if INPUT_TOUCHSCREEN
+config TOUCHSCREEN_88PM860X
+ tristate "Marvell 88PM860x touchscreen"
+ depends on MFD_88PM860X
+ help
+ Say Y here if you have a 88PM860x PMIC and want to enable
+ support for the built-in touchscreen.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called 88pm860x-ts.
+
config TOUCHSCREEN_ADS7846
- tristate "ADS 7846/7843 based touchscreens"
+ tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
depends on SPI_MASTER
depends on HWMON = n || HWMON
help
Say Y here if you have a touchscreen interface using the
- ADS7846 or ADS7843 controller, and your board-specific setup
- code includes that in its table of SPI devices.
+ ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
+ and your board-specific setup code includes that in its
+ table of SPI devices.
If HWMON is selected, and the driver is told the reference voltage
on your board, you will also get hwmon interfaces for the voltage
- (and on ads7846, temperature) sensors of this chip.
+ (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
If unsure, say N (but it's safe to say "Y").
To compile this driver as a module, choose M here: the
module will be called ads7846.
+config TOUCHSCREEN_AD7877
+ tristate "AD7877 based touchscreens"
+ depends on SPI_MASTER
+ help
+ Say Y here if you have a touchscreen interface using the
+ AD7877 controller, and your board-specific initialization
+ code includes that in its table of SPI devices.
+
+ If unsure, say N (but it's safe to say "Y").
+
+ To compile this driver as a module, choose M here: the
+ module will be called ad7877.
+
+config TOUCHSCREEN_AD7879
+ tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
+ help
+ Say Y here if you want to support a touchscreen interface using
+ the AD7879-1/AD7889-1 controller.
+
+ You should select a bus connection too.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ad7879.
+
+config TOUCHSCREEN_AD7879_I2C
+ tristate "support I2C bus connection"
+ depends on TOUCHSCREEN_AD7879 && I2C
+ help
+ Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ad7879-i2c.
+
+config TOUCHSCREEN_AD7879_SPI
+ tristate "support SPI bus connection"
+ depends on TOUCHSCREEN_AD7879 && SPI_MASTER
+ help
+ Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
+
+ If unsure, say N (but it's safe to say "Y").
+
+ To compile this driver as a module, choose M here: the
+ module will be called ad7879-spi.
+
config TOUCHSCREEN_BITSY
tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
depends on SA1100_BITSY
To compile this driver as a module, choose M here: the
module will be called h3600_ts_input.
-config TOUCHSCREEN_CORGI
- tristate "SharpSL (Corgi and Spitz series) touchscreen driver"
- depends on PXA_SHARPSL
+config TOUCHSCREEN_BU21013
+ tristate "BU21013 based touch panel controllers"
+ depends on I2C
+ help
+ Say Y here if you have a bu21013 touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called bu21013_ts.
+
+config TOUCHSCREEN_CY8CTMG110
+ tristate "cy8ctmg110 touchscreen"
+ depends on I2C
+ depends on GPIOLIB
+
+ help
+ Say Y here if you have a cy8ctmg110 capacitive touchscreen on
+ an AAVA device.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called cy8ctmg110_ts.
+
+config TOUCHSCREEN_DA9034
+ tristate "Touchscreen support for Dialog Semiconductor DA9034"
+ depends on PMIC_DA903X
default y
help
- Say Y here to enable the driver for the touchscreen on the
- Sharp SL-C7xx and SL-Cxx00 series of PDAs.
+ Say Y here to enable the support for the touchscreen found
+ on Dialog Semiconductor DA9034 PMIC.
+
+config TOUCHSCREEN_DYNAPRO
+ tristate "Dynapro serial touchscreen"
+ select SERIO
+ help
+ Say Y here if you have a Dynapro serial touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called dynapro.
+
+config TOUCHSCREEN_HAMPSHIRE
+ tristate "Hampshire serial touchscreen"
+ select SERIO
+ help
+ Say Y here if you have a Hampshire serial touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called hampshire.
