#include <linux/timer.h>
#include <linux/acpi_pmtmr.h>
#include <linux/cpufreq.h>
-#include <linux/dmi.h>
#include <linux/delay.h>
#include <linux/clocksource.h>
#include <linux/percpu.h>
* unstable. We do this because unlike Time Of Day,
* the scheduler clock tolerates small errors and it's
* very important for it to be as fast as the platform
- * can achive it. )
+ * can achieve it. )
*/
if (unlikely(tsc_disabled)) {
/* No locking but a rare wrong value is not a big deal: */
__setup("notsc", notsc_setup);
+static int no_sched_irq_time;
+
static int __init tsc_setup(char *str)
{
if (!strcmp(str, "reliable"))
tsc_clocksource_reliable = 1;
+ if (!strncmp(str, "noirqtime", 9))
+ no_sched_irq_time = 1;
return 1;
}
static inline int pit_expect_msb(unsigned char val, u64 *tscp, unsigned long *deltap)
{
int count;
- u64 tsc = 0;
+ u64 tsc = 0, prev_tsc = 0;
for (count = 0; count < 50000; count++) {
if (!pit_verify_msb(val))
break;
+ prev_tsc = tsc;
tsc = get_cycles();
}
- *deltap = get_cycles() - tsc;
+ *deltap = get_cycles() - prev_tsc;
*tscp = tsc;
/*
* How many MSB values do we want to see? We aim for
* a maximum error rate of 500ppm (in practice the
* real error is much smaller), but refuse to spend
- * more than 25ms on it.
+ * more than 50ms on it.
*/
-#define MAX_QUICK_PIT_MS 25
+#define MAX_QUICK_PIT_MS 50
#define MAX_QUICK_PIT_ITERATIONS (MAX_QUICK_PIT_MS * PIT_TICK_RATE / 1000 / 256)
static unsigned long quick_pit_calibrate(void)
*
* As a result, we can depend on there not being
* any odd delays anywhere, and the TSC reads are
- * reliable (within the error). We also adjust the
- * delta to the middle of the error bars, just
- * because it looks nicer.
+ * reliable (within the error).
*
* kHz = ticks / time-in-seconds / 1000;
* kHz = (t2 - t1) / (I * 256 / PIT_TICK_RATE) / 1000
* kHz = ((t2 - t1) * PIT_TICK_RATE) / (I * 256 * 1000)
*/
- delta += (long)(d2 - d1)/2;
delta *= PIT_TICK_RATE;
do_div(delta, i*256*1000);
printk("Fast TSC calibration using PIT\n");
* the delta to the previous read. We keep track of the min
* and max values of that delta. The delta is mostly defined
* by the IO time of the PIT access, so we can detect when a
- * SMI/SMM disturbance happend between the two reads. If the
+ * SMI/SMM disturbance happened between the two reads. If the
* maximum time is significantly larger than the minimum time,
* then we discard the result and have another try.
*
tsc_pit_min = min(tsc_pit_min, tsc_pit_khz);
/* hpet or pmtimer available ? */
- if (!hpet && !ref1 && !ref2)
+ if (ref1 == ref2)
continue;
/* Check, whether the sampling was disturbed by an SMI */
if (cpu_khz) {
*scale = (NSEC_PER_MSEC << CYC2NS_SCALE_FACTOR)/cpu_khz;
- *offset = ns_now - (tsc_now * *scale >> CYC2NS_SCALE_FACTOR);
+ *offset = ns_now - mult_frac(tsc_now, *scale,
+ (1UL << CYC2NS_SCALE_FACTOR));
}
sched_clock_idle_wakeup_event(0);
local_irq_restore(flags);
}
+static unsigned long long cyc2ns_suspend;
+
+void save_sched_clock_state(void)
+{
+ if (!sched_clock_stable)
+ return;
+
+ cyc2ns_suspend = sched_clock();
+}
+
+/*
+ * Even on processors with invariant TSC, TSC gets reset in some the
+ * ACPI system sleep states. And in some systems BIOS seem to reinit TSC to
+ * arbitrary value (still sync'd across cpu's) during resume from such sleep
+ * states. To cope up with this, recompute the cyc2ns_offset for each cpu so
+ * that sched_clock() continues from the point where it was left off during
+ * suspend.
