drivers/mmc/au1xmmc.c

   1 /*
   2  * linux/drivers/mmc/au1xmmc.c - AU1XX0 MMC driver
   3  *
   4  *  Copyright (c) 2005, Advanced Micro Devices, Inc.
   5  *
   6  *  Developed with help from the 2.4.30 MMC AU1XXX controller including
   7  *  the following copyright notices:
   8  *     Copyright (c) 2003-2004 Embedded Edge, LLC.
   9  *     Portions Copyright (C) 2002 Embedix, Inc
  10  *     Copyright 2002 Hewlett-Packard Company
  11
  12  *  2.6 version of this driver inspired by:
  13  *     (drivers/mmc/wbsd.c) Copyright (C) 2004-2005 Pierre Ossman,
  14  *     All Rights Reserved.
  15  *     (drivers/mmc/pxa.c) Copyright (C) 2003 Russell King,
  16  *     All Rights Reserved.
  17  *
  18
  19  * This program is free software; you can redistribute it and/or modify
  20  * it under the terms of the GNU General Public License version 2 as
  21  * published by the Free Software Foundation.
  22  */
  23
  24 /* Why is a timer used to detect insert events?
  25  *
  26  * From the AU1100 MMC application guide:
  27  * If the Au1100-based design is intended to support both MultiMediaCards
  28  * and 1- or 4-data bit SecureDigital cards, then the solution is to
  29  * connect a weak (560KOhm) pull-up resistor to connector pin 1.
  30  * In doing so, a MMC card never enters SPI-mode communications,
  31  * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective
  32  * (the low to high transition will not occur).
  33  *
  34  * So we use the timer to check the status manually.
  35  */
  36
  37 #include <linux/module.h>
  38 #include <linux/init.h>
  39 #include <linux/platform_device.h>
  40 #include <linux/mm.h>
  41 #include <linux/interrupt.h>
  42 #include <linux/dma-mapping.h>
  43
  44 #include <linux/mmc/host.h>
  45 #include <linux/mmc/protocol.h>
  46 #include <asm/io.h>
  47 #include <asm/mach-au1x00/au1000.h>
  48 #include <asm/mach-au1x00/au1xxx_dbdma.h>
  49 #include <asm/mach-au1x00/au1100_mmc.h>
  50 #include <asm/scatterlist.h>
  51
  52 #include <au1xxx.h>
  53 #include "au1xmmc.h"
  54
  55 #define DRIVER_NAME "au1xxx-mmc"
  56
  57 /* Set this to enable special debugging macros */
  58
  59 #ifdef DEBUG
  60 #define DBG(fmt, idx, args...) printk("au1xx(%d): DEBUG: " fmt, idx, ##args)
  61 #else
  62 #define DBG(fmt, idx, args...)
  63 #endif
  64
  65 const struct {
  66         u32 iobase;
  67         u32 tx_devid, rx_devid;
  68         u16 bcsrpwr;
  69         u16 bcsrstatus;
  70         u16 wpstatus;
  71 } au1xmmc_card_table[] = {
  72         { SD0_BASE, DSCR_CMD0_SDMS_TX0, DSCR_CMD0_SDMS_RX0,
  73           BCSR_BOARD_SD0PWR, BCSR_INT_SD0INSERT, BCSR_STATUS_SD0WP },
  74 #ifndef CONFIG_MIPS_DB1200
  75         { SD1_BASE, DSCR_CMD0_SDMS_TX1, DSCR_CMD0_SDMS_RX1,
  76           BCSR_BOARD_DS1PWR, BCSR_INT_SD1INSERT, BCSR_STATUS_SD1WP }
  77 #endif
  78 };
  79
  80 #define AU1XMMC_CONTROLLER_COUNT \
  81         (sizeof(au1xmmc_card_table) / sizeof(au1xmmc_card_table[0]))
  82
  83 /* This array stores pointers for the hosts (used by the IRQ handler) */
  84 struct au1xmmc_host *au1xmmc_hosts[AU1XMMC_CONTROLLER_COUNT];
  85 static int dma = 1;
  86
  87 #ifdef MODULE
  88 module_param(dma, bool, 0);
  89 MODULE_PARM_DESC(dma, "Use DMA engine for data transfers (0 = disabled)");
  90 #endif
  91
  92 static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask)
  93 {
  94         u32 val = au_readl(HOST_CONFIG(host));
  95         val |= mask;
  96         au_writel(val, HOST_CONFIG(host));
  97         au_sync();
  98 }
  99
 100 static inline void FLUSH_FIFO(struct au1xmmc_host *host)
 101 {
 102         u32 val = au_readl(HOST_CONFIG2(host));
 103
 104         au_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host));
 105         au_sync_delay(1);
 106
 107         /* SEND_STOP will turn off clock control - this re-enables it */
 108         val &= ~SD_CONFIG2_DF;
 109
 110         au_writel(val, HOST_CONFIG2(host));
 111         au_sync();