+
+config TOUCHSCREEN_EETI
+ tristate "EETI touchscreen panel support"
+ depends on I2C
+ help
+ Say Y here to enable support for I2C connected EETI touch panels.
+
+ To compile this driver as a module, choose M here: the
+ module will be called eeti_ts.
+
+config TOUCHSCREEN_FUJITSU
+ tristate "Fujitsu serial touchscreen"
+ select SERIO
+ help
+ Say Y here if you have the Fujitsu touchscreen (such as one
+ installed in Lifebook P series laptop) connected to your
+ system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called fujitsu-ts.
+
+config TOUCHSCREEN_S3C2410
+ tristate "Samsung S3C2410/generic touchscreen input driver"
+ depends on ARCH_S3C2410 || SAMSUNG_DEV_TS
+ select S3C_ADC
+ help
+ Say Y here if you have the s3c2410 touchscreen.
If unsure, say N.
To compile this driver as a module, choose M here: the
- module will be called corgi_ts.
+ module will be called s3c2410_ts.
config TOUCHSCREEN_GUNZE
tristate "Gunze AHL-51S touchscreen"
To compile this driver as a module, choose M here: the
module will be called elo.
+config TOUCHSCREEN_WACOM_W8001
+ tristate "Wacom W8001 penabled serial touchscreen"
+ select SERIO
+ help
+ Say Y here if you have an Wacom W8001 penabled serial touchscreen
+ connected to your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called wacom_w8001.
+
+config TOUCHSCREEN_LPC32XX
+ tristate "LPC32XX touchscreen controller"
+ depends on ARCH_LPC32XX
+ help
+ Say Y here if you have a LPC32XX device and want
+ to support the built-in touchscreen.
+
+ To compile this driver as a module, choose M here: the
+ module will be called lpc32xx_ts.
+
+config TOUCHSCREEN_MCS5000
+ tristate "MELFAS MCS-5000 touchscreen"
+ depends on I2C
+ help
+ Say Y here if you have the MELFAS MCS-5000 touchscreen controller
+ chip in your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mcs5000_ts.
+
config TOUCHSCREEN_MTOUCH
tristate "MicroTouch serial touchscreens"
select SERIO
To compile this driver as a module, choose M here: the
module will be called mtouch.
+config TOUCHSCREEN_INEXIO
+ tristate "iNexio serial touchscreens"
+ select SERIO
+ help
+ Say Y here if you have an iNexio serial touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called inexio.
+
+config TOUCHSCREEN_INTEL_MID
+ tristate "Intel MID platform resistive touchscreen"
+ depends on INTEL_SCU_IPC
+ help
+ Say Y here if you have a Intel MID based touchscreen in
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called intel_mid_touch.
+
config TOUCHSCREEN_MK712
tristate "ICS MicroClock MK712 touchscreen"
help
module will be called mk712.
config TOUCHSCREEN_HP600
- tristate "HP Jornada 680/690 touchscreen"
+ tristate "HP Jornada 6xx touchscreen"
depends on SH_HP6XX && SH_ADC
help
- Say Y here if you have a HP Jornada 680 or 690 and want to
+ Say Y here if you have a HP Jornada 620/660/680/690 and want to
support the built-in touchscreen.
+ To compile this driver as a module, choose M here: the
+ module will be called hp680_ts_input.
+
+config TOUCHSCREEN_HP7XX
+ tristate "HP Jornada 7xx touchscreen"
+ depends on SA1100_JORNADA720_SSP
+ help
+ Say Y here if you have a HP Jornada 710/720/728 and want
+ to support the built-in touchscreen.
+
+ To compile this driver as a module, choose M here: the
+ module will be called jornada720_ts.