+ */
+void restore_sched_clock_state(void)
+{
+ unsigned long long offset;
+ unsigned long flags;
+ int cpu;
+
+ if (!sched_clock_stable)
+ return;
+
+ local_irq_save(flags);
+
+ __this_cpu_write(cyc2ns_offset, 0);
+ offset = cyc2ns_suspend - sched_clock();
+
+ for_each_possible_cpu(cpu)
+ per_cpu(cyc2ns_offset, cpu) = offset;
+
+ local_irq_restore(flags);
+}
+
#ifdef CONFIG_CPU_FREQ
/* Frequency scaling support. Adjust the TSC based timer when the cpu frequency
ret : clocksource_tsc.cycle_last;
}
-#ifdef CONFIG_X86_64
-static cycle_t __vsyscall_fn vread_tsc(void)
-{
- cycle_t ret;
-
- /*
- * Surround the RDTSC by barriers, to make sure it's not
- * speculated to outside the seqlock critical section and
- * does not cause time warps:
- */
- rdtsc_barrier();
- ret = (cycle_t)vget_cycles();
- rdtsc_barrier();
-
- return ret >= __vsyscall_gtod_data.clock.cycle_last ?
- ret : __vsyscall_gtod_data.clock.cycle_last;
-}
-#endif
-
static void resume_tsc(struct clocksource *cs)
{
clocksource_tsc.cycle_last = 0;
.read = read_tsc,
.resume = resume_tsc,
.mask = CLOCKSOURCE_MASK(64),
- .shift = 22,
.flags = CLOCK_SOURCE_IS_CONTINUOUS |
CLOCK_SOURCE_MUST_VERIFY,
#ifdef CONFIG_X86_64
- .vread = vread_tsc,
+ .archdata = { .vclock_mode = VCLOCK_TSC },
#endif
};
if (!tsc_unstable) {
tsc_unstable = 1;
sched_clock_stable = 0;
+ disable_sched_clock_irqtime();
printk(KERN_INFO "Marking TSC unstable due to %s\n", reason);
/* Change only the rating, when not registered */
if (clocksource_tsc.mult)
EXPORT_SYMBOL_GPL(mark_tsc_unstable);
-static int __init dmi_mark_tsc_unstable(const struct dmi_system_id *d)
-{
- printk(KERN_NOTICE "%s detected: marking TSC unstable.\n",
- d->ident);
- tsc_unstable = 1;
- return 0;
-}
-
-/* List of systems that have known TSC problems */
-static struct dmi_system_id __initdata bad_tsc_dmi_table[] = {
- {
- .callback = dmi_mark_tsc_unstable,
- .ident = "IBM Thinkpad 380XD",
- .matches = {
- DMI_MATCH(DMI_BOARD_VENDOR, "IBM"),
- DMI_MATCH(DMI_BOARD_NAME, "2635FA0"),
- },
- },
- {}
-};
-
static void __init check_system_tsc_reliable(void)
{
#ifdef CONFIG_MGEODE_LX
unsigned long res_low, res_high;
rdmsr_safe(MSR_GEODE_BUSCONT_CONF0, &res_low, &res_high);
- /* Geode_LX - the OLPC CPU has a possibly a very reliable TSC */
+ /* Geode_LX - the OLPC CPU has a very reliable TSC */
if (res_low & RTSC_SUSP)
tsc_clocksource_reliable = 1;
#endif
if (boot_cpu_has(X86_FEATURE_CONSTANT_TSC))
return 0;
+
+ if (tsc_clocksource_reliable)
+ return 0;
/*
* Intel systems are normally all synchronized.