 112 }
 113
 114 static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask)
 115 {
 116         u32 val = au_readl(HOST_CONFIG(host));
 117         val &= ~mask;
 118         au_writel(val, HOST_CONFIG(host));
 119         au_sync();
 120 }
 121
 122 static inline void SEND_STOP(struct au1xmmc_host *host)
 123 {
 124
 125         /* We know the value of CONFIG2, so avoid a read we don't need */
 126         u32 mask = SD_CONFIG2_EN;
 127
 128         WARN_ON(host->status != HOST_S_DATA);
 129         host->status = HOST_S_STOP;
 130
 131         au_writel(mask | SD_CONFIG2_DF, HOST_CONFIG2(host));
 132         au_sync();
 133
 134         /* Send the stop commmand */
 135         au_writel(STOP_CMD, HOST_CMD(host));
 136 }
 137
 138 static void au1xmmc_set_power(struct au1xmmc_host *host, int state)
 139 {
 140
 141         u32 val = au1xmmc_card_table[host->id].bcsrpwr;
 142
 143         bcsr->board &= ~val;
 144         if (state) bcsr->board |= val;
 145
 146         au_sync_delay(1);
 147 }
 148
 149 static inline int au1xmmc_card_inserted(struct au1xmmc_host *host)
 150 {
 151         return (bcsr->sig_status & au1xmmc_card_table[host->id].bcsrstatus)
 152                 ? 1 : 0;
 153 }
 154
 155 static int au1xmmc_card_readonly(struct mmc_host *mmc)
 156 {
 157         struct au1xmmc_host *host = mmc_priv(mmc);
 158         return (bcsr->status & au1xmmc_card_table[host->id].wpstatus)
 159                 ? 1 : 0;
 160 }
 161
 162 static void au1xmmc_finish_request(struct au1xmmc_host *host)
 163 {
 164
 165         struct mmc_request *mrq = host->mrq;
 166
 167         host->mrq = NULL;
 168         host->flags &= HOST_F_ACTIVE;
 169
 170         host->dma.len = 0;
 171         host->dma.dir = 0;
 172
 173         host->pio.index  = 0;
 174         host->pio.offset = 0;
 175         host->pio.len = 0;
 176
 177         host->status = HOST_S_IDLE;
 178
 179         bcsr->disk_leds |= (1 << 8);
 180
 181         mmc_request_done(host->mmc, mrq);
 182 }
 183
 184 static void au1xmmc_tasklet_finish(unsigned long param)
 185 {
 186         struct au1xmmc_host *host = (struct au1xmmc_host *) param;
 187         au1xmmc_finish_request(host);
 188 }
 189
 190 static int au1xmmc_send_command(struct au1xmmc_host *host, int wait,
 191                                 struct mmc_command *cmd)
 192 {
 193
 194         u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT);
 195
 196         switch (mmc_resp_type(cmd)) {
 197         case MMC_RSP_NONE:
 198                 break;
 199         case MMC_RSP_R1:
 200                 mmccmd |= SD_CMD_RT_1;
 201                 break;
 202         case MMC_RSP_R1B:
 203                 mmccmd |= SD_CMD_RT_1B;
 204                 break;
 205         case MMC_RSP_R2:
 206                 mmccmd |= SD_CMD_RT_2;
 207                 break;
 208         case MMC_RSP_R3:
 209                 mmccmd |= SD_CMD_RT_3;
 210                 break;
 211         default:
 212                 printk(KERN_INFO "au1xmmc: unhandled response type %02x\n",
 213                         mmc_resp_type(cmd));
 214                 return MMC_ERR_INVALID;
 215         }
 216
 217         switch(cmd->opcode) {
 218         case MMC_READ_SINGLE_BLOCK:
 219         case SD_APP_SEND_SCR:
 220                 mmccmd |= SD_CMD_CT_2;
 221                 break;
 222         case MMC_READ_MULTIPLE_BLOCK:
 223                 mmccmd |= SD_CMD_CT_4;
 224                 break;
 225         case MMC_WRITE_BLOCK:
 226                 mmccmd |= SD_CMD_CT_1;
 227                 break;
 228
 229         case MMC_WRITE_MULTIPLE_BLOCK:
 230                 mmccmd |= SD_CMD_CT_3;
 231                 break;
 232         case MMC_STOP_TRANSMISSION:
 233                 mmccmd |= SD_CMD_CT_7;
 234                 break;
 235         }
 236
 237         au_writel(cmd->arg, HOST_CMDARG(host));
 238         au_sync();
 239
 240         if (wait)
 241                 IRQ_OFF(host, SD_CONFIG_CR);
