#ifndef _I915_REG_H_
#define _I915_REG_H_
+#define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a)))
+
/*
* The Bridge device's PCI config space has information about the
* fb aperture size and the amount of pre-reserved memory.
+ * This is all handled in the intel-gtt.ko module. i915.ko only
+ * cares about the vga bit for the vga rbiter.
*/
#define INTEL_GMCH_CTRL 0x52
#define INTEL_GMCH_VGA_DISABLE (1 << 1)
-#define INTEL_GMCH_ENABLED 0x4
-#define INTEL_GMCH_MEM_MASK 0x1
-#define INTEL_GMCH_MEM_64M 0x1
-#define INTEL_GMCH_MEM_128M 0
-
-#define INTEL_GMCH_GMS_MASK (0xf << 4)
-#define INTEL_855_GMCH_GMS_DISABLED (0x0 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_1M (0x1 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_4M (0x2 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_8M (0x3 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_16M (0x4 << 4)
-#define INTEL_855_GMCH_GMS_STOLEN_32M (0x5 << 4)
-
-#define INTEL_915G_GMCH_GMS_STOLEN_48M (0x6 << 4)
-#define INTEL_915G_GMCH_GMS_STOLEN_64M (0x7 << 4)
-#define INTEL_GMCH_GMS_STOLEN_128M (0x8 << 4)
-#define INTEL_GMCH_GMS_STOLEN_256M (0x9 << 4)
-#define INTEL_GMCH_GMS_STOLEN_96M (0xa << 4)
-#define INTEL_GMCH_GMS_STOLEN_160M (0xb << 4)
-#define INTEL_GMCH_GMS_STOLEN_224M (0xc << 4)
-#define INTEL_GMCH_GMS_STOLEN_352M (0xd << 4)
-
-#define SNB_GMCH_CTRL 0x50
-#define SNB_GMCH_GMS_STOLEN_MASK 0xF8
-#define SNB_GMCH_GMS_STOLEN_32M (1 << 3)
-#define SNB_GMCH_GMS_STOLEN_64M (2 << 3)
-#define SNB_GMCH_GMS_STOLEN_96M (3 << 3)
-#define SNB_GMCH_GMS_STOLEN_128M (4 << 3)
-#define SNB_GMCH_GMS_STOLEN_160M (5 << 3)
-#define SNB_GMCH_GMS_STOLEN_192M (6 << 3)
-#define SNB_GMCH_GMS_STOLEN_224M (7 << 3)
-#define SNB_GMCH_GMS_STOLEN_256M (8 << 3)
-#define SNB_GMCH_GMS_STOLEN_288M (9 << 3)
-#define SNB_GMCH_GMS_STOLEN_320M (0xa << 3)
-#define SNB_GMCH_GMS_STOLEN_352M (0xb << 3)
-#define SNB_GMCH_GMS_STOLEN_384M (0xc << 3)
-#define SNB_GMCH_GMS_STOLEN_416M (0xd << 3)
-#define SNB_GMCH_GMS_STOLEN_448M (0xe << 3)
-#define SNB_GMCH_GMS_STOLEN_480M (0xf << 3)
-#define SNB_GMCH_GMS_STOLEN_512M (0x10 << 3)
/* PCI config space */
#define I915_GC_RENDER_CLOCK_200_MHZ (1 << 0)
#define I915_GC_RENDER_CLOCK_333_MHZ (4 << 0)
#define LBB 0xf4
-#define GDRST 0xc0
-#define GDRST_FULL (0<<2)
-#define GDRST_RENDER (1<<2)
-#define GDRST_MEDIA (3<<2)
+
+/* Graphics reset regs */
+#define I965_GDRST 0xc0 /* PCI config register */
+#define ILK_GDSR 0x2ca4 /* MCHBAR offset */
+#define GRDOM_FULL (0<<2)
+#define GRDOM_RENDER (1<<2)
+#define GRDOM_MEDIA (3<<2)
+
+#define GEN6_GDRST 0x941c
+#define GEN6_GRDOM_FULL (1 << 0)
+#define GEN6_GRDOM_RENDER (1 << 1)
+#define GEN6_GRDOM_MEDIA (1 << 2)
+#define GEN6_GRDOM_BLT (1 << 3)
/* VGA stuff */
#define MI_NO_WRITE_FLUSH (1 << 2)
#define MI_SCENE_COUNT (1 << 3) /* just increment scene count */
#define MI_END_SCENE (1 << 4) /* flush binner and incr scene count */
+#define MI_INVALIDATE_ISP (1 << 5) /* invalidate indirect state pointers */
#define MI_BATCH_BUFFER_END MI_INSTR(0x0a, 0)
+#define MI_SUSPEND_FLUSH MI_INSTR(0x0b, 0)
+#define MI_SUSPEND_FLUSH_EN (1<<0)
#define MI_REPORT_HEAD MI_INSTR(0x07, 0)
#define MI_OVERLAY_FLIP MI_INSTR(0x11,0)
#define MI_OVERLAY_CONTINUE (0x0<<21)
#define MI_OVERLAY_OFF (0x2<<21)
#define MI_LOAD_SCAN_LINES_INCL MI_INSTR(0x12, 0)
#define MI_DISPLAY_FLIP MI_INSTR(0x14, 2)
+#define MI_DISPLAY_FLIP_I915 MI_INSTR(0x14, 1)
#define MI_DISPLAY_FLIP_PLANE(n) ((n) << 20)
+#define MI_SET_CONTEXT MI_INSTR(0x18, 0)
+#define MI_MM_SPACE_GTT (1<<8)
+#define MI_MM_SPACE_PHYSICAL (0<<8)
+#define MI_SAVE_EXT_STATE_EN (1<<3)
+#define MI_RESTORE_EXT_STATE_EN (1<<2)
+#define MI_FORCE_RESTORE (1<<1)
+#define MI_RESTORE_INHIBIT (1<<0)
#define MI_STORE_DWORD_IMM MI_INSTR(0x20, 1)
#define MI_MEM_VIRTUAL (1 << 22) /* 965+ only */
#define MI_STORE_DWORD_INDEX MI_INSTR(0x21, 1)
#define MI_STORE_DWORD_INDEX_SHIFT 2
-#define MI_LOAD_REGISTER_IMM MI_INSTR(0x22, 1)
+/* Official intel docs are somewhat sloppy concerning MI_LOAD_REGISTER_IMM:
+ * - Always issue a MI_NOOP _before_ the MI_LOAD_REGISTER_IMM - otherwise hw
+ * simply ignores the register load under certain conditions.
+ * - One can actually load arbitrary many arbitrary registers: Simply issue x
+ * address/value pairs. Don't overdue it, though, x <= 2^4 must hold!
+ */
+#define MI_LOAD_REGISTER_IMM(x) MI_INSTR(0x22, 2*x-1)
+#define MI_FLUSH_DW MI_INSTR(0x26, 1) /* for GEN6 */
+#define MI_INVALIDATE_TLB (1<<18)
+#define MI_INVALIDATE_BSD (1<<7)
#define MI_BATCH_BUFFER MI_INSTR(0x30, 1)
#define MI_BATCH_NON_SECURE (1)
#define MI_BATCH_NON_SECURE_I965 (1<<8)
#define MI_BATCH_BUFFER_START MI_INSTR(0x31, 0)
-
+#define MI_SEMAPHORE_MBOX MI_INSTR(0x16, 1) /* gen6+ */
+#define MI_SEMAPHORE_GLOBAL_GTT (1<<22)
+#define MI_SEMAPHORE_UPDATE (1<<21)
+#define MI_SEMAPHORE_COMPARE (1<<20)
+#define MI_SEMAPHORE_REGISTER (1<<18)
/*
* 3D instructions used by the kernel
*/
#define ASYNC_FLIP (1<<22)
#define DISPLAY_PLANE_A (0<<20)
#define DISPLAY_PLANE_B (1<<20)
+#define GFX_OP_PIPE_CONTROL ((0x3<<29)|(0x3<<27)|(0x2<<24)|2)
+#define PIPE_CONTROL_QW_WRITE (1<<14)
+#define PIPE_CONTROL_DEPTH_STALL (1<<13)
+#define PIPE_CONTROL_WC_FLUSH (1<<12)
+#define PIPE_CONTROL_IS_FLUSH (1<<11) /* MBZ on Ironlake */
+#define PIPE_CONTROL_TC_FLUSH (1<<10) /* GM45+ only */
+#define PIPE_CONTROL_ISP_DIS (1<<9)
+#define PIPE_CONTROL_NOTIFY (1<<8)
+#define PIPE_CONTROL_GLOBAL_GTT (1<<2) /* in addr dword */
+#define PIPE_CONTROL_STALL_EN (1<<1) /* in addr word, Ironlake+ only */
+
+
+/*
+ * Reset registers
+ */
+#define DEBUG_RESET_I830 0x6070
+#define DEBUG_RESET_FULL (1<<7)
+#define DEBUG_RESET_RENDER (1<<8)
+#define DEBUG_RESET_DISPLAY (1<<9)
+
/*
* Fence registers
* Instruction and interrupt control regs
*/
#define PGTBL_ER 0x02024
-#define PRB0_TAIL 0x02030
-#define PRB0_HEAD 0x02034
-#define PRB0_START 0x02038
-#define PRB0_CTL 0x0203c
+#define RENDER_RING_BASE 0x02000
+#define BSD_RING_BASE 0x04000
+#define GEN6_BSD_RING_BASE 0x12000
+#define BLT_RING_BASE 0x22000
+#define RING_TAIL(base) ((base)+0x30)
+#define RING_HEAD(base) ((base)+0x34)
+#define RING_START(base) ((base)+0x38)
+#define RING_CTL(base) ((base)+0x3c)
+#define RING_SYNC_0(base) ((base)+0x40)
+#define RING_SYNC_1(base) ((base)+0x44)
+#define RING_MAX_IDLE(base) ((base)+0x54)
+#define RING_HWS_PGA(base) ((base)+0x80)
+#define RING_HWS_PGA_GEN6(base) ((base)+0x2080)
+#define RING_ACTHD(base) ((base)+0x74)
+#define RING_NOPID(base) ((base)+0x94)
+#define RING_IMR(base) ((base)+0xa8)
#define TAIL_ADDR 0x001FFFF8
#define HEAD_WRAP_COUNT 0xFFE00000
#define HEAD_WRAP_ONE 0x00200000
#define RING_VALID_MASK 0x00000001
#define RING_VALID 0x00000001
#define RING_INVALID 0x00000000
+#define RING_WAIT_I8XX (1<<0) /* gen2, PRBx_HEAD */
+#define RING_WAIT (1<<11) /* gen3+, PRBx_CTL */
+#define RING_WAIT_SEMAPHORE (1<<10) /* gen6+ */
+#if 0
+#define PRB0_TAIL 0x02030
+#define PRB0_HEAD 0x02034
+#define PRB0_START 0x02038
+#define PRB0_CTL 0x0203c
#define PRB1_TAIL 0x02040 /* 915+ only */
#define PRB1_HEAD 0x02044 /* 915+ only */
#define PRB1_START 0x02048 /* 915+ only */
#define PRB1_CTL 0x0204c /* 915+ only */
+#endif
#define IPEIR_I965 0x02064
#define IPEHR_I965 0x02068
#define INSTDONE_I965 0x0206c
#define INSTDONE1 0x0207c /* 965+ only */
#define ACTHD_I965 0x02074
#define HWS_PGA 0x02080
-#define HWS_PGA_GEN6 0x04080
#define HWS_ADDRESS_MASK 0xfffff000
#define HWS_START_ADDRESS_SHIFT 4
#define PWRCTXA 0x2088 /* 965GM+ only */
#define INSTDONE 0x02090
#define NOPID 0x02094
#define HWSTAM 0x02098
+#define VCS_INSTDONE 0x1206C
+#define VCS_IPEIR 0x12064
+#define VCS_IPEHR 0x12068
+#define VCS_ACTHD 0x12074
+#define BCS_INSTDONE 0x2206C
+#define BCS_IPEIR 0x22064
+#define BCS_IPEHR 0x22068
+#define BCS_ACTHD 0x22074
+
+#define ERROR_GEN6 0x040a0
+
+/* GM45+ chicken bits -- debug workaround bits that may be required
+ * for various sorts of correct behavior. The top 16 bits of each are
+ * the enables for writing to the corresponding low bit.