* Exceptions must mark TSC as unstable:
if (boot_cpu_data.x86_vendor != X86_VENDOR_INTEL) {
/* assume multi socket systems are not synchronized: */
if (num_possible_cpus() > 1)
- tsc_unstable = 1;
+ return 1;
}
- return tsc_unstable;
+ return 0;
}
-static void __init init_tsc_clocksource(void)
+
+static void tsc_refine_calibration_work(struct work_struct *work);
+static DECLARE_DELAYED_WORK(tsc_irqwork, tsc_refine_calibration_work);
+/**
+ * tsc_refine_calibration_work - Further refine tsc freq calibration
+ * @work - ignored.
+ *
+ * This functions uses delayed work over a period of a
+ * second to further refine the TSC freq value. Since this is
+ * timer based, instead of loop based, we don't block the boot
+ * process while this longer calibration is done.
+ *
+ * If there are any calibration anomalies (too many SMIs, etc),
+ * or the refined calibration is off by 1% of the fast early
+ * calibration, we throw out the new calibration and use the
+ * early calibration.
+ */
+static void tsc_refine_calibration_work(struct work_struct *work)
{
- clocksource_tsc.mult = clocksource_khz2mult(tsc_khz,
- clocksource_tsc.shift);
+ static u64 tsc_start = -1, ref_start;
+ static int hpet;
+ u64 tsc_stop, ref_stop, delta;
+ unsigned long freq;
+
+ /* Don't bother refining TSC on unstable systems */
+ if (check_tsc_unstable())
+ goto out;
+
+ /*
+ * Since the work is started early in boot, we may be
+ * delayed the first time we expire. So set the workqueue
+ * again once we know timers are working.
+ */
+ if (tsc_start == -1) {
+ /*
+ * Only set hpet once, to avoid mixing hardware
+ * if the hpet becomes enabled later.
+ */
+ hpet = is_hpet_enabled();
+ schedule_delayed_work(&tsc_irqwork, HZ);
+ tsc_start = tsc_read_refs(&ref_start, hpet);
+ return;
+ }
+
+ tsc_stop = tsc_read_refs(&ref_stop, hpet);
+
+ /* hpet or pmtimer available ? */
+ if (ref_start == ref_stop)
+ goto out;
+
+ /* Check, whether the sampling was disturbed by an SMI */
+ if (tsc_start == ULLONG_MAX || tsc_stop == ULLONG_MAX)
+ goto out;
+
+ delta = tsc_stop - tsc_start;
+ delta *= 1000000LL;
+ if (hpet)
+ freq = calc_hpet_ref(delta, ref_start, ref_stop);
+ else
+ freq = calc_pmtimer_ref(delta, ref_start, ref_stop);
+
+ /* Make sure we're within 1% */
+ if (abs(tsc_khz - freq) > tsc_khz/100)
+ goto out;
+
+ tsc_khz = freq;
+ printk(KERN_INFO "Refined TSC clocksource calibration: "
+ "%lu.%03lu MHz.\n", (unsigned long)tsc_khz / 1000,
+ (unsigned long)tsc_khz % 1000);
+
+out:
+ clocksource_register_khz(&clocksource_tsc, tsc_khz);
+}
+
+
+static int __init init_tsc_clocksource(void)
+{
+ if (!cpu_has_tsc || tsc_disabled > 0 || !tsc_khz)
+ return 0;
+
if (tsc_clocksource_reliable)
clocksource_tsc.flags &= ~CLOCK_SOURCE_MUST_VERIFY;
/* lower the rating if we already know its unstable: */
