1360
1361         /* Wait up to 10ms for the character(s) to be sent. */
1362         do {
1363                 status = serial_in(up, UART_LSR);
1364
1365                 if (status & UART_LSR_BI)
1366                         up->lsr_break_flag = UART_LSR_BI;
1367
1368                 if (--tmout == 0)
1369                         break;
1370                 udelay(1);
1371         } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
1372
1373         /* Wait up to 1s for flow control if necessary */
1374         if (up->port.flags & ASYNC_CONS_FLOW) {
1375                 tmout = 1000000;
1376                 while (--tmout &&
1377                        ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
1378                         udelay(1);
1379         }
1380 }
1381
1382 /*
1383  *      Print a string to the serial port trying not to disturb
1384  *      any possible real use of the port...
1385  */
1386 static void sunsu_console_write(struct console *co, const char *s,
1387                                 unsigned int count)
1388 {
1389         struct uart_sunsu_port *up = &sunsu_ports[co->index];
1390         unsigned int ier;
1391         int i;
1392
1393         /*
1394          *      First save the UER then disable the interrupts
1395          */
1396         ier = serial_in(up, UART_IER);
1397         serial_out(up, UART_IER, 0);
1398
1399         /*
1400          *      Now, do each character
1401          */
1402         for (i = 0; i < count; i++, s++) {
1403                 wait_for_xmitr(up);
1404
1405                 /*
1406                  *      Send the character out.
1407                  *      If a LF, also do CR...
1408                  */
1409                 serial_out(up, UART_TX, *s);
1410                 if (*s == 10) {
1411                         wait_for_xmitr(up);
1412                         serial_out(up, UART_TX, 13);
1413                 }
1414         }
1415
1416         /*
1417          *      Finally, wait for transmitter to become empty
1418          *      and restore the IER
1419          */
1420         wait_for_xmitr(up);
1421         serial_out(up, UART_IER, ier);
1422 }
1423
1424 /*
1425  *      Setup initial baud/bits/parity. We do two things here:
1426  *      - construct a cflag setting for the first su_open()
1427  *      - initialize the serial port
1428  *      Return non-zero if we didn't find a serial port.
1429  */
1430 static int __init sunsu_console_setup(struct console *co, char *options)
1431 {
1432         struct uart_port *port;
1433         int baud = 9600;
1434         int bits = 8;
1435         int parity = 'n';
1436         int flow = 'n';
1437
1438         printk("Console: ttyS%d (SU)\n",
1439                (sunsu_reg.minor - 64) + co->index);
1440
1441         /*
1442          * Check whether an invalid uart number has been specified, and
1443          * if so, search for the first available port that does have
1444          * console support.
1445          */
1446         if (co->index >= UART_NR)
1447                 co->index = 0;
1448         port = &sunsu_ports[co->index].port;
1449
1450         /*
1451          * Temporary fix.
1452          */
1453         spin_lock_init(&port->lock);
1454
1455         if (options)
1456                 uart_parse_options(options, &baud, &parity, &bits, &flow);
1457
1458         return uart_set_options(port, co, baud, parity, bits, flow);
1459 }
1460
1461 static struct console sunsu_cons = {
1462         .name   =       "ttyS",
1463         .write  =       sunsu_console_write,
1464         .device =       uart_console_device,
1465         .setup  =       sunsu_console_setup,
1466         .flags  =       CON_PRINTBUFFER,
1467         .index  =       -1,
1468         .data   =       &sunsu_reg,
1469 };
1470 #define SUNSU_CONSOLE   (&sunsu_cons)
1471
1472 /*
1473  *      Register console.