 242
 243         au_writel((mmccmd | SD_CMD_GO), HOST_CMD(host));
 244         au_sync();
 245
 246         /* Wait for the command to go on the line */
 247
 248         while(1) {
 249                 if (!(au_readl(HOST_CMD(host)) & SD_CMD_GO))
 250                         break;
 251         }
 252
 253         /* Wait for the command to come back */
 254
 255         if (wait) {
 256                 u32 status = au_readl(HOST_STATUS(host));
 257
 258                 while(!(status & SD_STATUS_CR))
 259                         status = au_readl(HOST_STATUS(host));
 260
 261                 /* Clear the CR status */
 262                 au_writel(SD_STATUS_CR, HOST_STATUS(host));
 263
 264                 IRQ_ON(host, SD_CONFIG_CR);
 265         }
 266
 267         return MMC_ERR_NONE;
 268 }
 269
 270 static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status)
 271 {
 272
 273         struct mmc_request *mrq = host->mrq;
 274         struct mmc_data *data;
 275         u32 crc;
 276
 277         WARN_ON(host->status != HOST_S_DATA && host->status != HOST_S_STOP);
 278
 279         if (host->mrq == NULL)
 280                 return;
 281
 282         data = mrq->cmd->data;
 283
 284         if (status == 0)
 285                 status = au_readl(HOST_STATUS(host));
 286
 287         /* The transaction is really over when the SD_STATUS_DB bit is clear */
 288
 289         while((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB))
 290                 status = au_readl(HOST_STATUS(host));
 291
 292         data->error = MMC_ERR_NONE;
 293         dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir);
 294
 295         /* Process any errors */
 296
 297         crc = (status & (SD_STATUS_WC | SD_STATUS_RC));
 298         if (host->flags & HOST_F_XMIT)
 299                 crc |= ((status & 0x07) == 0x02) ? 0 : 1;
 300
 301         if (crc)
 302                 data->error = MMC_ERR_BADCRC;
 303
 304         /* Clear the CRC bits */
 305         au_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host));
 306
 307         data->bytes_xfered = 0;
 308
 309         if (data->error == MMC_ERR_NONE) {
 310                 if (host->flags & HOST_F_DMA) {
 311                         u32 chan = DMA_CHANNEL(host);
 312
 313                         chan_tab_t *c = *((chan_tab_t **) chan);
 314                         au1x_dma_chan_t *cp = c->chan_ptr;
 315                         data->bytes_xfered = cp->ddma_bytecnt;
 316                 }
 317                 else
 318                         data->bytes_xfered =
 319                                 (data->blocks * data->blksz) -
 320                                 host->pio.len;
 321         }
 322
 323         au1xmmc_finish_request(host);
 324 }
 325
 326 static void au1xmmc_tasklet_data(unsigned long param)
 327 {
 328         struct au1xmmc_host *host = (struct au1xmmc_host *) param;
 329
 330         u32 status = au_readl(HOST_STATUS(host));
 331         au1xmmc_data_complete(host, status);
 332 }
 333
 334 #define AU1XMMC_MAX_TRANSFER 8
 335
 336 static void au1xmmc_send_pio(struct au1xmmc_host *host)
 337 {
 338
 339         struct mmc_data *data = 0;
 340         int sg_len, max, count = 0;
 341         unsigned char *sg_ptr;
 342         u32 status = 0;
 343         struct scatterlist *sg;
 344
 345         data = host->mrq->data;
 346
 347         if (!(host->flags & HOST_F_XMIT))
 348                 return;
 349
 350         /* This is the pointer to the data buffer */
 351         sg = &data->sg[host->pio.index];
 352         sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
 353
 354         /* This is the space left inside the buffer */
 355         sg_len = data->sg[host->pio.index].length - host->pio.offset;
 356
 357         /* Check to if we need less then the size of the sg_buffer */
 358
 359         max = (sg_len > host->pio.len) ? host->pio.len : sg_len;
 360         if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER;
