2 # Touchscreen driver configuration
4 menuconfig INPUT_TOUCHSCREEN
7 Say Y here, and a list of supported touchscreens will be displayed.
8 This option doesn't affect the kernel.
14 config TOUCHSCREEN_88PM860X
15 tristate "Marvell 88PM860x touchscreen"
16 depends on MFD_88PM860X
18 Say Y here if you have a 88PM860x PMIC and want to enable
19 support for the built-in touchscreen.
23 To compile this driver as a module, choose M here: the
24 module will be called 88pm860x-ts.
26 config TOUCHSCREEN_ADS7846
27 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
29 depends on HWMON = n || HWMON
31 Say Y here if you have a touchscreen interface using the
32 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
33 and your board-specific setup code includes that in its
36 If HWMON is selected, and the driver is told the reference voltage
37 on your board, you will also get hwmon interfaces for the voltage
38 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
40 If unsure, say N (but it's safe to say "Y").
42 To compile this driver as a module, choose M here: the
43 module will be called ads7846.
45 config TOUCHSCREEN_AD7877
46 tristate "AD7877 based touchscreens"
49 Say Y here if you have a touchscreen interface using the
50 AD7877 controller, and your board-specific initialization
51 code includes that in its table of SPI devices.
53 If unsure, say N (but it's safe to say "Y").
55 To compile this driver as a module, choose M here: the
56 module will be called ad7877.
58 config TOUCHSCREEN_AD7879
59 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
61 Say Y here if you want to support a touchscreen interface using
62 the AD7879-1/AD7889-1 controller.
64 You should select a bus connection too.
66 To compile this driver as a module, choose M here: the
67 module will be called ad7879.
69 config TOUCHSCREEN_AD7879_I2C
70 tristate "support I2C bus connection"
71 depends on TOUCHSCREEN_AD7879 && I2C
73 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
75 To compile this driver as a module, choose M here: the
76 module will be called ad7879-i2c.
78 config TOUCHSCREEN_AD7879_SPI
79 tristate "support SPI bus connection"
80 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
82 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
84 If unsure, say N (but it's safe to say "Y").
86 To compile this driver as a module, choose M here: the
87 module will be called ad7879-spi.
89 config TOUCHSCREEN_ATMEL_MXT
90 tristate "Atmel mXT I2C Touchscreen"
93 Say Y here if you have Atmel mXT series I2C touchscreen,
94 such as AT42QT602240/ATMXT224, connected to your system.
98 To compile this driver as a module, choose M here: the
99 module will be called atmel_mxt_ts.
101 config TOUCHSCREEN_AUO_PIXCIR
102 tristate "AUO in-cell touchscreen using Pixcir ICs"
106 Say Y here if you have a AUO display with in-cell touchscreen
111 To compile this driver as a module, choose M here: the
112 module will be called auo-pixcir-ts.
114 config TOUCHSCREEN_BITSY
115 tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
116 depends on SA1100_BITSY
119 Say Y here if you have the h3600 (Bitsy) touchscreen.
123 To compile this driver as a module, choose M here: the
124 module will be called h3600_ts_input.
126 config TOUCHSCREEN_BU21013
127 tristate "BU21013 based touch panel controllers"
130 Say Y here if you have a bu21013 touchscreen connected to
135 To compile this driver as a module, choose M here: the
136 module will be called bu21013_ts.
138 config TOUCHSCREEN_CY8CTMG110
139 tristate "cy8ctmg110 touchscreen"
144 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
149 To compile this driver as a module, choose M here: the
150 module will be called cy8ctmg110_ts.
152 config TOUCHSCREEN_DA9034
153 tristate "Touchscreen support for Dialog Semiconductor DA9034"
154 depends on PMIC_DA903X
157 Say Y here to enable the support for the touchscreen found
158 on Dialog Semiconductor DA9034 PMIC.
160 config TOUCHSCREEN_DYNAPRO
161 tristate "Dynapro serial touchscreen"
164 Say Y here if you have a Dynapro serial touchscreen connected to
169 To compile this driver as a module, choose M here: the
170 module will be called dynapro.