1474  */
1475
1476 static int __init sunsu_serial_console_init(void)
1477 {
1478         int i;
1479
1480         if (con_is_present())
1481                 return 0;
1482
1483         for (i = 0; i < UART_NR; i++) {
1484                 int this_minor = sunsu_reg.minor + i;
1485
1486                 if ((this_minor - 64) == (serial_console - 1))
1487                         break;
1488         }
1489         if (i == UART_NR)
1490                 return 0;
1491         if (sunsu_ports[i].port_node == 0)
1492                 return 0;
1493
1494         sunsu_cons.index = i;
1495         register_console(&sunsu_cons);
1496         return 0;
1497 }
1498 #else
1499 #define SUNSU_CONSOLE                   (NULL)
1500 #define sunsu_serial_console_init()     do { } while (0)
1501 #endif
1502
1503 static int __init sunsu_serial_init(void)
1504 {
1505         int instance, ret, i;
1506
1507         /* How many instances do we need?  */
1508         instance = 0;
1509         for (i = 0; i < UART_NR; i++) {
1510                 struct uart_sunsu_port *up = &sunsu_ports[i];
1511
1512                 if (up->su_type == SU_PORT_MS ||
1513                     up->su_type == SU_PORT_KBD)
1514                         continue;
1515
1516                 up->port.flags |= ASYNC_BOOT_AUTOCONF;
1517                 up->port.type = PORT_UNKNOWN;
1518                 up->port.uartclk = (SU_BASE_BAUD * 16);
1519
1520                 sunsu_autoconfig(up);
1521                 if (up->port.type == PORT_UNKNOWN)
1522                         continue;
1523
1524                 up->port.line = instance++;
1525                 up->port.ops = &sunsu_pops;
1526         }
1527
1528         sunsu_reg.minor = sunserial_current_minor;
1529         sunserial_current_minor += instance;
1530
1531         sunsu_reg.nr = instance;
1532         sunsu_reg.cons = SUNSU_CONSOLE;
1533
1534         ret = uart_register_driver(&sunsu_reg);
1535         if (ret < 0)
1536                 return ret;
1537
1538         sunsu_serial_console_init();
1539         for (i = 0; i < UART_NR; i++) {
1540                 struct uart_sunsu_port *up = &sunsu_ports[i];
1541
1542                 /* Do not register Keyboard/Mouse lines with UART
1543                  * layer.
1544                  */
1545                 if (up->su_type == SU_PORT_MS ||
1546                     up->su_type == SU_PORT_KBD)
1547                         continue;
1548
1549                 if (up->port.type == PORT_UNKNOWN)
1550                         continue;
1551
1552                 uart_add_one_port(&sunsu_reg, &up->port);
1553         }
1554
1555         return 0;
1556 }
1557
1558 static int su_node_ok(int node, char *name, int namelen)
1559 {
1560         if (strncmp(name, "su", namelen) == 0 ||
1561             strncmp(name, "su_pnp", namelen) == 0)
1562                 return 1;
1563
1564         if (strncmp(name, "serial", namelen) == 0) {
1565                 char compat[32];
1566                 int clen;
1567
1568                 /* Is it _really_ a 'su' device? */
1569                 clen = prom_getproperty(node, "compatible", compat, sizeof(compat));
1570                 if (clen > 0) {
1571                         if (strncmp(compat, "sab82532", 8) == 0) {
1572                                 /* Nope, Siemens serial, not for us. */
1573                                 return 0;
1574                         }
1575                 }
1576                 return 1;
1577         }
1578
1579         return 0;
1580 }
1581
1582 #define SU_PROPSIZE     128
1583
1584 /*
1585  * Scan status structure.
1586  * "prop" is a local variable but it eats stack to keep it in each
1587  * stack frame of a recursive procedure.
1588  */
1589 struct su_probe_scan {
1590         int msnode, kbnode;     /* PROM nodes for mouse and keyboard */
1591         int msx, kbx;           /* minors for mouse and keyboard */
1592         int devices;            /* scan index */
1593         char prop[SU_PROPSIZE];
1594 };
1595
1596 /*
1597  * We have several platforms which present 'su' in different parts
1598  * of the device tree. 'su' may be found under obio, ebus, isa and pci.
1599  * We walk over the tree and find them wherever PROM hides them.
1600  */
1601 static void __init su_probe_any(struct su_probe_scan *t, int sunode)
1602 {
1603         struct uart_sunsu_port *up;
1604         int len;
1605
1606         if (t->devices >= UART_NR)
1607                 return;
1608
1609         for (; sunode != 0; sunode = prom_getsibling(sunode)) {
1610                 len = prom_getproperty(sunode, "name", t->prop, SU_PROPSIZE);
1611                 if (len <= 1)
1612                         continue;               /* Broken PROM node */
1613
1614                 if (su_node_ok(sunode, t->prop, len)) {
1615                         up = &sunsu_ports[t->devices];
1616                         if (t->kbnode != 0 && sunode == t->kbnode) {
1617                                 t->kbx = t->devices;
1618                                 up->su_type = SU_PORT_KBD;
1619                         } else if (t->msnode != 0 && sunode == t->msnode) {
1620                                 t->msx = t->devices;
1621                                 up->su_type = SU_PORT_MS;
1622                         } else {
1623 #ifdef CONFIG_SPARC64
1624                                 /*
1625                                  * Do not attempt to use the truncated
1626                                  * keyboard/mouse ports as serial ports
1627                                  * on Ultras with PC keyboard attached.