 361
 362         for(count = 0; count < max; count++ ) {
 363                 unsigned char val;
 364
 365                 status = au_readl(HOST_STATUS(host));
 366
 367                 if (!(status & SD_STATUS_TH))
 368                         break;
 369
 370                 val = *sg_ptr++;
 371
 372                 au_writel((unsigned long) val, HOST_TXPORT(host));
 373                 au_sync();
 374         }
 375
 376         host->pio.len -= count;
 377         host->pio.offset += count;
 378
 379         if (count == sg_len) {
 380                 host->pio.index++;
 381                 host->pio.offset = 0;
 382         }
 383
 384         if (host->pio.len == 0) {
 385                 IRQ_OFF(host, SD_CONFIG_TH);
 386
 387                 if (host->flags & HOST_F_STOP)
 388                         SEND_STOP(host);
 389
 390                 tasklet_schedule(&host->data_task);
 391         }
 392 }
 393
 394 static void au1xmmc_receive_pio(struct au1xmmc_host *host)
 395 {
 396
 397         struct mmc_data *data = 0;
 398         int sg_len = 0, max = 0, count = 0;
 399         unsigned char *sg_ptr = 0;
 400         u32 status = 0;
 401         struct scatterlist *sg;
 402
 403         data = host->mrq->data;
 404
 405         if (!(host->flags & HOST_F_RECV))
 406                 return;
 407
 408         max = host->pio.len;
 409
 410         if (host->pio.index < host->dma.len) {
 411                 sg = &data->sg[host->pio.index];
 412                 sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
 413
 414                 /* This is the space left inside the buffer */
 415                 sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset;
 416
 417                 /* Check to if we need less then the size of the sg_buffer */
 418                 if (sg_len < max) max = sg_len;
 419         }
 420
 421         if (max > AU1XMMC_MAX_TRANSFER)
 422                 max = AU1XMMC_MAX_TRANSFER;
 423
 424         for(count = 0; count < max; count++ ) {
 425                 u32 val;
 426                 status = au_readl(HOST_STATUS(host));
 427
 428                 if (!(status & SD_STATUS_NE))
 429                         break;
 430
 431                 if (status & SD_STATUS_RC) {
 432                         DBG("RX CRC Error [%d + %d].\n", host->id,
 433                                         host->pio.len, count);
 434                         break;
 435                 }
 436
 437                 if (status & SD_STATUS_RO) {
 438                         DBG("RX Overrun [%d + %d]\n", host->id,
 439                                         host->pio.len, count);
 440                         break;
 441                 }
 442                 else if (status & SD_STATUS_RU) {
 443                         DBG("RX Underrun [%d + %d]\n", host->id,
 444                                         host->pio.len,  count);
 445                         break;
 446                 }
 447
 448                 val = au_readl(HOST_RXPORT(host));
 449
 450                 if (sg_ptr)
 451                         *sg_ptr++ = (unsigned char) (val & 0xFF);
 452         }
 453
 454         host->pio.len -= count;
 455         host->pio.offset += count;
 456
 457         if (sg_len && count == sg_len) {
 458                 host->pio.index++;
 459                 host->pio.offset = 0;
 460         }
 461
 462         if (host->pio.len == 0) {
 463                 //IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF);
 464                 IRQ_OFF(host, SD_CONFIG_NE);
 465
 466                 if (host->flags & HOST_F_STOP)
 467                         SEND_STOP(host);
 468
 469                 tasklet_schedule(&host->data_task);
 470         }
 471 }
 472
 473 /* static void au1xmmc_cmd_complete
 474    This is called when a command has been completed - grab the response
 475    and check for errors.  Then start the data transfer if it is indicated.