172 config TOUCHSCREEN_HAMPSHIRE
173 tristate "Hampshire serial touchscreen"
176 Say Y here if you have a Hampshire serial touchscreen connected to
181 To compile this driver as a module, choose M here: the
182 module will be called hampshire.
184 config TOUCHSCREEN_EETI
185 tristate "EETI touchscreen panel support"
188 Say Y here to enable support for I2C connected EETI touch panels.
190 To compile this driver as a module, choose M here: the
191 module will be called eeti_ts.
193 config TOUCHSCREEN_EGALAX
194 tristate "EETI eGalax multi-touch panel support"
197 Say Y here to enable support for I2C connected EETI
198 eGalax multi-touch panels.
200 To compile this driver as a module, choose M here: the
201 module will be called egalax_ts.
203 config TOUCHSCREEN_FUJITSU
204 tristate "Fujitsu serial touchscreen"
207 Say Y here if you have the Fujitsu touchscreen (such as one
208 installed in Lifebook P series laptop) connected to your
213 To compile this driver as a module, choose M here: the
214 module will be called fujitsu-ts.
216 config TOUCHSCREEN_S3C2410
217 tristate "Samsung S3C2410/generic touchscreen input driver"
218 depends on ARCH_S3C2410 || SAMSUNG_DEV_TS
221 Say Y here if you have the s3c2410 touchscreen.
225 To compile this driver as a module, choose M here: the
226 module will be called s3c2410_ts.
228 config TOUCHSCREEN_GUNZE
229 tristate "Gunze AHL-51S touchscreen"
232 Say Y here if you have the Gunze AHL-51 touchscreen connected to
237 To compile this driver as a module, choose M here: the
238 module will be called gunze.
240 config TOUCHSCREEN_ELO
241 tristate "Elo serial touchscreens"
244 Say Y here if you have an Elo serial touchscreen connected to
249 To compile this driver as a module, choose M here: the
250 module will be called elo.
252 config TOUCHSCREEN_ELOUSB
253 tristate "Elo USB touchscreens"
256 Say Y here if you have an Elo USB touchscreen connected to
261 To compile this driver as a module, choose M here: the
262 module will be called elousb.
264 config TOUCHSCREEN_WACOM_W8001
265 tristate "Wacom W8001 penabled serial touchscreen"
268 Say Y here if you have an Wacom W8001 penabled serial touchscreen
269 connected to your system.
273 To compile this driver as a module, choose M here: the
274 module will be called wacom_w8001.
276 config TOUCHSCREEN_LPC32XX
277 tristate "LPC32XX touchscreen controller"
278 depends on ARCH_LPC32XX
280 Say Y here if you have a LPC32XX device and want
281 to support the built-in touchscreen.
283 To compile this driver as a module, choose M here: the
284 module will be called lpc32xx_ts.
286 config TOUCHSCREEN_MAX11801
287 tristate "MAX11801 based touchscreens"
290 Say Y here if you have a MAX11801 based touchscreen
295 To compile this driver as a module, choose M here: the
296 module will be called max11801_ts.
298 config TOUCHSCREEN_MCS5000
299 tristate "MELFAS MCS-5000 touchscreen"
302 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
307 To compile this driver as a module, choose M here: the
308 module will be called mcs5000_ts.
310 config TOUCHSCREEN_MTOUCH
311 tristate "MicroTouch serial touchscreens"
314 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
319 To compile this driver as a module, choose M here: the
320 module will be called mtouch.
322 config TOUCHSCREEN_INEXIO
323 tristate "iNexio serial touchscreens"
326 Say Y here if you have an iNexio serial touchscreen connected to
331 To compile this driver as a module, choose M here: the
332 module will be called inexio.
334 config TOUCHSCREEN_INTEL_MID
335 tristate "Intel MID platform resistive touchscreen"
336 depends on INTEL_SCU_IPC
338 Say Y here if you have a Intel MID based touchscreen in
343 To compile this driver as a module, choose M here: the
344 module will be called intel_mid_touch.
346 config TOUCHSCREEN_MK712
347 tristate "ICS MicroClock MK712 touchscreen"
349 Say Y here if you have the ICS MicroClock MK712 touchscreen
350 controller chip in your system.
354 To compile this driver as a module, choose M here: the
355 module will be called mk712.