clocksource_tsc.rating = 0;
clocksource_tsc.flags &= ~CLOCK_SOURCE_IS_CONTINUOUS;
}
- clocksource_register(&clocksource_tsc);
-}
-
-#ifdef CONFIG_X86_64
-/*
- * calibrate_cpu is used on systems with fixed rate TSCs to determine
- * processor frequency
- */
-#define TICK_COUNT 100000000
-static unsigned long __init calibrate_cpu(void)
-{
- int tsc_start, tsc_now;
- int i, no_ctr_free;
- unsigned long evntsel3 = 0, pmc3 = 0, pmc_now = 0;
- unsigned long flags;
-
- for (i = 0; i < 4; i++)
- if (avail_to_resrv_perfctr_nmi_bit(i))
- break;
- no_ctr_free = (i == 4);
- if (no_ctr_free) {
- WARN(1, KERN_WARNING "Warning: AMD perfctrs busy ... "
- "cpu_khz value may be incorrect.\n");
- i = 3;
- rdmsrl(MSR_K7_EVNTSEL3, evntsel3);
- wrmsrl(MSR_K7_EVNTSEL3, 0);
- rdmsrl(MSR_K7_PERFCTR3, pmc3);
- } else {
- reserve_perfctr_nmi(MSR_K7_PERFCTR0 + i);
- reserve_evntsel_nmi(MSR_K7_EVNTSEL0 + i);
- }
- local_irq_save(flags);
- /* start measuring cycles, incrementing from 0 */
- wrmsrl(MSR_K7_PERFCTR0 + i, 0);
- wrmsrl(MSR_K7_EVNTSEL0 + i, 1 << 22 | 3 << 16 | 0x76);
- rdtscl(tsc_start);
- do {
- rdmsrl(MSR_K7_PERFCTR0 + i, pmc_now);
- tsc_now = get_cycles();
- } while ((tsc_now - tsc_start) < TICK_COUNT);
- local_irq_restore(flags);
- if (no_ctr_free) {
- wrmsrl(MSR_K7_EVNTSEL3, 0);
- wrmsrl(MSR_K7_PERFCTR3, pmc3);
- wrmsrl(MSR_K7_EVNTSEL3, evntsel3);
- } else {
- release_perfctr_nmi(MSR_K7_PERFCTR0 + i);
- release_evntsel_nmi(MSR_K7_EVNTSEL0 + i);
+ /*
+ * Trust the results of the earlier calibration on systems
+ * exporting a reliable TSC.
+ */
+ if (boot_cpu_has(X86_FEATURE_TSC_RELIABLE)) {
+ clocksource_register_khz(&clocksource_tsc, tsc_khz);
+ return 0;
}
- return pmc_now * tsc_khz / (tsc_now - tsc_start);
+ schedule_delayed_work(&tsc_irqwork, 0);
+ return 0;
}
-#else
-static inline unsigned long calibrate_cpu(void) { return cpu_khz; }
-#endif
+/*
+ * We use device_initcall here, to ensure we run after the hpet
+ * is fully initialized, which may occur at fs_initcall time.
+ */
+device_initcall(init_tsc_clocksource);
void __init tsc_init(void)
{
return;
}
- if (cpu_has(&boot_cpu_data, X86_FEATURE_CONSTANT_TSC) &&
- (boot_cpu_data.x86_vendor == X86_VENDOR_AMD))
- cpu_khz = calibrate_cpu();
-
printk("Detected %lu.%03lu MHz processor.\n",
(unsigned long)cpu_khz / 1000,
(unsigned long)cpu_khz % 1000);
/* now allow native_sched_clock() to use rdtsc */
tsc_disabled = 0;
+ if (!no_sched_irq_time)
+ enable_sched_clock_irqtime();
+
lpj = ((u64)tsc_khz * 1000);
do_div(lpj, HZ);
lpj_fine = lpj;
use_tsc_delay();
- /* Check and install the TSC clocksource */
- dmi_check_system(bad_tsc_dmi_table);
if (unsynchronized_tsc())
mark_tsc_unstable("TSCs unsynchronized");
check_system_tsc_reliable();
- init_tsc_clocksource();
}