+ */
+#define _3D_CHICKEN 0x02084
+#define _3D_CHICKEN2 0x0208c
+/* Disables pipelining of read flushes past the SF-WIZ interface.
+ * Required on all Ironlake steppings according to the B-Spec, but the
+ * particular danger of not doing so is not specified.
+ */
+# define _3D_CHICKEN2_WM_READ_PIPELINED (1 << 14)
+#define _3D_CHICKEN3 0x02090
#define MI_MODE 0x0209c
# define VS_TIMER_DISPATCH (1 << 6)
+# define MI_FLUSH_ENABLE (1 << 11)
+
+#define GFX_MODE 0x02520
+#define GFX_RUN_LIST_ENABLE (1<<15)
+#define GFX_TLB_INVALIDATE_ALWAYS (1<<13)
+#define GFX_SURFACE_FAULT_ENABLE (1<<12)
+#define GFX_REPLAY_MODE (1<<11)
+#define GFX_PSMI_GRANULARITY (1<<10)
+#define GFX_PPGTT_ENABLE (1<<9)
#define SCPD0 0x0209c /* 915+ only */
#define IER 0x020a0
#define I915_DEBUG_INTERRUPT (1<<2)
#define I915_USER_INTERRUPT (1<<1)
#define I915_ASLE_INTERRUPT (1<<0)
+#define I915_BSD_USER_INTERRUPT (1<<25)
#define EIR 0x020b0
#define EMR 0x020b4
#define ESR 0x020b8
#define I915_ERROR_INSTRUCTION (1<<0)
#define INSTPM 0x020c0
#define INSTPM_SELF_EN (1<<12) /* 915GM only */
+#define INSTPM_AGPBUSY_DIS (1<<11) /* gen3: when disabled, pending interrupts
+ will not assert AGPBUSY# and will only
+ be delivered when out of C3. */
#define ACTHD 0x020c8
#define FW_BLC 0x020d8
-#define FW_BLC2 0x020dc
+#define FW_BLC2 0x020dc
#define FW_BLC_SELF 0x020e0 /* 915+ only */
#define FW_BLC_SELF_EN_MASK (1<<31)
#define FW_BLC_SELF_FIFO_MASK (1<<16) /* 945 only */
#define LM_BURST_LENGTH 0x00000700
#define LM_FIFO_WATERMARK 0x0000001F
#define MI_ARB_STATE 0x020e4 /* 915+ only */
+#define MI_ARB_MASK_SHIFT 16 /* shift for enable bits */
+
+/* Make render/texture TLB fetches lower priorty than associated data
+ * fetches. This is not turned on by default
+ */
+#define MI_ARB_RENDER_TLB_LOW_PRIORITY (1 << 15)
+
+/* Isoch request wait on GTT enable (Display A/B/C streams).
+ * Make isoch requests stall on the TLB update. May cause
+ * display underruns (test mode only)
+ */
+#define MI_ARB_ISOCH_WAIT_GTT (1 << 14)
+
+/* Block grant count for isoch requests when block count is
+ * set to a finite value.
+ */
+#define MI_ARB_BLOCK_GRANT_MASK (3 << 12)
+#define MI_ARB_BLOCK_GRANT_8 (0 << 12) /* for 3 display planes */
+#define MI_ARB_BLOCK_GRANT_4 (1 << 12) /* for 2 display planes */
+#define MI_ARB_BLOCK_GRANT_2 (2 << 12) /* for 1 display plane */
+#define MI_ARB_BLOCK_GRANT_0 (3 << 12) /* don't use */
+
+/* Enable render writes to complete in C2/C3/C4 power states.
+ * If this isn't enabled, render writes are prevented in low
+ * power states. That seems bad to me.
+ */
+#define MI_ARB_C3_LP_WRITE_ENABLE (1 << 11)
+
+/* This acknowledges an async flip immediately instead
+ * of waiting for 2TLB fetches.
+ */
+#define MI_ARB_ASYNC_FLIP_ACK_IMMEDIATE (1 << 10)
+
+/* Enables non-sequential data reads through arbiter
+ */
+#define MI_ARB_DUAL_DATA_PHASE_DISABLE (1 << 9)
+
+/* Disable FSB snooping of cacheable write cycles from binner/render
+ * command stream
+ */
+#define MI_ARB_CACHE_SNOOP_DISABLE (1 << 8)
+
+/* Arbiter time slice for non-isoch streams */
+#define MI_ARB_TIME_SLICE_MASK (7 << 5)
+#define MI_ARB_TIME_SLICE_1 (0 << 5)
+#define MI_ARB_TIME_SLICE_2 (1 << 5)
+#define MI_ARB_TIME_SLICE_4 (2 << 5)
+#define MI_ARB_TIME_SLICE_6 (3 << 5)
+#define MI_ARB_TIME_SLICE_8 (4 << 5)
+#define MI_ARB_TIME_SLICE_10 (5 << 5)
+#define MI_ARB_TIME_SLICE_14 (6 << 5)
+#define MI_ARB_TIME_SLICE_16 (7 << 5)
+
+/* Low priority grace period page size */
+#define MI_ARB_LOW_PRIORITY_GRACE_4KB (0 << 4) /* default */
+#define MI_ARB_LOW_PRIORITY_GRACE_8KB (1 << 4)
+
+/* Disable display A/B trickle feed */
+#define MI_ARB_DISPLAY_TRICKLE_FEED_DISABLE (1 << 2)
+
+/* Set display plane priority */
+#define MI_ARB_DISPLAY_PRIORITY_A_B (0 << 0) /* display A > display B */
+#define MI_ARB_DISPLAY_PRIORITY_B_A (1 << 0) /* display B > display A */
+
#define CACHE_MODE_0 0x02120 /* 915+ only */
#define CM0_MASK_SHIFT 16
#define CM0_IZ_OPT_DISABLE (1<<6)
#define CM0_RC_OP_FLUSH_DISABLE (1<<0)
#define BB_ADDR 0x02140 /* 8 bytes */
#define GFX_FLSH_CNTL 0x02170 /* 915+ only */
-
+#define ECOSKPD 0x021d0
+#define ECO_GATING_CX_ONLY (1<<3)
+#define ECO_FLIP_DONE (1<<0)
+
+/* GEN6 interrupt control */
+#define GEN6_RENDER_HWSTAM 0x2098
+#define GEN6_RENDER_IMR 0x20a8
+#define GEN6_RENDER_CONTEXT_SWITCH_INTERRUPT (1 << 8)
+#define GEN6_RENDER_PPGTT_PAGE_FAULT (1 << 7)
+#define GEN6_RENDER_TIMEOUT_COUNTER_EXPIRED (1 << 6)
+#define GEN6_RENDER_L3_PARITY_ERROR (1 << 5)
+#define GEN6_RENDER_PIPE_CONTROL_NOTIFY_INTERRUPT (1 << 4)
+#define GEN6_RENDER_COMMAND_PARSER_MASTER_ERROR (1 << 3)
+#define GEN6_RENDER_SYNC_STATUS (1 << 2)
+#define GEN6_RENDER_DEBUG_INTERRUPT (1 << 1)
+#define GEN6_RENDER_USER_INTERRUPT (1 << 0)
+
+#define GEN6_BLITTER_HWSTAM 0x22098
+#define GEN6_BLITTER_IMR 0x220a8
+#define GEN6_BLITTER_MI_FLUSH_DW_NOTIFY_INTERRUPT (1 << 26)
+#define GEN6_BLITTER_COMMAND_PARSER_MASTER_ERROR (1 << 25)
+#define GEN6_BLITTER_SYNC_STATUS (1 << 24)
+#define GEN6_BLITTER_USER_INTERRUPT (1 << 22)
+
+#define GEN6_BLITTER_ECOSKPD 0x221d0
+#define GEN6_BLITTER_LOCK_SHIFT 16
+#define GEN6_BLITTER_FBC_NOTIFY (1<<3)
+
+#define GEN6_BSD_SLEEP_PSMI_CONTROL 0x12050
+#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_MODIFY_MASK (1 << 16)
+#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_DISABLE (1 << 0)
+#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_ENABLE 0
+#define GEN6_BSD_SLEEP_PSMI_CONTROL_IDLE_INDICATOR (1 << 3)
+
+#define GEN6_BSD_IMR 0x120a8
+#define GEN6_BSD_USER_INTERRUPT (1 << 12)
+
+#define GEN6_BSD_RNCID 0x12198
/*
* Framebuffer compression (915+ only)
#define DPFC_CHICKEN 0x3224
#define DPFC_HT_MODIFY (1<<31)
+/* Framebuffer compression for Ironlake */
+#define ILK_DPFC_CB_BASE 0x43200
+#define ILK_DPFC_CONTROL 0x43208
+/* The bit 28-8 is reserved */
+#define DPFC_RESERVED (0x1FFFFF00)
+#define ILK_DPFC_RECOMP_CTL 0x4320c
+#define ILK_DPFC_STATUS 0x43210
+#define ILK_DPFC_FENCE_YOFF 0x43218
+#define ILK_DPFC_CHICKEN 0x43224
+#define ILK_FBC_RT_BASE 0x2128
+#define ILK_FBC_RT_VALID (1<<0)
+
+#define ILK_DISPLAY_CHICKEN1 0x42000
+#define ILK_FBCQ_DIS (1<<22)
+#define ILK_PABSTRETCH_DIS (1<<21)