 476 */
 477
 478 static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status)
 479 {
 480
 481         struct mmc_request *mrq = host->mrq;
 482         struct mmc_command *cmd;
 483         int trans;
 484
 485         if (!host->mrq)
 486                 return;
 487
 488         cmd = mrq->cmd;
 489         cmd->error = MMC_ERR_NONE;
 490
 491         if (cmd->flags & MMC_RSP_PRESENT) {
 492                 if (cmd->flags & MMC_RSP_136) {
 493                         u32 r[4];
 494                         int i;
 495
 496                         r[0] = au_readl(host->iobase + SD_RESP3);
 497                         r[1] = au_readl(host->iobase + SD_RESP2);
 498                         r[2] = au_readl(host->iobase + SD_RESP1);
 499                         r[3] = au_readl(host->iobase + SD_RESP0);
 500
 501                         /* The CRC is omitted from the response, so really
 502                          * we only got 120 bytes, but the engine expects
 503                          * 128 bits, so we have to shift things up
 504                          */
 505
 506                         for(i = 0; i < 4; i++) {
 507                                 cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8;
 508                                 if (i != 3)
 509                                         cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24;
 510                         }
 511                 } else {
 512                         /* Techincally, we should be getting all 48 bits of
 513                          * the response (SD_RESP1 + SD_RESP2), but because
 514                          * our response omits the CRC, our data ends up
 515                          * being shifted 8 bits to the right.  In this case,
 516                          * that means that the OSR data starts at bit 31,
 517                          * so we can just read RESP0 and return that
 518                          */
 519                         cmd->resp[0] = au_readl(host->iobase + SD_RESP0);
 520                 }
 521         }
 522
 523         /* Figure out errors */
 524
 525         if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC))
 526                 cmd->error = MMC_ERR_BADCRC;
 527
 528         trans = host->flags & (HOST_F_XMIT | HOST_F_RECV);
 529
 530         if (!trans || cmd->error != MMC_ERR_NONE) {
 531
 532                 IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA|SD_CONFIG_RF);
 533                 tasklet_schedule(&host->finish_task);
 534                 return;
 535         }
 536
 537         host->status = HOST_S_DATA;
 538
 539         if (host->flags & HOST_F_DMA) {
 540                 u32 channel = DMA_CHANNEL(host);
 541
 542                 /* Start the DMA as soon as the buffer gets something in it */
 543
 544                 if (host->flags & HOST_F_RECV) {
 545                         u32 mask = SD_STATUS_DB | SD_STATUS_NE;
 546
 547                         while((status & mask) != mask)
 548                                 status = au_readl(HOST_STATUS(host));
 549                 }
 550
 551                 au1xxx_dbdma_start(channel);
 552         }
 553 }
 554
 555 static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate)
 556 {
 557
 558         unsigned int pbus = get_au1x00_speed();
 559         unsigned int divisor;
 560         u32 config;
 561
 562         /* From databook:
 563            divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1
 564         */
 565
 566         pbus /= ((au_readl(SYS_POWERCTRL) & 0x3) + 2);
 567         pbus /= 2;
 568
 569         divisor = ((pbus / rate) / 2) - 1;
 570
 571         config = au_readl(HOST_CONFIG(host));
 572
 573         config &= ~(SD_CONFIG_DIV);
 574         config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE;
 575
 576         au_writel(config, HOST_CONFIG(host));
 577         au_sync();
 578 }
 579
 580 static int
 581 au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data)
 582 {
 583
 584         int datalen = data->blocks * data->blksz;
 585
 586         if (dma != 0)
 587                 host->flags |= HOST_F_DMA;
 588
 589         if (data->flags & MMC_DATA_READ)
 590                 host->flags |= HOST_F_RECV;
 591         else
 592                 host->flags |= HOST_F_XMIT;
 593
 594         if (host->mrq->stop)
 595                 host->flags |= HOST_F_STOP;
 596
 597         host->dma.dir = DMA_BIDIRECTIONAL;
 598
 599         host->dma.len = dma_map_sg(mmc_dev(host->mmc), data->sg,
 600                                    data->sg_len, host->dma.dir);
 601
 602         if (host->dma.len == 0)
 603                 return MMC_ERR_TIMEOUT;
 604
 605         au_writel(data->blksz - 1, HOST_BLKSIZE(host));
 606
 607         if (host->flags & HOST_F_DMA) {
 608                 int i;
 609                 u32 channel = DMA_CHANNEL(host);
 610
 611                 au1xxx_dbdma_stop(channel);
 612
 613                 for(i = 0; i < host->dma.len; i++) {