357 config TOUCHSCREEN_HP600
358 tristate "HP Jornada 6xx touchscreen"
359 depends on SH_HP6XX && SH_ADC
361 Say Y here if you have a HP Jornada 620/660/680/690 and want to
362 support the built-in touchscreen.
364 To compile this driver as a module, choose M here: the
365 module will be called hp680_ts_input.
367 config TOUCHSCREEN_HP7XX
368 tristate "HP Jornada 7xx touchscreen"
369 depends on SA1100_JORNADA720_SSP
371 Say Y here if you have a HP Jornada 710/720/728 and want
372 to support the built-in touchscreen.
374 To compile this driver as a module, choose M here: the
375 module will be called jornada720_ts.
377 config TOUCHSCREEN_HTCPEN
378 tristate "HTC Shift X9500 touchscreen"
381 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
382 Clio / Shangrila and want to support the built-in touchscreen.
386 To compile this driver as a module, choose M here: the
387 module will be called htcpen.
389 config TOUCHSCREEN_PENMOUNT
390 tristate "Penmount serial touchscreen"
393 Say Y here if you have a Penmount serial touchscreen connected to
398 To compile this driver as a module, choose M here: the
399 module will be called penmount.
401 config TOUCHSCREEN_MIGOR
402 tristate "Renesas MIGO-R touchscreen"
403 depends on SH_MIGOR && I2C
405 Say Y here to enable MIGO-R touchscreen support.
409 To compile this driver as a module, choose M here: the
410 module will be called migor_ts.
412 config TOUCHSCREEN_TNETV107X
413 tristate "TI TNETV107X touchscreen support"
414 depends on ARCH_DAVINCI_TNETV107X
416 Say Y here if you want to use the TNETV107X touchscreen.
418 To compile this driver as a module, choose M here: the
419 module will be called tnetv107x-ts.
421 config TOUCHSCREEN_TOUCHRIGHT
422 tristate "Touchright serial touchscreen"
425 Say Y here if you have a Touchright serial touchscreen connected to
430 To compile this driver as a module, choose M here: the
431 module will be called touchright.
433 config TOUCHSCREEN_TOUCHWIN
434 tristate "Touchwin serial touchscreen"
437 Say Y here if you have a Touchwin serial touchscreen connected to
442 To compile this driver as a module, choose M here: the
443 module will be called touchwin.
445 config TOUCHSCREEN_ATMEL_TSADCC
446 tristate "Atmel Touchscreen Interface"
447 depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
449 Say Y here if you have a 4-wire touchscreen connected to the
450 ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
454 To compile this driver as a module, choose M here: the
455 module will be called atmel_tsadcc.
457 config TOUCHSCREEN_UCB1400
458 tristate "Philips UCB1400 touchscreen"
460 depends on UCB1400_CORE
462 This enables support for the Philips UCB1400 touchscreen interface.
463 The UCB1400 is an AC97 audio codec. The touchscreen interface
464 will be initialized only after the ALSA subsystem has been
465 brought up and the UCB1400 detected. You therefore have to
466 configure ALSA support as well (either built-in or modular,
467 independently of whether this driver is itself built-in or
468 modular) for this driver to work.
470 To compile this driver as a module, choose M here: the
471 module will be called ucb1400_ts.
473 config TOUCHSCREEN_PIXCIR
474 tristate "PIXCIR I2C touchscreens"
477 Say Y here if you have a pixcir i2c touchscreen
482 To compile this driver as a module, choose M here: the
483 module will be called pixcir_i2c_ts.
485 config TOUCHSCREEN_WM831X
486 tristate "Support for WM831x touchscreen controllers"
487 depends on MFD_WM831X
489 This enables support for the touchscreen controller on the WM831x
492 To compile this driver as a module, choose M here: the
493 module will be called wm831x-ts.
495 config TOUCHSCREEN_WM97XX
496 tristate "Support for WM97xx AC97 touchscreen controllers"
499 Say Y here if you have a Wolfson Microelectronics WM97xx
500 touchscreen connected to your system. Note that this option
501 only enables core driver, you will also need to select
502 support for appropriate chip below.
506 To compile this driver as a module, choose M here: the
507 module will be called wm97xx-ts.