+
+
+/*
+ * Framebuffer compression for Sandybridge
+ *
+ * The following two registers are of type GTTMMADR
+ */
+#define SNB_DPFC_CTL_SA 0x100100
+#define SNB_CPU_FENCE_ENABLE (1<<29)
+#define DPFC_CPU_FENCE_OFFSET 0x100104
+
+
/*
* GPIO regs
*/
# define GPIO_DATA_VAL_IN (1 << 12)
# define GPIO_DATA_PULLUP_DISABLE (1 << 13)
-#define GMBUS0 0x5100
-#define GMBUS1 0x5104
-#define GMBUS2 0x5108
-#define GMBUS3 0x510c
-#define GMBUS4 0x5110
-#define GMBUS5 0x5120
+#define GMBUS0 0x5100 /* clock/port select */
+#define GMBUS_RATE_100KHZ (0<<8)
+#define GMBUS_RATE_50KHZ (1<<8)
+#define GMBUS_RATE_400KHZ (2<<8) /* reserved on Pineview */
+#define GMBUS_RATE_1MHZ (3<<8) /* reserved on Pineview */
+#define GMBUS_HOLD_EXT (1<<7) /* 300ns hold time, rsvd on Pineview */
+#define GMBUS_PORT_DISABLED 0
+#define GMBUS_PORT_SSC 1
+#define GMBUS_PORT_VGADDC 2
+#define GMBUS_PORT_PANEL 3
+#define GMBUS_PORT_DPC 4 /* HDMIC */
+#define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */
+ /* 6 reserved */
+#define GMBUS_PORT_DPD 7 /* HDMID */
+#define GMBUS_NUM_PORTS 8
+#define GMBUS1 0x5104 /* command/status */
+#define GMBUS_SW_CLR_INT (1<<31)
+#define GMBUS_SW_RDY (1<<30)
+#define GMBUS_ENT (1<<29) /* enable timeout */
+#define GMBUS_CYCLE_NONE (0<<25)
+#define GMBUS_CYCLE_WAIT (1<<25)
+#define GMBUS_CYCLE_INDEX (2<<25)
+#define GMBUS_CYCLE_STOP (4<<25)
+#define GMBUS_BYTE_COUNT_SHIFT 16
+#define GMBUS_SLAVE_INDEX_SHIFT 8
+#define GMBUS_SLAVE_ADDR_SHIFT 1
+#define GMBUS_SLAVE_READ (1<<0)
+#define GMBUS_SLAVE_WRITE (0<<0)
+#define GMBUS2 0x5108 /* status */
+#define GMBUS_INUSE (1<<15)
+#define GMBUS_HW_WAIT_PHASE (1<<14)
+#define GMBUS_STALL_TIMEOUT (1<<13)
+#define GMBUS_INT (1<<12)
+#define GMBUS_HW_RDY (1<<11)
+#define GMBUS_SATOER (1<<10)
+#define GMBUS_ACTIVE (1<<9)
+#define GMBUS3 0x510c /* data buffer bytes 3-0 */
+#define GMBUS4 0x5110 /* interrupt mask (Pineview+) */
+#define GMBUS_SLAVE_TIMEOUT_EN (1<<4)
+#define GMBUS_NAK_EN (1<<3)
+#define GMBUS_IDLE_EN (1<<2)
+#define GMBUS_HW_WAIT_EN (1<<1)
+#define GMBUS_HW_RDY_EN (1<<0)
+#define GMBUS5 0x5120 /* byte index */
+#define GMBUS_2BYTE_INDEX_EN (1<<31)
/*
* Clock control & power management
#define VGA1_PD_P1_MASK (0x1f << 8)
#define DPLL_A 0x06014
#define DPLL_B 0x06018
+#define DPLL(pipe) _PIPE(pipe, DPLL_A, DPLL_B)
#define DPLL_VCO_ENABLE (1 << 31)
#define DPLL_DVO_HIGH_SPEED (1 << 30)
#define DPLL_SYNCLOCK_ENABLE (1 << 29)
#define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */
#define DPLL_FPA01_P1_POST_DIV_MASK_PINEVIEW 0x00ff8000 /* Pineview */
-#define I915_FIFO_UNDERRUN_STATUS (1UL<<31)
-#define I915_CRC_ERROR_ENABLE (1UL<<29)
-#define I915_CRC_DONE_ENABLE (1UL<<28)
-#define I915_GMBUS_EVENT_ENABLE (1UL<<27)
-#define I915_VSYNC_INTERRUPT_ENABLE (1UL<<25)
-#define I915_DISPLAY_LINE_COMPARE_ENABLE (1UL<<24)
-#define I915_DPST_EVENT_ENABLE (1UL<<23)
-#define I915_LEGACY_BLC_EVENT_ENABLE (1UL<<22)
-#define I915_ODD_FIELD_INTERRUPT_ENABLE (1UL<<21)
-#define I915_EVEN_FIELD_INTERRUPT_ENABLE (1UL<<20)
-#define I915_START_VBLANK_INTERRUPT_ENABLE (1UL<<18) /* 965 or later */
-#define I915_VBLANK_INTERRUPT_ENABLE (1UL<<17)
-#define I915_OVERLAY_UPDATED_ENABLE (1UL<<16)
-#define I915_CRC_ERROR_INTERRUPT_STATUS (1UL<<13)
-#define I915_CRC_DONE_INTERRUPT_STATUS (1UL<<12)
-#define I915_GMBUS_INTERRUPT_STATUS (1UL<<11)
-#define I915_VSYNC_INTERRUPT_STATUS (1UL<<9)
-#define I915_DISPLAY_LINE_COMPARE_STATUS (1UL<<8)
-#define I915_DPST_EVENT_STATUS (1UL<<7)
-#define I915_LEGACY_BLC_EVENT_STATUS (1UL<<6)
-#define I915_ODD_FIELD_INTERRUPT_STATUS (1UL<<5)
-#define I915_EVEN_FIELD_INTERRUPT_STATUS (1UL<<4)
-#define I915_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */
-#define I915_VBLANK_INTERRUPT_STATUS (1UL<<1)
-#define I915_OVERLAY_UPDATED_STATUS (1UL<<0)
-
#define SRX_INDEX 0x3c4
#define SRX_DATA 0x3c5
#define SR01 1
#define LVDS 0x61180
#define LVDS_ON (1<<31)
-#define ADPA 0x61100
-#define ADPA_DPMS_MASK (~(3<<10))
-#define ADPA_DPMS_ON (0<<10)
-#define ADPA_DPMS_SUSPEND (1<<10)
-#define ADPA_DPMS_STANDBY (2<<10)
-#define ADPA_DPMS_OFF (3<<10)
-
-#define RING_TAIL 0x00
-#define TAIL_ADDR 0x001FFFF8
-#define RING_HEAD 0x04
-#define HEAD_WRAP_COUNT 0xFFE00000
-#define HEAD_WRAP_ONE 0x00200000
-#define HEAD_ADDR 0x001FFFFC
-#define RING_START 0x08
-#define START_ADDR 0xFFFFF000
-#define RING_LEN 0x0C
-#define RING_NR_PAGES 0x001FF000
-#define RING_REPORT_MASK 0x00000006
-#define RING_REPORT_64K 0x00000002
-#define RING_REPORT_128K 0x00000004
-#define RING_NO_REPORT 0x00000000
-#define RING_VALID_MASK 0x00000001
-#define RING_VALID 0x00000001
-#define RING_INVALID 0x00000000
-
/* Scratch pad debug 0 reg:
*/
#define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000
#define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f
#define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0
#define DPLL_B_MD 0x06020 /* 965+ only */
+#define DPLL_MD(pipe) _PIPE(pipe, DPLL_A_MD, DPLL_B_MD)
#define FPA0 0x06040
#define FPA1 0x06044
#define FPB0 0x06048
#define FPB1 0x0604c
+#define FP0(pipe) _PIPE(pipe, FPA0, FPB0)
+#define FP1(pipe) _PIPE(pipe, FPA1, FPB1)
#define FP_N_DIV_MASK 0x003f0000
#define FP_N_PINEVIEW_DIV_MASK 0x00ff0000
#define FP_N_DIV_SHIFT 16
#define DPLLA_TEST_M_BYPASS (1 << 2)
#define DPLLA_INPUT_BUFFER_ENABLE (1 << 0)
#define D_STATE 0x6104
+#define DSTATE_GFX_RESET_I830 (1<<6)
#define DSTATE_PLL_D3_OFF (1<<3)
#define DSTATE_GFX_CLOCK_GATING (1<<1)
#define DSTATE_DOT_CLOCK_GATING (1<<0)
*/
#define MCHBAR_MIRROR_BASE 0x10000
+#define MCHBAR_MIRROR_BASE_SNB 0x140000
+
/** 915-945 and GM965 MCH register controlling DRAM channel access */
#define DCC 0x10200
#define DCC_ADDRESSING_MODE_SINGLE_CHANNEL (0 << 0)
#define DCC_CHANNEL_XOR_DISABLE (1 << 10)
#define DCC_CHANNEL_XOR_BIT_17 (1 << 9)
+/** Pineview MCH register contains DDR3 setting */
+#define CSHRDDR3CTL 0x101a8
+#define CSHRDDR3CTL_DDR3 (1 << 2)
+
/** 965 MCH register controlling DRAM channel configuration */
#define C0DRB3 0x10206
#define C1DRB3 0x10606
#define CLKCFG_MEM_800 (3 << 4)
#define CLKCFG_MEM_MASK (7 << 4)
+#define TSC1 0x11001
+#define TSE (1<<0)
+#define TR1 0x11006
+#define TSFS 0x11020