 614                         u32 ret = 0, flags = DDMA_FLAGS_NOIE;
 615                         struct scatterlist *sg = &data->sg[i];
 616                         int sg_len = sg->length;
 617
 618                         int len = (datalen > sg_len) ? sg_len : datalen;
 619
 620                         if (i == host->dma.len - 1)
 621                                 flags = DDMA_FLAGS_IE;
 622
 623                         if (host->flags & HOST_F_XMIT){
 624                                 ret = au1xxx_dbdma_put_source_flags(channel,
 625                                         (void *) (page_address(sg->page) +
 626                                                   sg->offset),
 627                                         len, flags);
 628                         }
 629                         else {
 630                                 ret = au1xxx_dbdma_put_dest_flags(channel,
 631                                         (void *) (page_address(sg->page) +
 632                                                   sg->offset),
 633                                         len, flags);
 634                         }
 635
 636                         if (!ret)
 637                                 goto dataerr;
 638
 639                         datalen -= len;
 640                 }
 641         }
 642         else {
 643                 host->pio.index = 0;
 644                 host->pio.offset = 0;
 645                 host->pio.len = datalen;
 646
 647                 if (host->flags & HOST_F_XMIT)
 648                         IRQ_ON(host, SD_CONFIG_TH);
 649                 else
 650                         IRQ_ON(host, SD_CONFIG_NE);
 651                         //IRQ_ON(host, SD_CONFIG_RA|SD_CONFIG_RF);
 652         }
 653
 654         return MMC_ERR_NONE;
 655
 656  dataerr:
 657         dma_unmap_sg(mmc_dev(host->mmc),data->sg,data->sg_len,host->dma.dir);
 658         return MMC_ERR_TIMEOUT;
 659 }
 660
 661 /* static void au1xmmc_request
 662    This actually starts a command or data transaction
 663 */
 664
 665 static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq)
 666 {
 667
 668         struct au1xmmc_host *host = mmc_priv(mmc);
 669         int ret = MMC_ERR_NONE;
 670
 671         WARN_ON(irqs_disabled());
 672         WARN_ON(host->status != HOST_S_IDLE);
 673
 674         host->mrq = mrq;
 675         host->status = HOST_S_CMD;
 676
 677         bcsr->disk_leds &= ~(1 << 8);
 678
 679         if (mrq->data) {
 680                 FLUSH_FIFO(host);
 681                 ret = au1xmmc_prepare_data(host, mrq->data);
 682         }
 683
 684         if (ret == MMC_ERR_NONE)
 685                 ret = au1xmmc_send_command(host, 0, mrq->cmd);
 686
 687         if (ret != MMC_ERR_NONE) {
 688                 mrq->cmd->error = ret;
 689                 au1xmmc_finish_request(host);
 690         }
 691 }
 692
 693 static void au1xmmc_reset_controller(struct au1xmmc_host *host)
 694 {
 695
 696         /* Apply the clock */
 697         au_writel(SD_ENABLE_CE, HOST_ENABLE(host));
 698         au_sync_delay(1);
 699
 700         au_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host));
 701         au_sync_delay(5);
 702
 703         au_writel(~0, HOST_STATUS(host));
 704         au_sync();
 705
 706         au_writel(0, HOST_BLKSIZE(host));
 707         au_writel(0x001fffff, HOST_TIMEOUT(host));
 708         au_sync();
 709
 710         au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
 711         au_sync();
 712
 713         au_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host));
 714         au_sync_delay(1);
 715
 716         au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
 717         au_sync();
 718
 719         /* Configure interrupts */
 720         au_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host));
 721         au_sync();
 722 }
 723
 724
 725 static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios)
 726 {
 727         struct au1xmmc_host *host = mmc_priv(mmc);
 728
 729         if (ios->power_mode == MMC_POWER_OFF)
 730                 au1xmmc_set_power(host, 0);
 731         else if (ios->power_mode == MMC_POWER_ON) {
 732                 au1xmmc_set_power(host, 1);
 733         }
 734
 735         if (ios->clock && ios->clock != host->clock) {
 736                 au1xmmc_set_clock(host, ios->clock);
 737                 host->clock = ios->clock;
 738         }
 739 }
 740
 741 static void au1xmmc_dma_callback(int irq, void *dev_id)
 742 {
 743         struct au1xmmc_host *host = (struct au1xmmc_host *) dev_id;
 744
 745         /* Avoid spurious interrupts */
 746
 747         if (!host->mrq)
 748                 return;
 749
 750         if (host->flags & HOST_F_STOP)
 751                 SEND_STOP(host);
 752
 753         tasklet_schedule(&host->data_task);
 754 }
 755
 756 #define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT)
 757 #define STATUS_DATA_IN  (SD_STATUS_NE)