509 config TOUCHSCREEN_WM9705
510 bool "WM9705 Touchscreen interface support"
511 depends on TOUCHSCREEN_WM97XX
514 Say Y here to enable support for the Wolfson Microelectronics
515 WM9705 touchscreen controller.
517 config TOUCHSCREEN_WM9712
518 bool "WM9712 Touchscreen interface support"
519 depends on TOUCHSCREEN_WM97XX
522 Say Y here to enable support for the Wolfson Microelectronics
523 WM9712 touchscreen controller.
525 config TOUCHSCREEN_WM9713
526 bool "WM9713 Touchscreen interface support"
527 depends on TOUCHSCREEN_WM97XX
530 Say Y here to enable support for the Wolfson Microelectronics
531 WM9713 touchscreen controller.
533 config TOUCHSCREEN_WM97XX_ATMEL
534 tristate "WM97xx Atmel accelerated touch"
535 depends on TOUCHSCREEN_WM97XX && (AVR32 || ARCH_AT91)
537 Say Y here for support for streaming mode with WM97xx touchscreens
538 on Atmel AT91 or AVR32 systems with an AC97C module.
540 Be aware that this will use channel B in the controller for
541 streaming data, this must not conflict with other AC97C drivers.
545 To compile this driver as a module, choose M here: the module will
546 be called atmel-wm97xx.
548 config TOUCHSCREEN_WM97XX_MAINSTONE
549 tristate "WM97xx Mainstone/Palm accelerated touch"
550 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
552 Say Y here for support for streaming mode with WM97xx touchscreens
553 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
557 To compile this driver as a module, choose M here: the
558 module will be called mainstone-wm97xx.
560 config TOUCHSCREEN_WM97XX_ZYLONITE
561 tristate "Zylonite accelerated touch"
562 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
563 select TOUCHSCREEN_WM9713
565 Say Y here for support for streaming mode with the touchscreen
570 To compile this driver as a module, choose M here: the
571 module will be called zylonite-wm97xx.
573 config TOUCHSCREEN_USB_COMPOSITE
574 tristate "USB Touchscreen Driver"
575 depends on USB_ARCH_HAS_HCD
578 USB Touchscreen driver for:
579 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
580 - PanJit TouchSet USB
581 - 3M MicroTouch USB (EX II series)
583 - some other eTurboTouch
586 - IRTOUCHSYSTEMS/UNITOP
588 - GoTop Super_Q2/GogoPen/PenPower tablets
589 - JASTEC USB Touch Controller/DigiTech DTR-02U
590 - Zytronic controllers
591 - Elo TouchSystems 2700 IntelliTouch
593 Have a look at <http://linux.chapter7.ch/touchkit/> for
594 a usage description and the required user-space stuff.
596 To compile this driver as a module, choose M here: the
597 module will be called usbtouchscreen.
599 config TOUCHSCREEN_MC13783
600 tristate "Freescale MC13783 touchscreen input driver"
601 depends on MFD_MC13783
603 Say Y here if you have an Freescale MC13783 PMIC on your
604 board and want to use its touchscreen
608 To compile this driver as a module, choose M here: the
609 module will be called mc13783_ts.