+#define TSFS_SLOPE_MASK 0x0000ff00
+#define TSFS_SLOPE_SHIFT 8
+#define TSFS_INTR_MASK 0x000000ff
+
#define CRSTANDVID 0x11100
#define PXVFREQ_BASE 0x11110 /* P[0-15]VIDFREQ (0x1114c) (Ironlake) */
#define PXVFREQ_PX_MASK 0x7f000000
#define RCBMINAVG 0x111a0
#define RCUPEI 0x111b0
#define RCDNEI 0x111b4
-#define MCHBAR_RENDER_STANDBY 0x111b8
-#define RCX_SW_EXIT (1<<23)
-#define RSX_STATUS_MASK 0x00700000
+#define RSTDBYCTL 0x111b8
+#define RS1EN (1<<31)
+#define RS2EN (1<<30)
+#define RS3EN (1<<29)
+#define D3RS3EN (1<<28) /* Display D3 imlies RS3 */
+#define SWPROMORSX (1<<27) /* RSx promotion timers ignored */
+#define RCWAKERW (1<<26) /* Resetwarn from PCH causes wakeup */
+#define DPRSLPVREN (1<<25) /* Fast voltage ramp enable */
+#define GFXTGHYST (1<<24) /* Hysteresis to allow trunk gating */
+#define RCX_SW_EXIT (1<<23) /* Leave RSx and prevent re-entry */
+#define RSX_STATUS_MASK (7<<20)
+#define RSX_STATUS_ON (0<<20)
+#define RSX_STATUS_RC1 (1<<20)
+#define RSX_STATUS_RC1E (2<<20)
+#define RSX_STATUS_RS1 (3<<20)
+#define RSX_STATUS_RS2 (4<<20) /* aka rc6 */
+#define RSX_STATUS_RSVD (5<<20) /* deep rc6 unsupported on ilk */
+#define RSX_STATUS_RS3 (6<<20) /* rs3 unsupported on ilk */
+#define RSX_STATUS_RSVD2 (7<<20)
+#define UWRCRSXE (1<<19) /* wake counter limit prevents rsx */
+#define RSCRP (1<<18) /* rs requests control on rs1/2 reqs */
+#define JRSC (1<<17) /* rsx coupled to cpu c-state */
+#define RS2INC0 (1<<16) /* allow rs2 in cpu c0 */
+#define RS1CONTSAV_MASK (3<<14)
+#define RS1CONTSAV_NO_RS1 (0<<14) /* rs1 doesn't save/restore context */
+#define RS1CONTSAV_RSVD (1<<14)
+#define RS1CONTSAV_SAVE_RS1 (2<<14) /* rs1 saves context */
+#define RS1CONTSAV_FULL_RS1 (3<<14) /* rs1 saves and restores context */
+#define NORMSLEXLAT_MASK (3<<12)
+#define SLOW_RS123 (0<<12)
+#define SLOW_RS23 (1<<12)
+#define SLOW_RS3 (2<<12)
+#define NORMAL_RS123 (3<<12)
+#define RCMODE_TIMEOUT (1<<11) /* 0 is eval interval method */
+#define IMPROMOEN (1<<10) /* promo is immediate or delayed until next idle interval (only for timeout method above) */
+#define RCENTSYNC (1<<9) /* rs coupled to cpu c-state (3/6/7) */
+#define STATELOCK (1<<7) /* locked to rs_cstate if 0 */
+#define RS_CSTATE_MASK (3<<4)
+#define RS_CSTATE_C367_RS1 (0<<4)
+#define RS_CSTATE_C36_RS1_C7_RS2 (1<<4)
+#define RS_CSTATE_RSVD (2<<4)
+#define RS_CSTATE_C367_RS2 (3<<4)
+#define REDSAVES (1<<3) /* no context save if was idle during rs0 */
+#define REDRESTORES (1<<2) /* no restore if was idle during rs0 */
#define VIDCTL 0x111c0
#define VIDSTS 0x111c8
#define VIDSTART 0x111cc /* 8 bits */
#define MEMSTAT_SRC_CTL_STDBY 3
#define RCPREVBSYTUPAVG 0x113b8
#define RCPREVBSYTDNAVG 0x113bc
+#define PMMISC 0x11214
+#define MCPPCE_EN (1<<0) /* enable PM_MSG from PCH->MPC */
+#define SDEW 0x1124c
+#define CSIEW0 0x11250
+#define CSIEW1 0x11254
+#define CSIEW2 0x11258
+#define PEW 0x1125c
+#define DEW 0x11270
+#define MCHAFE 0x112c0
+#define CSIEC 0x112e0
+#define DMIEC 0x112e4
+#define DDREC 0x112e8
+#define PEG0EC 0x112ec
+#define PEG1EC 0x112f0
+#define GFXEC 0x112f4
+#define RPPREVBSYTUPAVG 0x113b8
+#define RPPREVBSYTDNAVG 0x113bc
+#define ECR 0x11600
+#define ECR_GPFE (1<<31)
+#define ECR_IMONE (1<<30)
+#define ECR_CAP_MASK 0x0000001f /* Event range, 0-31 */
+#define OGW0 0x11608
+#define OGW1 0x1160c
+#define EG0 0x11610
+#define EG1 0x11614
+#define EG2 0x11618
+#define EG3 0x1161c
+#define EG4 0x11620
+#define EG5 0x11624
+#define EG6 0x11628
+#define EG7 0x1162c
+#define PXW 0x11664
+#define PXWL 0x11680
+#define LCFUSE02 0x116c0
+#define LCFUSE_HIV_MASK 0x000000ff
+#define CSIPLL0 0x12c10
+#define DDRMPLL1 0X12c20
#define PEG_BAND_GAP_DATA 0x14d68
+#define GEN6_GT_PERF_STATUS 0x145948
+#define GEN6_RP_STATE_LIMITS 0x145994
+#define GEN6_RP_STATE_CAP 0x145998
+
+/*
+ * Logical Context regs
+ */
+#define CCID 0x2180
+#define CCID_EN (1<<0)
/*
* Overlay regs
*/
#define PIPEBSRC 0x6101c
#define BCLRPAT_B 0x61020
+#define HTOTAL(pipe) _PIPE(pipe, HTOTAL_A, HTOTAL_B)
+#define HBLANK(pipe) _PIPE(pipe, HBLANK_A, HBLANK_B)
+#define HSYNC(pipe) _PIPE(pipe, HSYNC_A, HSYNC_B)
+#define VTOTAL(pipe) _PIPE(pipe, VTOTAL_A, VTOTAL_B)
+#define VBLANK(pipe) _PIPE(pipe, VBLANK_A, VBLANK_B)
+#define VSYNC(pipe) _PIPE(pipe, VSYNC_A, VSYNC_B)
+#define BCLRPAT(pipe) _PIPE(pipe, BCLRPAT_A, BCLRPAT_B)
+
/* VGA port control */
#define ADPA 0x61100
#define ADPA_DAC_ENABLE (1<<31)
#define ADPA_DPMS_STANDBY (2<<10)
#define ADPA_DPMS_OFF (3<<10)
+
/* Hotplug control (945+ only) */
#define PORT_HOTPLUG_EN 0x61110
#define HDMIB_HOTPLUG_INT_EN (1 << 29)
#define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4)
#define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2)
#define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2)
-#define CRT_HOTPLUG_MASK (0x3fc) /* Bits 9-2 */
-#define CRT_FORCE_HOTPLUG_MASK 0xfffffe1f
#define PORT_HOTPLUG_STAT 0x61114
#define HDMIB_HOTPLUG_INT_STATUS (1 << 29)
#define LVDS_B0B3_POWER_DOWN (0 << 2)
#define LVDS_B0B3_POWER_UP (3 << 2)
+/* Video Data Island Packet control */
+#define VIDEO_DIP_DATA 0x61178
+#define VIDEO_DIP_CTL 0x61170
+#define VIDEO_DIP_ENABLE (1 << 31)
+#define VIDEO_DIP_PORT_B (1 << 29)
+#define VIDEO_DIP_PORT_C (2 << 29)
+#define VIDEO_DIP_ENABLE_AVI (1 << 21)
+#define VIDEO_DIP_ENABLE_VENDOR (2 << 21)
+#define VIDEO_DIP_ENABLE_SPD (8 << 21)
+#define VIDEO_DIP_SELECT_AVI (0 << 19)
+#define VIDEO_DIP_SELECT_VENDOR (1 << 19)
+#define VIDEO_DIP_SELECT_SPD (3 << 19)
+#define VIDEO_DIP_FREQ_ONCE (0 << 16)
+#define VIDEO_DIP_FREQ_VSYNC (1 << 16)
+#define VIDEO_DIP_FREQ_2VSYNC (2 << 16)
+
/* Panel power sequencing */
#define PP_STATUS 0x61200
#define PP_ON (1 << 31)
#define PP_SEQUENCE_ON (1 << 28)
#define PP_SEQUENCE_OFF (2 << 28)
#define PP_SEQUENCE_MASK 0x30000000
+#define PP_CYCLE_DELAY_ACTIVE (1 << 27)
+#define PP_SEQUENCE_STATE_ON_IDLE (1 << 3)
+#define PP_SEQUENCE_STATE_MASK 0x0000000f
#define PP_CONTROL 0x61204
#define POWER_TARGET_ON (1 << 0)
#define PP_ON_DELAYS 0x61208
# define TV_TEST_MODE_MASK (7 << 0)
#define TV_DAC 0x68004
+# define TV_DAC_SAVE 0x00ffff00
/**
* Reports that DAC state change logic has reported change (RO).