 758 #define STATUS_DATA_OUT (SD_STATUS_TH)
 759
 760 static irqreturn_t au1xmmc_irq(int irq, void *dev_id)
 761 {
 762
 763         u32 status;
 764         int i, ret = 0;
 765
 766         disable_irq(AU1100_SD_IRQ);
 767
 768         for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
 769                 struct au1xmmc_host * host = au1xmmc_hosts[i];
 770                 u32 handled = 1;
 771
 772                 status = au_readl(HOST_STATUS(host));
 773
 774                 if (host->mrq && (status & STATUS_TIMEOUT)) {
 775                         if (status & SD_STATUS_RAT)
 776                                 host->mrq->cmd->error = MMC_ERR_TIMEOUT;
 777
 778                         else if (status & SD_STATUS_DT)
 779                                 host->mrq->data->error = MMC_ERR_TIMEOUT;
 780
 781                         /* In PIO mode, interrupts might still be enabled */
 782                         IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH);
 783
 784                         //IRQ_OFF(host, SD_CONFIG_TH|SD_CONFIG_RA|SD_CONFIG_RF);
 785                         tasklet_schedule(&host->finish_task);
 786                 }
 787 #if 0
 788                 else if (status & SD_STATUS_DD) {
 789
 790                         /* Sometimes we get a DD before a NE in PIO mode */
 791
 792                         if (!(host->flags & HOST_F_DMA) &&
 793                                         (status & SD_STATUS_NE))
 794                                 au1xmmc_receive_pio(host);
 795                         else {
 796                                 au1xmmc_data_complete(host, status);
 797                                 //tasklet_schedule(&host->data_task);
 798                         }
 799                 }
 800 #endif
 801                 else if (status & (SD_STATUS_CR)) {
 802                         if (host->status == HOST_S_CMD)
 803                                 au1xmmc_cmd_complete(host,status);
 804                 }
 805                 else if (!(host->flags & HOST_F_DMA)) {
 806                         if ((host->flags & HOST_F_XMIT) &&
 807                             (status & STATUS_DATA_OUT))
 808                                 au1xmmc_send_pio(host);
 809                         else if ((host->flags & HOST_F_RECV) &&
 810                             (status & STATUS_DATA_IN))
 811                                 au1xmmc_receive_pio(host);
 812                 }
 813                 else if (status & 0x203FBC70) {
 814                         DBG("Unhandled status %8.8x\n", host->id, status);
 815                         handled = 0;
 816                 }
 817
 818                 au_writel(status, HOST_STATUS(host));
 819                 au_sync();
 820
 821                 ret |= handled;
 822         }
 823
 824         enable_irq(AU1100_SD_IRQ);
 825         return ret;
 826 }
 827
 828 static void au1xmmc_poll_event(unsigned long arg)
 829 {
 830         struct au1xmmc_host *host = (struct au1xmmc_host *) arg;
 831
 832         int card = au1xmmc_card_inserted(host);
 833         int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0;
 834
 835         if (card != controller) {
 836                 host->flags &= ~HOST_F_ACTIVE;
 837                 if (card) host->flags |= HOST_F_ACTIVE;
 838                 mmc_detect_change(host->mmc, 0);
 839         }
 840
 841         if (host->mrq != NULL) {
 842                 u32 status = au_readl(HOST_STATUS(host));
 843                 DBG("PENDING - %8.8x\n", host->id, status);
 844         }
 845
 846         mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT);
 847 }
 848
 849 static dbdev_tab_t au1xmmc_mem_dbdev =
 850 {
 851         DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 8, 0x00000000, 0, 0
 852 };
 853
 854 static void au1xmmc_init_dma(struct au1xmmc_host *host)
 855 {
 856
 857         u32 rxchan, txchan;
 858
 859         int txid = au1xmmc_card_table[host->id].tx_devid;
 860         int rxid = au1xmmc_card_table[host->id].rx_devid;
 861
 862         /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride
 863            of 8 bits.  And since devices are shared, we need to create
 864            our own to avoid freaking out other devices
 865         */
 866
 867         int memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev);
 868
 869         txchan = au1xxx_dbdma_chan_alloc(memid, txid,
 870                                          au1xmmc_dma_callback, (void *) host);
 871
 872         rxchan = au1xxx_dbdma_chan_alloc(rxid, memid,
 873                                          au1xmmc_dma_callback, (void *) host);
 874
 875         au1xxx_dbdma_set_devwidth(txchan, 8);
 876         au1xxx_dbdma_set_devwidth(rxchan, 8);
 877
 878         au1xxx_dbdma_ring_alloc(txchan, AU1XMMC_DESCRIPTOR_COUNT);
 879         au1xxx_dbdma_ring_alloc(rxchan, AU1XMMC_DESCRIPTOR_COUNT);
 880
 881         host->tx_chan = txchan;
 882         host->rx_chan = rxchan;
 883 }
 884