+
+config TOUCHSCREEN_HTCPEN
+ tristate "HTC Shift X9500 touchscreen"
+ depends on ISA
+ help
+ Say Y here if you have an HTC Shift UMPC also known as HTC X9500
+ Clio / Shangrila and want to support the built-in touchscreen.
+
If unsure, say N.
To compile this driver as a module, choose M here: the
- module will be called hp680_ts_input.
+ module will be called htcpen.
config TOUCHSCREEN_PENMOUNT
tristate "Penmount serial touchscreen"
To compile this driver as a module, choose M here: the
module will be called penmount.
+config TOUCHSCREEN_QT602240
+ tristate "QT602240 I2C Touchscreen"
+ depends on I2C
+ help
+ Say Y here if you have the AT42QT602240/ATMXT224 I2C touchscreen
+ connected to your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called qt602240_ts.
+
+config TOUCHSCREEN_MIGOR
+ tristate "Renesas MIGO-R touchscreen"
+ depends on SH_MIGOR && I2C
+ help
+ Say Y here to enable MIGO-R touchscreen support.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called migor_ts.
+
+config TOUCHSCREEN_TNETV107X
+ tristate "TI TNETV107X touchscreen support"
+ depends on ARCH_DAVINCI_TNETV107X
+ help
+ Say Y here if you want to use the TNETV107X touchscreen.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tnetv107x-ts.
+
config TOUCHSCREEN_TOUCHRIGHT
tristate "Touchright serial touchscreen"
select SERIO
To compile this driver as a module, choose M here: the
module will be called touchwin.
+config TOUCHSCREEN_ATMEL_TSADCC
+ tristate "Atmel Touchscreen Interface"
+ depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
+ help
+ Say Y here if you have a 4-wire touchscreen connected to the
+ ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called atmel_tsadcc.
+
config TOUCHSCREEN_UCB1400
tristate "Philips UCB1400 touchscreen"
- select AC97_BUS
+ depends on AC97_BUS
+ depends on UCB1400_CORE
help
This enables support for the Philips UCB1400 touchscreen interface.
The UCB1400 is an AC97 audio codec. The touchscreen interface
To compile this driver as a module, choose M here: the
module will be called ucb1400_ts.
+config TOUCHSCREEN_WM97XX
+ tristate "Support for WM97xx AC97 touchscreen controllers"
+ depends on AC97_BUS
+ help
+ Say Y here if you have a Wolfson Microelectronics WM97xx
+ touchscreen connected to your system. Note that this option
+ only enables core driver, you will also need to select
+ support for appropriate chip below.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called wm97xx-ts.
+
+config TOUCHSCREEN_WM9705
+ bool "WM9705 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ default y
+ help
+ Say Y here to enable support for the Wolfson Microelectronics
+ WM9705 touchscreen controller.
+
+config TOUCHSCREEN_WM9712
+ bool "WM9712 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ default y
+ help
+ Say Y here to enable support for the Wolfson Microelectronics
+ WM9712 touchscreen controller.
+
+config TOUCHSCREEN_WM9713
+ bool "WM9713 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ default y
+ help
+ Say Y here to enable support for the Wolfson Microelectronics
+ WM9713 touchscreen controller.
+
+config TOUCHSCREEN_WM97XX_ATMEL
+ tristate "WM97xx Atmel accelerated touch"
+ depends on TOUCHSCREEN_WM97XX && (AVR32 || ARCH_AT91)
+ help
+ Say Y here for support for streaming mode with WM97xx touchscreens
+ on Atmel AT91 or AVR32 systems with an AC97C module.
+
+ Be aware that this will use channel B in the controller for
+ streaming data, this must not conflict with other AC97C drivers.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the module will
+ be called atmel-wm97xx.
+
+config TOUCHSCREEN_WM97XX_MAINSTONE
+ tristate "WM97xx Mainstone/Palm accelerated touch"
+ depends on TOUCHSCREEN_WM97XX && ARCH_PXA
+ help
+ Say Y here for support for streaming mode with WM97xx touchscreens
+ on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mainstone-wm97xx.