*
#define DP_LINK_TRAIN_MASK (3 << 28)
#define DP_LINK_TRAIN_SHIFT 28
+/* CPT Link training mode */
+#define DP_LINK_TRAIN_PAT_1_CPT (0 << 8)
+#define DP_LINK_TRAIN_PAT_2_CPT (1 << 8)
+#define DP_LINK_TRAIN_PAT_IDLE_CPT (2 << 8)
+#define DP_LINK_TRAIN_OFF_CPT (3 << 8)
+#define DP_LINK_TRAIN_MASK_CPT (7 << 8)
+#define DP_LINK_TRAIN_SHIFT_CPT 8
+
/* Signal voltages. These are mostly controlled by the other end */
#define DP_VOLTAGE_0_4 (0 << 25)
#define DP_VOLTAGE_0_6 (1 << 25)
/* Display & cursor control */
-/* dithering flag on Ironlake */
-#define PIPE_ENABLE_DITHER (1 << 4)
/* Pipe A */
#define PIPEADSL 0x70000
+#define DSL_LINEMASK 0x00000fff
#define PIPEACONF 0x70008
-#define PIPEACONF_ENABLE (1<<31)
-#define PIPEACONF_DISABLE 0
-#define PIPEACONF_DOUBLE_WIDE (1<<30)
+#define PIPECONF_ENABLE (1<<31)
+#define PIPECONF_DISABLE 0
+#define PIPECONF_DOUBLE_WIDE (1<<30)
#define I965_PIPECONF_ACTIVE (1<<30)
-#define PIPEACONF_SINGLE_WIDE 0
-#define PIPEACONF_PIPE_UNLOCKED 0
-#define PIPEACONF_PIPE_LOCKED (1<<25)
-#define PIPEACONF_PALETTE 0
-#define PIPEACONF_GAMMA (1<<24)
+#define PIPECONF_SINGLE_WIDE 0
+#define PIPECONF_PIPE_UNLOCKED 0
+#define PIPECONF_PIPE_LOCKED (1<<25)
+#define PIPECONF_PALETTE 0
+#define PIPECONF_GAMMA (1<<24)
#define PIPECONF_FORCE_BORDER (1<<25)
#define PIPECONF_PROGRESSIVE (0 << 21)
#define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21)
#define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21)
#define PIPECONF_CXSR_DOWNCLOCK (1<<16)
+#define PIPECONF_BPP_MASK (0x000000e0)
+#define PIPECONF_BPP_8 (0<<5)
+#define PIPECONF_BPP_10 (1<<5)
+#define PIPECONF_BPP_6 (2<<5)
+#define PIPECONF_BPP_12 (3<<5)
+#define PIPECONF_DITHER_EN (1<<4)
+#define PIPECONF_DITHER_TYPE_MASK (0x0000000c)
+#define PIPECONF_DITHER_TYPE_SP (0<<2)
+#define PIPECONF_DITHER_TYPE_ST1 (1<<2)
+#define PIPECONF_DITHER_TYPE_ST2 (2<<2)
+#define PIPECONF_DITHER_TYPE_TEMP (3<<2)
#define PIPEASTAT 0x70024
#define PIPE_FIFO_UNDERRUN_STATUS (1UL<<31)
#define PIPE_CRC_ERROR_ENABLE (1UL<<29)
#define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */
#define PIPE_VBLANK_INTERRUPT_STATUS (1UL<<1)
#define PIPE_OVERLAY_UPDATED_STATUS (1UL<<0)
-#define PIPE_BPC_MASK (7 << 5) /* Ironlake */
+#define PIPE_BPC_MASK (7 << 5) /* Ironlake */
#define PIPE_8BPC (0 << 5)
#define PIPE_10BPC (1 << 5)
#define PIPE_6BPC (2 << 5)
#define PIPE_12BPC (3 << 5)
+#define PIPESRC(pipe) _PIPE(pipe, PIPEASRC, PIPEBSRC)
+#define PIPECONF(pipe) _PIPE(pipe, PIPEACONF, PIPEBCONF)
+#define PIPEDSL(pipe) _PIPE(pipe, PIPEADSL, PIPEBDSL)
+#define PIPEFRAMEPIXEL(pipe) _PIPE(pipe, PIPEAFRAMEPIXEL, PIPEBFRAMEPIXEL)
+
#define DSPARB 0x70030
#define DSPARB_CSTART_MASK (0x7f << 7)
#define DSPARB_CSTART_SHIFT 7
#define DSPFW1 0x70034
#define DSPFW_SR_SHIFT 23
+#define DSPFW_SR_MASK (0x1ff<<23)
#define DSPFW_CURSORB_SHIFT 16
+#define DSPFW_CURSORB_MASK (0x3f<<16)
#define DSPFW_PLANEB_SHIFT 8
+#define DSPFW_PLANEB_MASK (0x7f<<8)
+#define DSPFW_PLANEA_MASK (0x7f)
#define DSPFW2 0x70038
#define DSPFW_CURSORA_MASK 0x00003f00
#define DSPFW_CURSORA_SHIFT 8
+#define DSPFW_PLANEC_MASK (0x7f)
#define DSPFW3 0x7003c
#define DSPFW_HPLL_SR_EN (1<<31)
#define DSPFW_CURSOR_SR_SHIFT 24
#define PINEVIEW_SELF_REFRESH_EN (1<<30)
+#define DSPFW_CURSOR_SR_MASK (0x3f<<24)
+#define DSPFW_HPLL_CURSOR_SHIFT 16
+#define DSPFW_HPLL_CURSOR_MASK (0x3f<<16)
+#define DSPFW_HPLL_SR_MASK (0x1ff)
/* FIFO watermark sizes etc */
#define G4X_FIFO_LINE_SIZE 64
#define I830_FIFO_LINE_SIZE 32
#define G4X_FIFO_SIZE 127
-#define I945_FIFO_SIZE 127 /* 945 & 965 */
+#define I965_FIFO_SIZE 512
+#define I945_FIFO_SIZE 127
#define I915_FIFO_SIZE 95
#define I855GM_FIFO_SIZE 127 /* In cachelines */
#define I830_FIFO_SIZE 95
#define PINEVIEW_CURSOR_DFT_WM 0
#define PINEVIEW_CURSOR_GUARD_WM 5
+#define I965_CURSOR_FIFO 64
+#define I965_CURSOR_MAX_WM 32
+#define I965_CURSOR_DFT_WM 8
+
+/* define the Watermark register on Ironlake */
+#define WM0_PIPEA_ILK 0x45100
+#define WM0_PIPE_PLANE_MASK (0x7f<<16)
+#define WM0_PIPE_PLANE_SHIFT 16
+#define WM0_PIPE_SPRITE_MASK (0x3f<<8)
+#define WM0_PIPE_SPRITE_SHIFT 8
+#define WM0_PIPE_CURSOR_MASK (0x1f)
+
+#define WM0_PIPEB_ILK 0x45104
+#define WM1_LP_ILK 0x45108
+#define WM1_LP_SR_EN (1<<31)
+#define WM1_LP_LATENCY_SHIFT 24
+#define WM1_LP_LATENCY_MASK (0x7f<<24)
+#define WM1_LP_FBC_MASK (0xf<<20)
+#define WM1_LP_FBC_SHIFT 20
+#define WM1_LP_SR_MASK (0x1ff<<8)
+#define WM1_LP_SR_SHIFT 8
+#define WM1_LP_CURSOR_MASK (0x3f)
+#define WM2_LP_ILK 0x4510c
+#define WM2_LP_EN (1<<31)
+#define WM3_LP_ILK 0x45110
+#define WM3_LP_EN (1<<31)
+#define WM1S_LP_ILK 0x45120
+#define WM1S_LP_EN (1<<31)
+
+/* Memory latency timer register */
+#define MLTR_ILK 0x11222
+#define MLTR_WM1_SHIFT 0
+#define MLTR_WM2_SHIFT 8
+/* the unit of memory self-refresh latency time is 0.5us */
+#define ILK_SRLT_MASK 0x3f
+#define ILK_LATENCY(shift) (I915_READ(MLTR_ILK) >> (shift) & ILK_SRLT_MASK)
+#define ILK_READ_WM1_LATENCY() ILK_LATENCY(MLTR_WM1_SHIFT)
+#define ILK_READ_WM2_LATENCY() ILK_LATENCY(MLTR_WM2_SHIFT)
+
+/* define the fifo size on Ironlake */
+#define ILK_DISPLAY_FIFO 128
+#define ILK_DISPLAY_MAXWM 64
+#define ILK_DISPLAY_DFTWM 8
+#define ILK_CURSOR_FIFO 32
+#define ILK_CURSOR_MAXWM 16