1628                                  */
1629                                 if (prom_getbool(sunode, "mouse"))
1630                                         continue;
1631                                 if (prom_getbool(sunode, "keyboard"))
1632                                         continue;
1633 #endif
1634                                 up->su_type = SU_PORT_PORT;
1635                         }
1636                         up->port_node = sunode;
1637                         ++t->devices;
1638                 } else {
1639                         su_probe_any(t, prom_getchild(sunode));
1640                 }
1641         }
1642 }
1643
1644 static int __init sunsu_probe(void)
1645 {
1646         int node;
1647         int len;
1648         struct su_probe_scan scan;
1649
1650         /*
1651          * First, we scan the tree.
1652          */
1653         scan.devices = 0;
1654         scan.msx = -1;
1655         scan.kbx = -1;
1656         scan.kbnode = 0;
1657         scan.msnode = 0;
1658
1659         /*
1660          * Get the nodes for keyboard and mouse from 'aliases'...
1661          */
1662         node = prom_getchild(prom_root_node);
1663         node = prom_searchsiblings(node, "aliases");
1664         if (node != 0) {
1665                 len = prom_getproperty(node, "keyboard", scan.prop, SU_PROPSIZE);
1666                 if (len > 0) {
1667                         scan.prop[len] = 0;
1668                         scan.kbnode = prom_finddevice(scan.prop);
1669                 }
1670
1671                 len = prom_getproperty(node, "mouse", scan.prop, SU_PROPSIZE);
1672                 if (len > 0) {
1673                         scan.prop[len] = 0;
1674                         scan.msnode = prom_finddevice(scan.prop);
1675                 }
1676         }
1677
1678         su_probe_any(&scan, prom_getchild(prom_root_node));
1679
1680         /*
1681          * Second, we process the special case of keyboard and mouse.
1682          *
1683          * Currently if we got keyboard and mouse hooked to "su" ports
1684          * we do not use any possible remaining "su" as a serial port.
1685          * Thus, we ignore values of .msx and .kbx, then compact ports.
1686          */
1687         if (scan.msx != -1 && scan.kbx != -1) {
1688                 sunsu_ports[0].su_type = SU_PORT_MS;
1689                 sunsu_ports[0].port_node = scan.msnode;
1690                 sunsu_kbd_ms_init(&sunsu_ports[0], 0);
1691
1692                 sunsu_ports[1].su_type = SU_PORT_KBD;
1693                 sunsu_ports[1].port_node = scan.kbnode;
1694                 sunsu_kbd_ms_init(&sunsu_ports[1], 1);
1695
1696                 return 0;
1697         }
1698
1699         if (scan.msx != -1 || scan.kbx != -1) {
1700                 printk("sunsu_probe: cannot match keyboard and mouse, confused\n");
1701                 return -ENODEV;
1702         }
1703
1704         if (scan.devices == 0)
1705                 return -ENODEV;
1706
1707         /*
1708          * Console must be initiated after the generic initialization.
1709          */
1710         sunsu_serial_init();
1711
1712         return 0;
1713 }
1714
1715 static void __exit sunsu_exit(void)
1716 {
1717         int i, saw_uart;
1718
1719         saw_uart = 0;
1720         for (i = 0; i < UART_NR; i++) {
1721                 struct uart_sunsu_port *up = &sunsu_ports[i];
1722
1723                 if (up->su_type == SU_PORT_MS ||
1724                     up->su_type == SU_PORT_KBD) {
1725 #ifdef CONFIG_SERIO
1726                         if (up->serio) {
1727                                 serio_unregister_port(up->serio);
1728                                 up->serio = NULL;
1729                         }
1730 #endif
1731                 } else if (up->port.type != PORT_UNKNOWN) {
1732                         uart_remove_one_port(&sunsu_reg, &up->port);
1733                         saw_uart++;
1734                 }
1735         }
1736
1737         if (saw_uart)
1738                 uart_unregister_driver(&sunsu_reg);
1739 }
1740
1741 module_init(sunsu_probe);
1742 module_exit(sunsu_exit);