611 config TOUCHSCREEN_USB_EGALAX
613 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
614 depends on TOUCHSCREEN_USB_COMPOSITE
616 config TOUCHSCREEN_USB_PANJIT
618 bool "PanJit device support" if EXPERT
619 depends on TOUCHSCREEN_USB_COMPOSITE
621 config TOUCHSCREEN_USB_3M
623 bool "3M/Microtouch EX II series device support" if EXPERT
624 depends on TOUCHSCREEN_USB_COMPOSITE
626 config TOUCHSCREEN_USB_ITM
628 bool "ITM device support" if EXPERT
629 depends on TOUCHSCREEN_USB_COMPOSITE
631 config TOUCHSCREEN_USB_ETURBO
633 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
634 depends on TOUCHSCREEN_USB_COMPOSITE
636 config TOUCHSCREEN_USB_GUNZE
638 bool "Gunze AHL61 device support" if EXPERT
639 depends on TOUCHSCREEN_USB_COMPOSITE
641 config TOUCHSCREEN_USB_DMC_TSC10
643 bool "DMC TSC-10/25 device support" if EXPERT
644 depends on TOUCHSCREEN_USB_COMPOSITE
646 config TOUCHSCREEN_USB_IRTOUCH
648 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
649 depends on TOUCHSCREEN_USB_COMPOSITE
651 config TOUCHSCREEN_USB_IDEALTEK
653 bool "IdealTEK URTC1000 device support" if EXPERT
654 depends on TOUCHSCREEN_USB_COMPOSITE
656 config TOUCHSCREEN_USB_GENERAL_TOUCH
658 bool "GeneralTouch Touchscreen device support" if EXPERT
659 depends on TOUCHSCREEN_USB_COMPOSITE
661 config TOUCHSCREEN_USB_GOTOP
663 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
664 depends on TOUCHSCREEN_USB_COMPOSITE
666 config TOUCHSCREEN_USB_JASTEC
668 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
669 depends on TOUCHSCREEN_USB_COMPOSITE
671 config TOUCHSCREEN_USB_ELO
673 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
674 depends on TOUCHSCREEN_USB_COMPOSITE
676 config TOUCHSCREEN_USB_E2I
678 bool "e2i Touchscreen controller (e.g. from Mimo 740)"
679 depends on TOUCHSCREEN_USB_COMPOSITE
681 config TOUCHSCREEN_USB_ZYTRONIC
683 bool "Zytronic controller" if EXPERT
684 depends on TOUCHSCREEN_USB_COMPOSITE
686 config TOUCHSCREEN_USB_ETT_TC45USB
688 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
689 depends on TOUCHSCREEN_USB_COMPOSITE
691 config TOUCHSCREEN_USB_NEXIO
693 bool "NEXIO/iNexio device support" if EXPERT
694 depends on TOUCHSCREEN_USB_COMPOSITE
696 config TOUCHSCREEN_TOUCHIT213
697 tristate "Sahara TouchIT-213 touchscreen"
700 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
704 To compile this driver as a module, choose M here: the
705 module will be called touchit213.
707 config TOUCHSCREEN_TSC_SERIO
708 tristate "TSC-10/25/40 serial touchscreen support"
711 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
716 To compile this driver as a module, choose M here: the
717 module will be called tsc40.
719 config TOUCHSCREEN_TSC2005
720 tristate "TSC2005 based touchscreens"
721 depends on SPI_MASTER && GENERIC_HARDIRQS
723 Say Y here if you have a TSC2005 based touchscreen.
727 To compile this driver as a module, choose M here: the
728 module will be called tsc2005.
730 config TOUCHSCREEN_TSC2007
731 tristate "TSC2007 based touchscreens"
734 Say Y here if you have a TSC2007 based touchscreen.
738 To compile this driver as a module, choose M here: the
739 module will be called tsc2007.
741 config TOUCHSCREEN_W90X900
742 tristate "W90P910 touchscreen driver"
745 Say Y here if you have a W90P910 based touchscreen.
747 To compile this driver as a module, choose M here: the
748 module will be called w90p910_ts.
750 config TOUCHSCREEN_PCAP
751 tristate "Motorola PCAP touchscreen"
754 Say Y here if you have a Motorola EZX telephone and
755 want to enable support for the built-in touchscreen.
757 To compile this driver as a module, choose M here: the
758 module will be called pcap_ts.
760 config TOUCHSCREEN_ST1232
761 tristate "Sitronix ST1232 touchscreen controllers"
764 Say Y here if you want to support Sitronix ST1232
765 touchscreen controller.
769 To compile this driver as a module, choose M here: the
770 module will be called st1232_ts.
772 config TOUCHSCREEN_STMPE
773 tristate "STMicroelectronics STMPE touchscreens"
776 Say Y here if you want support for STMicroelectronics
777 STMPE touchscreen controllers.
779 To compile this driver as a module, choose M here: the
780 module will be called stmpe-ts.
782 config TOUCHSCREEN_TPS6507X
783 tristate "TPS6507x based touchscreens"
786 Say Y here if you have a TPS6507x based touchscreen
791 To compile this driver as a module, choose M here: the
792 module will be called tps6507x_ts.