+#define ILK_CURSOR_DFTWM 8
+
+#define ILK_DISPLAY_SR_FIFO 512
+#define ILK_DISPLAY_MAX_SRWM 0x1ff
+#define ILK_DISPLAY_DFT_SRWM 0x3f
+#define ILK_CURSOR_SR_FIFO 64
+#define ILK_CURSOR_MAX_SRWM 0x3f
+#define ILK_CURSOR_DFT_SRWM 8
+
+#define ILK_FIFO_LINE_SIZE 64
+
+/* define the WM info on Sandybridge */
+#define SNB_DISPLAY_FIFO 128
+#define SNB_DISPLAY_MAXWM 0x7f /* bit 16:22 */
+#define SNB_DISPLAY_DFTWM 8
+#define SNB_CURSOR_FIFO 32
+#define SNB_CURSOR_MAXWM 0x1f /* bit 4:0 */
+#define SNB_CURSOR_DFTWM 8
+
+#define SNB_DISPLAY_SR_FIFO 512
+#define SNB_DISPLAY_MAX_SRWM 0x1ff /* bit 16:8 */
+#define SNB_DISPLAY_DFT_SRWM 0x3f
+#define SNB_CURSOR_SR_FIFO 64
+#define SNB_CURSOR_MAX_SRWM 0x3f /* bit 5:0 */
+#define SNB_CURSOR_DFT_SRWM 8
+
+#define SNB_FBC_MAX_SRWM 0xf /* bit 23:20 */
+
+#define SNB_FIFO_LINE_SIZE 64
+
+
+/* the address where we get all kinds of latency value */
+#define SSKPD 0x5d10
+#define SSKPD_WM_MASK 0x3f
+#define SSKPD_WM0_SHIFT 0
+#define SSKPD_WM1_SHIFT 8
+#define SSKPD_WM2_SHIFT 16
+#define SSKPD_WM3_SHIFT 24
+
+#define SNB_LATENCY(shift) (I915_READ(MCHBAR_MIRROR_BASE_SNB + SSKPD) >> (shift) & SSKPD_WM_MASK)
+#define SNB_READ_WM0_LATENCY() SNB_LATENCY(SSKPD_WM0_SHIFT)
+#define SNB_READ_WM1_LATENCY() SNB_LATENCY(SSKPD_WM1_SHIFT)
+#define SNB_READ_WM2_LATENCY() SNB_LATENCY(SSKPD_WM2_SHIFT)
+#define SNB_READ_WM3_LATENCY() SNB_LATENCY(SSKPD_WM3_SHIFT)
+
/*
* The two pipe frame counter registers are not synchronized, so
* reading a stable value is somewhat tricky. The following code
#define CURBBASE 0x700c4
#define CURBPOS 0x700c8
+#define CURCNTR(pipe) _PIPE(pipe, CURACNTR, CURBCNTR)
+#define CURBASE(pipe) _PIPE(pipe, CURABASE, CURBBASE)
+#define CURPOS(pipe) _PIPE(pipe, CURAPOS, CURBPOS)
+
/* Display A control */
#define DSPACNTR 0x70180
#define DISPLAY_PLANE_ENABLE (1<<31)
#define DSPASURF 0x7019C /* 965+ only */
#define DSPATILEOFF 0x701A4 /* 965+ only */
+#define DSPCNTR(plane) _PIPE(plane, DSPACNTR, DSPBCNTR)
+#define DSPADDR(plane) _PIPE(plane, DSPAADDR, DSPBADDR)
+#define DSPSTRIDE(plane) _PIPE(plane, DSPASTRIDE, DSPBSTRIDE)
+#define DSPPOS(plane) _PIPE(plane, DSPAPOS, DSPBPOS)
+#define DSPSIZE(plane) _PIPE(plane, DSPASIZE, DSPBSIZE)
+#define DSPSURF(plane) _PIPE(plane, DSPASURF, DSPBSURF)
+#define DSPTILEOFF(plane) _PIPE(plane, DSPATILEOFF, DSPBTILEOFF)
+
/* VBIOS flags */
#define SWF00 0x71410
#define SWF01 0x71414
#define RR_HW_HIGH_POWER_FRAMES_MASK 0xff00
#define FDI_PLL_BIOS_0 0x46000
+#define FDI_PLL_FB_CLOCK_MASK 0xff
#define FDI_PLL_BIOS_1 0x46004
#define FDI_PLL_BIOS_2 0x46008
#define DISPLAY_PORT_PLL_BIOS_0 0x4600c
#define DISPLAY_PORT_PLL_BIOS_2 0x46014
#define PCH_DSPCLK_GATE_D 0x42020
+# define DPFCUNIT_CLOCK_GATE_DISABLE (1 << 9)
+# define DPFCRUNIT_CLOCK_GATE_DISABLE (1 << 8)
# define DPFDUNIT_CLOCK_GATE_DISABLE (1 << 7)
# define DPARBUNIT_CLOCK_GATE_DISABLE (1 << 5)
# define MARIUNIT_CLOCK_GATE_DISABLE (1 << 18)
# define SVSMUNIT_CLOCK_GATE_DISABLE (1 << 1)
+#define PCH_3DCGDIS1 0x46024
+# define VFMUNIT_CLOCK_GATE_DISABLE (1 << 11)
+
#define FDI_PLL_FREQ_CTL 0x46030
#define FDI_PLL_FREQ_CHANGE_REQUEST (1<<24)
#define FDI_PLL_FREQ_LOCK_LIMIT_MASK 0xfff00
#define PIPEA_DATA_M1 0x60030
#define TU_SIZE(x) (((x)-1) << 25) /* default size 64 */
#define TU_SIZE_MASK 0x7e000000
-#define PIPEA_DATA_M1_OFFSET 0
+#define PIPE_DATA_M1_OFFSET 0
#define PIPEA_DATA_N1 0x60034
-#define PIPEA_DATA_N1_OFFSET 0
+#define PIPE_DATA_N1_OFFSET 0
#define PIPEA_DATA_M2 0x60038
-#define PIPEA_DATA_M2_OFFSET 0
+#define PIPE_DATA_M2_OFFSET 0
#define PIPEA_DATA_N2 0x6003c
-#define PIPEA_DATA_N2_OFFSET 0
+#define PIPE_DATA_N2_OFFSET 0
#define PIPEA_LINK_M1 0x60040
-#define PIPEA_LINK_M1_OFFSET 0
+#define PIPE_LINK_M1_OFFSET 0
#define PIPEA_LINK_N1 0x60044
-#define PIPEA_LINK_N1_OFFSET 0
+#define PIPE_LINK_N1_OFFSET 0
#define PIPEA_LINK_M2 0x60048
-#define PIPEA_LINK_M2_OFFSET 0
+#define PIPE_LINK_M2_OFFSET 0
#define PIPEA_LINK_N2 0x6004c
-#define PIPEA_LINK_N2_OFFSET 0
+#define PIPE_LINK_N2_OFFSET 0
/* PIPEB timing regs are same start from 0x61000 */
#define PIPEB_DATA_M1 0x61030
-#define PIPEB_DATA_M1_OFFSET 0
#define PIPEB_DATA_N1 0x61034
-#define PIPEB_DATA_N1_OFFSET 0
#define PIPEB_DATA_M2 0x61038
-#define PIPEB_DATA_M2_OFFSET 0
#define PIPEB_DATA_N2 0x6103c
-#define PIPEB_DATA_N2_OFFSET 0
#define PIPEB_LINK_M1 0x61040
-#define PIPEB_LINK_M1_OFFSET 0
#define PIPEB_LINK_N1 0x61044
-#define PIPEB_LINK_N1_OFFSET 0
#define PIPEB_LINK_M2 0x61048
-#define PIPEB_LINK_M2_OFFSET 0
#define PIPEB_LINK_N2 0x6104c
-#define PIPEB_LINK_N2_OFFSET 0
+
+#define PIPE_DATA_M1(pipe) _PIPE(pipe, PIPEA_DATA_M1, PIPEB_DATA_M1)
+#define PIPE_DATA_N1(pipe) _PIPE(pipe, PIPEA_DATA_N1, PIPEB_DATA_N1)
+#define PIPE_DATA_M2(pipe) _PIPE(pipe, PIPEA_DATA_M2, PIPEB_DATA_M2)
+#define PIPE_DATA_N2(pipe) _PIPE(pipe, PIPEA_DATA_N2, PIPEB_DATA_N2)
+#define PIPE_LINK_M1(pipe) _PIPE(pipe, PIPEA_LINK_M1, PIPEB_LINK_M1)
+#define PIPE_LINK_N1(pipe) _PIPE(pipe, PIPEA_LINK_N1, PIPEB_LINK_N1)
+#define PIPE_LINK_M2(pipe) _PIPE(pipe, PIPEA_LINK_M2, PIPEB_LINK_M2)
+#define PIPE_LINK_N2(pipe) _PIPE(pipe, PIPEA_LINK_N2, PIPEB_LINK_N2)
/* CPU panel fitter */
#define PFA_CTL_1 0x68080
#define DEIER 0x4400c
/* GT interrupt */