+
+config TOUCHSCREEN_WM97XX_ZYLONITE
+ tristate "Zylonite accelerated touch"
+ depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
+ select TOUCHSCREEN_WM9713
+ help
+ Say Y here for support for streaming mode with the touchscreen
+ on Zylonite systems.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called zylonite-wm97xx.
+
config TOUCHSCREEN_USB_COMPOSITE
tristate "USB Touchscreen Driver"
+ depends on USB_ARCH_HAS_HCD
select USB
help
USB Touchscreen driver for:
- some other eTurboTouch
- Gunze AHL61
- DMC TSC-10/25
+ - IRTOUCHSYSTEMS/UNITOP
+ - IdealTEK URTC1000
+ - GoTop Super_Q2/GogoPen/PenPower tablets
+ - JASTEC USB Touch Controller/DigiTech DTR-02U
+ - Zytronic controllers
Have a look at <http://linux.chapter7.ch/touchkit/> for
a usage description and the required user-space stuff.
To compile this driver as a module, choose M here: the
module will be called usbtouchscreen.
+config TOUCHSCREEN_MC13783
+ tristate "Freescale MC13783 touchscreen input driver"
+ depends on MFD_MC13783
+ help
+ Say Y here if you have an Freescale MC13783 PMIC on your
+ board and want to use its touchscreen
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mc13783_ts.
+
config TOUCHSCREEN_USB_EGALAX
default y
bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
bool "DMC TSC-10/25 device support" if EMBEDDED
depends on TOUCHSCREEN_USB_COMPOSITE
+config TOUCHSCREEN_USB_IRTOUCH
+ default y
+ bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_IDEALTEK
+ default y
+ bool "IdealTEK URTC1000 device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_GENERAL_TOUCH
+ default y
+ bool "GeneralTouch Touchscreen device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_GOTOP
+ default y
+ bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_JASTEC
+ default y
+ bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_E2I
+ default y
+ bool "e2i Touchscreen controller (e.g. from Mimo 740)"
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_ZYTRONIC
+ default y
+ bool "Zytronic controller" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_ETT_TC45USB
+ default y
+ bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_NEXIO
+ default y
+ bool "NEXIO/iNexio device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_TOUCHIT213
+ tristate "Sahara TouchIT-213 touchscreen"
+ select SERIO
+ help
+ Say Y here if you have a Sahara TouchIT-213 Tablet PC.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called touchit213.
+
+config TOUCHSCREEN_TSC2007
+ tristate "TSC2007 based touchscreens"
+ depends on I2C
+ help
+ Say Y here if you have a TSC2007 based touchscreen.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tsc2007.
+
+config TOUCHSCREEN_W90X900
+ tristate "W90P910 touchscreen driver"
+ depends on HAVE_CLK
+ help
+ Say Y here if you have a W90P910 based touchscreen.
+
+ To compile this driver as a module, choose M here: the
+ module will be called w90p910_ts.
+
+config TOUCHSCREEN_PCAP
+ tristate "Motorola PCAP touchscreen"
+ depends on EZX_PCAP
+ help
+ Say Y here if you have a Motorola EZX telephone and
+ want to enable support for the built-in touchscreen.
+
+ To compile this driver as a module, choose M here: the
+ module will be called pcap_ts.
+
+config TOUCHSCREEN_TPS6507X
+ tristate "TPS6507x based touchscreens"
+ depends on I2C
+ help
+ Say Y here if you have a TPS6507x based touchscreen
+ controller.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tps6507x_ts.
+
+config TOUCHSCREEN_STMPE
+ tristate "STMicroelectronics STMPE touchscreens"
+ depends on MFD_STMPE
+ help
+ Say Y here if you want support for STMicroelectronics
+ STMPE touchscreen controllers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called stmpe-ts.
+
endif
projects / linux-flexiantxendom0-natty.git / blobdiff