 885 static const struct mmc_host_ops au1xmmc_ops = {
 886         .request        = au1xmmc_request,
 887         .set_ios        = au1xmmc_set_ios,
 888         .get_ro         = au1xmmc_card_readonly,
 889 };
 890
 891 static int __devinit au1xmmc_probe(struct platform_device *pdev)
 892 {
 893
 894         int i, ret = 0;
 895
 896         /* THe interrupt is shared among all controllers */
 897         ret = request_irq(AU1100_SD_IRQ, au1xmmc_irq, IRQF_DISABLED, "MMC", 0);
 898
 899         if (ret) {
 900                 printk(DRIVER_NAME "ERROR: Couldn't get int %d: %d\n",
 901                                 AU1100_SD_IRQ, ret);
 902                 return -ENXIO;
 903         }
 904
 905         disable_irq(AU1100_SD_IRQ);
 906
 907         for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
 908                 struct mmc_host *mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev);
 909                 struct au1xmmc_host *host = 0;
 910
 911                 if (!mmc) {
 912                         printk(DRIVER_NAME "ERROR: no mem for host %d\n", i);
 913                         au1xmmc_hosts[i] = 0;
 914                         continue;
 915                 }
 916
 917                 mmc->ops = &au1xmmc_ops;
 918
 919                 mmc->f_min =   450000;
 920                 mmc->f_max = 24000000;
 921
 922                 mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE;
 923                 mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT;
 924
 925                 mmc->max_blk_size = 2048;
 926                 mmc->max_blk_count = 512;
 927
 928                 mmc->ocr_avail = AU1XMMC_OCR;
 929
 930                 host = mmc_priv(mmc);
 931                 host->mmc = mmc;
 932
 933                 host->id = i;
 934                 host->iobase = au1xmmc_card_table[host->id].iobase;
 935                 host->clock = 0;
 936                 host->power_mode = MMC_POWER_OFF;
 937
 938                 host->flags = au1xmmc_card_inserted(host) ? HOST_F_ACTIVE : 0;
 939                 host->status = HOST_S_IDLE;
 940
 941                 init_timer(&host->timer);
 942
 943                 host->timer.function = au1xmmc_poll_event;
 944                 host->timer.data = (unsigned long) host;
 945                 host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT;
 946
 947                 tasklet_init(&host->data_task, au1xmmc_tasklet_data,
 948                                 (unsigned long) host);
 949
 950                 tasklet_init(&host->finish_task, au1xmmc_tasklet_finish,
 951                                 (unsigned long) host);
 952
 953                 spin_lock_init(&host->lock);
 954
 955                 if (dma != 0)
 956                         au1xmmc_init_dma(host);
 957
 958                 au1xmmc_reset_controller(host);
 959
 960                 mmc_add_host(mmc);
 961                 au1xmmc_hosts[i] = host;
 962
 963                 add_timer(&host->timer);
 964
 965                 printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X (mode=%s)\n",
 966                        host->id, host->iobase, dma ? "dma" : "pio");
 967         }
 968
 969         enable_irq(AU1100_SD_IRQ);
 970
 971         return 0;
 972 }
 973
 974 static int __devexit au1xmmc_remove(struct platform_device *pdev)
 975 {
 976
 977         int i;
 978
 979         disable_irq(AU1100_SD_IRQ);
 980
 981         for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
 982                 struct au1xmmc_host *host = au1xmmc_hosts[i];
 983                 if (!host) continue;
 984
 985                 tasklet_kill(&host->data_task);
 986                 tasklet_kill(&host->finish_task);
 987
 988                 del_timer_sync(&host->timer);
 989                 au1xmmc_set_power(host, 0);
 990
 991                 mmc_remove_host(host->mmc);
 992
 993                 au1xxx_dbdma_chan_free(host->tx_chan);
 994                 au1xxx_dbdma_chan_free(host->rx_chan);
 995
 996                 au_writel(0x0, HOST_ENABLE(host));
 997                 au_sync();
 998         }
 999
1000         free_irq(AU1100_SD_IRQ, 0);
1001         return 0;
1002 }
1003
1004 static struct platform_driver au1xmmc_driver = {
1005         .probe         = au1xmmc_probe,
1006         .remove        = au1xmmc_remove,
1007         .suspend       = NULL,
1008         .resume        = NULL,
1009         .driver        = {
1010                 .name  = DRIVER_NAME,
1011         },
1012 };
1013
1014 static int __init au1xmmc_init(void)
1015 {
1016         return platform_driver_register(&au1xmmc_driver);
1017 }
1018
1019 static void __exit au1xmmc_exit(void)
1020 {
1021         platform_driver_unregister(&au1xmmc_driver);
1022 }
1023
1024 module_init(au1xmmc_init);
1025 module_exit(au1xmmc_exit);
1026
1027 #ifdef MODULE
1028 MODULE_AUTHOR("Advanced Micro Devices, Inc");
1029 MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX");
1030 MODULE_LICENSE("GPL");
1031 #endif
1032