+#define GT_PIPE_NOTIFY (1 << 4)
#define GT_SYNC_STATUS (1 << 2)
#define GT_USER_INTERRUPT (1 << 0)
+#define GT_BSD_USER_INTERRUPT (1 << 5)
+#define GT_GEN6_BSD_USER_INTERRUPT (1 << 12)
+#define GT_BLT_USER_INTERRUPT (1 << 22)
#define GTISR 0x44010
#define GTIMR 0x44014
#define GTIIR 0x44018
#define GTIER 0x4401c
+#define ILK_DISPLAY_CHICKEN2 0x42004
+/* Required on all Ironlake and Sandybridge according to the B-Spec. */
+#define ILK_ELPIN_409_SELECT (1 << 25)
+#define ILK_DPARB_GATE (1<<22)
+#define ILK_VSDPFD_FULL (1<<21)
+#define ILK_DISPLAY_CHICKEN_FUSES 0x42014
+#define ILK_INTERNAL_GRAPHICS_DISABLE (1<<31)
+#define ILK_INTERNAL_DISPLAY_DISABLE (1<<30)
+#define ILK_DISPLAY_DEBUG_DISABLE (1<<29)
+#define ILK_HDCP_DISABLE (1<<25)
+#define ILK_eDP_A_DISABLE (1<<24)
+#define ILK_DESKTOP (1<<23)
+#define ILK_DSPCLK_GATE 0x42020
+#define ILK_DPARB_CLK_GATE (1<<5)
+#define ILK_DPFD_CLK_GATE (1<<7)
+
+/* According to spec this bit 7/8/9 of 0x42020 should be set to enable FBC */
+#define ILK_CLK_FBC (1<<7)
+#define ILK_DPFC_DIS1 (1<<8)
+#define ILK_DPFC_DIS2 (1<<9)
+
#define DISP_ARB_CTL 0x45000
#define DISP_TILE_SURFACE_SWIZZLING (1<<13)
+#define DISP_FBC_WM_DIS (1<<15)
/* PCH */
/* south display engine interrupt */
+#define SDE_AUDIO_POWER_D (1 << 27)
+#define SDE_AUDIO_POWER_C (1 << 26)
+#define SDE_AUDIO_POWER_B (1 << 25)
+#define SDE_AUDIO_POWER_SHIFT (25)
+#define SDE_AUDIO_POWER_MASK (7 << SDE_AUDIO_POWER_SHIFT)
+#define SDE_GMBUS (1 << 24)
+#define SDE_AUDIO_HDCP_TRANSB (1 << 23)
+#define SDE_AUDIO_HDCP_TRANSA (1 << 22)
+#define SDE_AUDIO_HDCP_MASK (3 << 22)
+#define SDE_AUDIO_TRANSB (1 << 21)
+#define SDE_AUDIO_TRANSA (1 << 20)
+#define SDE_AUDIO_TRANS_MASK (3 << 20)
+#define SDE_POISON (1 << 19)
+/* 18 reserved */
+#define SDE_FDI_RXB (1 << 17)
+#define SDE_FDI_RXA (1 << 16)
+#define SDE_FDI_MASK (3 << 16)
+#define SDE_AUXD (1 << 15)
+#define SDE_AUXC (1 << 14)
+#define SDE_AUXB (1 << 13)
+#define SDE_AUX_MASK (7 << 13)
+/* 12 reserved */
#define SDE_CRT_HOTPLUG (1 << 11)
#define SDE_PORTD_HOTPLUG (1 << 10)
#define SDE_PORTC_HOTPLUG (1 << 9)
#define SDE_PORTB_HOTPLUG (1 << 8)
#define SDE_SDVOB_HOTPLUG (1 << 6)
#define SDE_HOTPLUG_MASK (0xf << 8)
+#define SDE_TRANSB_CRC_DONE (1 << 5)
+#define SDE_TRANSB_CRC_ERR (1 << 4)
+#define SDE_TRANSB_FIFO_UNDER (1 << 3)
+#define SDE_TRANSA_CRC_DONE (1 << 2)
+#define SDE_TRANSA_CRC_ERR (1 << 1)
+#define SDE_TRANSA_FIFO_UNDER (1 << 0)
+#define SDE_TRANS_MASK (0x3f)
+/* CPT */
+#define SDE_CRT_HOTPLUG_CPT (1 << 19)
+#define SDE_PORTD_HOTPLUG_CPT (1 << 23)
+#define SDE_PORTC_HOTPLUG_CPT (1 << 22)
+#define SDE_PORTB_HOTPLUG_CPT (1 << 21)
+#define SDE_HOTPLUG_MASK_CPT (SDE_CRT_HOTPLUG_CPT | \
+ SDE_PORTD_HOTPLUG_CPT | \
+ SDE_PORTC_HOTPLUG_CPT | \
+ SDE_PORTB_HOTPLUG_CPT)
#define SDEISR 0xc4000
#define SDEIMR 0xc4004
#define PCH_DPLL_A 0xc6014
#define PCH_DPLL_B 0xc6018
+#define PCH_DPLL(pipe) _PIPE(pipe, PCH_DPLL_A, PCH_DPLL_B)
#define PCH_FPA0 0xc6040
+#define FP_CB_TUNE (0x3<<22)
#define PCH_FPA1 0xc6044
#define PCH_FPB0 0xc6048
#define PCH_FPB1 0xc604c
+#define PCH_FP0(pipe) _PIPE(pipe, PCH_FPA0, PCH_FPB0)
+#define PCH_FP1(pipe) _PIPE(pipe, PCH_FPA1, PCH_FPB1)
#define PCH_DPLL_TEST 0xc606c
#define PCH_SSC4_PARMS 0xc6210
#define PCH_SSC4_AUX_PARMS 0xc6214
+#define PCH_DPLL_SEL 0xc7000
+#define TRANSA_DPLL_ENABLE (1<<3)
+#define TRANSA_DPLLB_SEL (1<<0)
+#define TRANSA_DPLLA_SEL 0
+#define TRANSB_DPLL_ENABLE (1<<7)
+#define TRANSB_DPLLB_SEL (1<<4)
+#define TRANSB_DPLLA_SEL (0)
+#define TRANSC_DPLL_ENABLE (1<<11)
+#define TRANSC_DPLLB_SEL (1<<8)
+#define TRANSC_DPLLA_SEL (0)
+
/* transcoder */
#define TRANS_HTOTAL_A 0xe0000
#define TRANS_VBLANK_B 0xe1010
#define TRANS_VSYNC_B 0xe1014
+#define TRANS_HTOTAL(pipe) _PIPE(pipe, TRANS_HTOTAL_A, TRANS_HTOTAL_B)
+#define TRANS_HBLANK(pipe) _PIPE(pipe, TRANS_HBLANK_A, TRANS_HBLANK_B)
+#define TRANS_HSYNC(pipe) _PIPE(pipe, TRANS_HSYNC_A, TRANS_HSYNC_B)
+#define TRANS_VTOTAL(pipe) _PIPE(pipe, TRANS_VTOTAL_A, TRANS_VTOTAL_B)
+#define TRANS_VBLANK(pipe) _PIPE(pipe, TRANS_VBLANK_A, TRANS_VBLANK_B)
+#define TRANS_VSYNC(pipe) _PIPE(pipe, TRANS_VSYNC_A, TRANS_VSYNC_B)
+
#define TRANSB_DATA_M1 0xe1030
#define TRANSB_DATA_N1 0xe1034
#define TRANSB_DATA_M2 0xe1038
#define TRANSACONF 0xf0008
#define TRANSBCONF 0xf1008
+#define TRANSCONF(plane) _PIPE(plane, TRANSACONF, TRANSBCONF)
#define TRANS_DISABLE (0<<31)
#define TRANS_ENABLE (1<<31)
#define TRANS_STATE_MASK (1<<30)
#define FDI_RXA_CHICKEN 0xc200c
#define FDI_RXB_CHICKEN 0xc2010
#define FDI_RX_PHASE_SYNC_POINTER_ENABLE (1)
+#define FDI_RX_CHICKEN(pipe) _PIPE(pipe, FDI_RXA_CHICKEN, FDI_RXB_CHICKEN)
+
+#define SOUTH_DSPCLK_GATE_D 0xc2020
+#define PCH_DPLSUNIT_CLOCK_GATE_DISABLE (1<<29)
/* CPU: FDI_TX */
#define FDI_TXA_CTL 0x60100
#define FDI_TXB_CTL 0x61100
+#define FDI_TX_CTL(pipe) _PIPE(pipe, FDI_TXA_CTL, FDI_TXB_CTL)
#define FDI_TX_DISABLE (0<<31)
#define FDI_TX_ENABLE (1<<31)
#define FDI_LINK_TRAIN_PATTERN_1 (0<<28)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_1_5X (1<<22)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_2X (2<<22)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_3X (3<<22)
+/* ILK always use 400mV 0dB for voltage swing and pre-emphasis level.
+ SNB has different settings. */
+/* SNB A-stepping */
+#define FDI_LINK_TRAIN_400MV_0DB_SNB_A (0x38<<22)
+#define FDI_LINK_TRAIN_400MV_6DB_SNB_A (0x02<<22)
+#define FDI_LINK_TRAIN_600MV_3_5DB_SNB_A (0x01<<22)
+#define FDI_LINK_TRAIN_800MV_0DB_SNB_A (0x0<<22)
+/* SNB B-stepping */
+#define FDI_LINK_TRAIN_400MV_0DB_SNB_B (0x0<<22)
+#define FDI_LINK_TRAIN_400MV_6DB_SNB_B (0x3a<<22)
+#define FDI_LINK_TRAIN_600MV_3_5DB_SNB_B (0x39<<22)
+#define FDI_LINK_TRAIN_800MV_0DB_SNB_B (0x38<<22)
+#define FDI_LINK_TRAIN_VOL_EMP_MASK (0x3f<<22)
#define FDI_DP_PORT_WIDTH_X1 (0<<19)
#define FDI_DP_PORT_WIDTH_X2 (1<<19)
#define FDI_DP_PORT_WIDTH_X3 (2<<19)
/* FDI_RX, FDI_X is hard-wired to Transcoder_X */
#define FDI_RXA_CTL 0xf000c
#define FDI_RXB_CTL 0xf100c
+#define FDI_RX_CTL(pipe) _PIPE(pipe, FDI_RXA_CTL, FDI_RXB_CTL)
#define FDI_RX_ENABLE (1<<31)
-#define FDI_RX_DISABLE (0<<31)
/* train, dp width same as FDI_TX */
#define FDI_DP_PORT_WIDTH_X8 (7<<19)
#define FDI_8BPC (0<<16)
#define FDI_FS_ERR_REPORT_ENABLE (1<<9)
#define FDI_FE_ERR_REPORT_ENABLE (1<<8)
#define FDI_RX_ENHANCE_FRAME_ENABLE (1<<6)
-#define FDI_SEL_RAWCLK (0<<4)
-#define FDI_SEL_PCDCLK (1<<4)
+#define FDI_PCDCLK (1<<4)
+/* CPT */
+#define FDI_AUTO_TRAINING (1<<10)
+#define FDI_LINK_TRAIN_PATTERN_1_CPT (0<<8)
+#define FDI_LINK_TRAIN_PATTERN_2_CPT (1<<8)
+#define FDI_LINK_TRAIN_PATTERN_IDLE_CPT (2<<8)
+#define FDI_LINK_TRAIN_NORMAL_CPT (3<<8)
+#define FDI_LINK_TRAIN_PATTERN_MASK_CPT (3<<8)
#define FDI_RXA_MISC 0xf0010
#define FDI_RXB_MISC 0xf1010
#define FDI_RXA_TUSIZE2 0xf0038
#define FDI_RXB_TUSIZE1 0xf1030
#define FDI_RXB_TUSIZE2 0xf1038
+#define FDI_RX_MISC(pipe) _PIPE(pipe, FDI_RXA_MISC, FDI_RXB_MISC)
+#define FDI_RX_TUSIZE1(pipe) _PIPE(pipe, FDI_RXA_TUSIZE1, FDI_RXB_TUSIZE1)
+#define FDI_RX_TUSIZE2(pipe) _PIPE(pipe, FDI_RXA_TUSIZE2, FDI_RXB_TUSIZE2)
/* FDI_RX interrupt register format */
#define FDI_RX_INTER_LANE_ALIGN (1<<10)
#define FDI_RXA_IMR 0xf0018
#define FDI_RXB_IIR 0xf1014
#define FDI_RXB_IMR 0xf1018
+#define FDI_RX_IIR(pipe) _PIPE(pipe, FDI_RXA_IIR, FDI_RXB_IIR)
+#define FDI_RX_IMR(pipe) _PIPE(pipe, FDI_RXA_IMR, FDI_RXB_IMR)
#define FDI_PLL_CTL_1 0xfe000
#define FDI_PLL_CTL_2 0xfe004
#define SDVO_ENCODING (0)
#define TMDS_ENCODING (2 << 10)
#define NULL_PACKET_VSYNC_ENABLE (1 << 9)
+/* CPT */
+#define HDMI_MODE_SELECT (1 << 9)
+#define DVI_MODE_SELECT (0)
#define SDVOB_BORDER_ENABLE (1 << 7)
#define AUDIO_ENABLE (1 << 6)
#define VSYNC_ACTIVE_HIGH (1 << 4)
#define HSYNC_ACTIVE_HIGH (1 << 3)
#define PORT_DETECTED (1 << 2)
+/* PCH SDVOB multiplex with HDMIB */
+#define PCH_SDVOB HDMIB
+
#define HDMIC 0xe1150
#define HDMID 0xe1160
#define PCH_PP_STATUS 0xc7200
#define PCH_PP_CONTROL 0xc7204
+#define PANEL_UNLOCK_REGS (0xabcd << 16)
#define EDP_FORCE_VDD (1 << 3)
#define EDP_BLC_ENABLE (1 << 2)
#define PANEL_POWER_RESET (1 << 1)
#define PCH_DPD_AUX_CH_DATA4 0xe4320
#define PCH_DPD_AUX_CH_DATA5 0xe4324
+/* CPT */
+#define PORT_TRANS_A_SEL_CPT 0
+#define PORT_TRANS_B_SEL_CPT (1<<29)
+#define PORT_TRANS_C_SEL_CPT (2<<29)
+#define PORT_TRANS_SEL_MASK (3<<29)
+
+#define TRANS_DP_CTL_A 0xe0300
+#define TRANS_DP_CTL_B 0xe1300
+#define TRANS_DP_CTL_C 0xe2300
+#define TRANS_DP_CTL(pipe) (TRANS_DP_CTL_A + (pipe) * 0x01000)
+#define TRANS_DP_OUTPUT_ENABLE (1<<31)
+#define TRANS_DP_PORT_SEL_B (0<<29)
+#define TRANS_DP_PORT_SEL_C (1<<29)
+#define TRANS_DP_PORT_SEL_D (2<<29)
+#define TRANS_DP_PORT_SEL_MASK (3<<29)
+#define TRANS_DP_AUDIO_ONLY (1<<26)
+#define TRANS_DP_ENH_FRAMING (1<<18)
+#define TRANS_DP_8BPC (0<<9)
+#define TRANS_DP_10BPC (1<<9)
+#define TRANS_DP_6BPC (2<<9)
+#define TRANS_DP_12BPC (3<<9)
+#define TRANS_DP_BPC_MASK (3<<9)
+#define TRANS_DP_VSYNC_ACTIVE_HIGH (1<<4)
+#define TRANS_DP_VSYNC_ACTIVE_LOW 0
+#define TRANS_DP_HSYNC_ACTIVE_HIGH (1<<3)
+#define TRANS_DP_HSYNC_ACTIVE_LOW 0
+#define TRANS_DP_SYNC_MASK (3<<3)
+
+/* SNB eDP training params */
+/* SNB A-stepping */
+#define EDP_LINK_TRAIN_400MV_0DB_SNB_A (0x38<<22)
+#define EDP_LINK_TRAIN_400MV_6DB_SNB_A (0x02<<22)
+#define EDP_LINK_TRAIN_600MV_3_5DB_SNB_A (0x01<<22)
+#define EDP_LINK_TRAIN_800MV_0DB_SNB_A (0x0<<22)
+/* SNB B-stepping */
+#define EDP_LINK_TRAIN_400_600MV_0DB_SNB_B (0x0<<22)
+#define EDP_LINK_TRAIN_400MV_3_5DB_SNB_B (0x1<<22)
+#define EDP_LINK_TRAIN_400_600MV_6DB_SNB_B (0x3a<<22)
+#define EDP_LINK_TRAIN_600_800MV_3_5DB_SNB_B (0x39<<22)
+#define EDP_LINK_TRAIN_800_1200MV_0DB_SNB_B (0x38<<22)
+#define EDP_LINK_TRAIN_VOL_EMP_MASK_SNB (0x3f<<22)
+
+#define FORCEWAKE 0xA18C
+#define FORCEWAKE_ACK 0x130090
+
+#define GT_FIFO_FREE_ENTRIES 0x120008
+
+#define GEN6_RPNSWREQ 0xA008
+#define GEN6_TURBO_DISABLE (1<<31)
+#define GEN6_FREQUENCY(x) ((x)<<25)
+#define GEN6_OFFSET(x) ((x)<<19)
+#define GEN6_AGGRESSIVE_TURBO (0<<15)
+#define GEN6_RC_VIDEO_FREQ 0xA00C
+#define GEN6_RC_CONTROL 0xA090
+#define GEN6_RC_CTL_RC6pp_ENABLE (1<<16)
+#define GEN6_RC_CTL_RC6p_ENABLE (1<<17)
+#define GEN6_RC_CTL_RC6_ENABLE (1<<18)
+#define GEN6_RC_CTL_RC1e_ENABLE (1<<20)
+#define GEN6_RC_CTL_RC7_ENABLE (1<<22)
+#define GEN6_RC_CTL_EI_MODE(x) ((x)<<27)
+#define GEN6_RC_CTL_HW_ENABLE (1<<31)
+#define GEN6_RP_DOWN_TIMEOUT 0xA010
+#define GEN6_RP_INTERRUPT_LIMITS 0xA014
+#define GEN6_RPSTAT1 0xA01C
+#define GEN6_RP_CONTROL 0xA024
+#define GEN6_RP_MEDIA_TURBO (1<<11)
+#define GEN6_RP_USE_NORMAL_FREQ (1<<9)
+#define GEN6_RP_MEDIA_IS_GFX (1<<8)
+#define GEN6_RP_ENABLE (1<<7)
+#define GEN6_RP_UP_BUSY_MAX (0x2<<3)
+#define GEN6_RP_DOWN_BUSY_MIN (0x2<<0)
+#define GEN6_RP_UP_THRESHOLD 0xA02C
+#define GEN6_RP_DOWN_THRESHOLD 0xA030
+#define GEN6_RP_UP_EI 0xA068
+#define GEN6_RP_DOWN_EI 0xA06C
+#define GEN6_RP_IDLE_HYSTERSIS 0xA070
+#define GEN6_RC_STATE 0xA094
+#define GEN6_RC1_WAKE_RATE_LIMIT 0xA098
+#define GEN6_RC6_WAKE_RATE_LIMIT 0xA09C
+#define GEN6_RC6pp_WAKE_RATE_LIMIT 0xA0A0
+#define GEN6_RC_EVALUATION_INTERVAL 0xA0A8
+#define GEN6_RC_IDLE_HYSTERSIS 0xA0AC
+#define GEN6_RC_SLEEP 0xA0B0
+#define GEN6_RC1e_THRESHOLD 0xA0B4
+#define GEN6_RC6_THRESHOLD 0xA0B8
+#define GEN6_RC6p_THRESHOLD 0xA0BC
+#define GEN6_RC6pp_THRESHOLD 0xA0C0
+#define GEN6_PMINTRMSK 0xA168
+
+#define GEN6_PMISR 0x44020
+#define GEN6_PMIMR 0x44024
+#define GEN6_PMIIR 0x44028
+#define GEN6_PMIER 0x4402C
+#define GEN6_PM_MBOX_EVENT (1<<25)
+#define GEN6_PM_THERMAL_EVENT (1<<24)
+#define GEN6_PM_RP_DOWN_TIMEOUT (1<<6)
+#define GEN6_PM_RP_UP_THRESHOLD (1<<5)
+#define GEN6_PM_RP_DOWN_THRESHOLD (1<<4)
+#define GEN6_PM_RP_UP_EI_EXPIRED (1<<2)
+#define GEN6_PM_RP_DOWN_EI_EXPIRED (1<<1)
+
+#define GEN6_PCODE_MAILBOX 0x138124
+#define GEN6_PCODE_READY (1<<31)
+#define GEN6_READ_OC_PARAMS 0xc
+#define GEN6_PCODE_WRITE_MIN_FREQ_TABLE 0x9
+#define GEN6_PCODE_DATA 0x138128
+
#endif /* _I915_REG_H_ */
projects / linux-flexiantxendom0-natty.git / blobdiff