/*
- * Copyright (c) 2003-2007 Chelsio, Inc. All rights reserved.
+ * Copyright (c) 2003-2008 Chelsio, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
#include "sge_defs.h"
#include "firmware_exports.h"
+static void t3_port_intr_clear(struct adapter *adapter, int idx);
+
/**
* t3_wait_op_done_val - wait until an operation is completed
* @adapter: the adapter performing the operation
return 0;
}
if (--attempts == 0)
- return -EAGAIN;
+ return -EAGAIN;
if (delay)
udelay(delay);
}
static void mi1_init(struct adapter *adap, const struct adapter_info *ai)
{
u32 clkdiv = adap->params.vpd.cclk / (2 * adap->params.vpd.mdc) - 1;
- u32 val = F_PREEN | V_MDIINV(ai->mdiinv) | V_MDIEN(ai->mdien) |
- V_CLKDIV(clkdiv);
+ u32 val = F_PREEN | V_CLKDIV(clkdiv);
- if (!(ai->caps & SUPPORTED_10000baseT_Full))
- val |= V_ST(1);
t3_write_reg(adap, A_MI1_CFG, val);
}
-#define MDIO_ATTEMPTS 10
+#define MDIO_ATTEMPTS 20
/*
- * MI1 read/write operations for direct-addressed PHYs.
+ * MI1 read/write operations for clause 22 PHYs.
*/
-static int mi1_read(struct adapter *adapter, int phy_addr, int mmd_addr,
- int reg_addr, unsigned int *valp)
+static int t3_mi1_read(struct net_device *dev, int phy_addr, int mmd_addr,
+ u16 reg_addr)
{
+ struct port_info *pi = netdev_priv(dev);
+ struct adapter *adapter = pi->adapter;
int ret;
u32 addr = V_REGADDR(reg_addr) | V_PHYADDR(phy_addr);
- if (mmd_addr)
- return -EINVAL;
-
mutex_lock(&adapter->mdio_lock);
+ t3_set_reg_field(adapter, A_MI1_CFG, V_ST(M_ST), V_ST(1));
t3_write_reg(adapter, A_MI1_ADDR, addr);
t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(2));
- ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 10);
if (!ret)
- *valp = t3_read_reg(adapter, A_MI1_DATA);
+ ret = t3_read_reg(adapter, A_MI1_DATA);
mutex_unlock(&adapter->mdio_lock);
return ret;
}
-static int mi1_write(struct adapter *adapter, int phy_addr, int mmd_addr,
- int reg_addr, unsigned int val)
+static int t3_mi1_write(struct net_device *dev, int phy_addr, int mmd_addr,
+ u16 reg_addr, u16 val)
{
+ struct port_info *pi = netdev_priv(dev);
+ struct adapter *adapter = pi->adapter;
int ret;
u32 addr = V_REGADDR(reg_addr) | V_PHYADDR(phy_addr);
- if (mmd_addr)
- return -EINVAL;
-
mutex_lock(&adapter->mdio_lock);
+ t3_set_reg_field(adapter, A_MI1_CFG, V_ST(M_ST), V_ST(1));
t3_write_reg(adapter, A_MI1_ADDR, addr);
t3_write_reg(adapter, A_MI1_DATA, val);
t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(1));
- ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 10);
mutex_unlock(&adapter->mdio_lock);
return ret;
}
static const struct mdio_ops mi1_mdio_ops = {
- mi1_read,
- mi1_write
+ .read = t3_mi1_read,
+ .write = t3_mi1_write,
+ .mode_support = MDIO_SUPPORTS_C22
};
/*
- * MI1 read/write operations for indirect-addressed PHYs.
+ * Performs the address cycle for clause 45 PHYs.
+ * Must be called with the MDIO_LOCK held.
*/
-static int mi1_ext_read(struct adapter *adapter, int phy_addr, int mmd_addr,
- int reg_addr, unsigned int *valp)
+static int mi1_wr_addr(struct adapter *adapter, int phy_addr, int mmd_addr,
+ int reg_addr)
{
- int ret;
u32 addr = V_REGADDR(mmd_addr) | V_PHYADDR(phy_addr);
- mutex_lock(&adapter->mdio_lock);
+ t3_set_reg_field(adapter, A_MI1_CFG, V_ST(M_ST), 0);
t3_write_reg(adapter, A_MI1_ADDR, addr);
t3_write_reg(adapter, A_MI1_DATA, reg_addr);
t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(0));
- ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ return t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0,
+ MDIO_ATTEMPTS, 10);
+}
+
+/*
+ * MI1 read/write operations for indirect-addressed PHYs.
+ */
+static int mi1_ext_read(struct net_device *dev, int phy_addr, int mmd_addr,
+ u16 reg_addr)
+{
+ struct port_info *pi = netdev_priv(dev);
+ struct adapter *adapter = pi->adapter;
+ int ret;
+
+ mutex_lock(&adapter->mdio_lock);
+ ret = mi1_wr_addr(adapter, phy_addr, mmd_addr, reg_addr);
if (!ret) {
t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(3));
ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0,
- MDIO_ATTEMPTS, 20);
+ MDIO_ATTEMPTS, 10);
if (!ret)
- *valp = t3_read_reg(adapter, A_MI1_DATA);
+ ret = t3_read_reg(adapter, A_MI1_DATA);
}
mutex_unlock(&adapter->mdio_lock);
return ret;
}
-static int mi1_ext_write(struct adapter *adapter, int phy_addr, int mmd_addr,
- int reg_addr, unsigned int val)
+static int mi1_ext_write(struct net_device *dev, int phy_addr, int mmd_addr,
+ u16 reg_addr, u16 val)
{
+ struct port_info *pi = netdev_priv(dev);
+ struct adapter *adapter = pi->adapter;
int ret;
- u32 addr = V_REGADDR(mmd_addr) | V_PHYADDR(phy_addr);
mutex_lock(&adapter->mdio_lock);
- t3_write_reg(adapter, A_MI1_ADDR, addr);
- t3_write_reg(adapter, A_MI1_DATA, reg_addr);
- t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(0));
- ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ ret = mi1_wr_addr(adapter, phy_addr, mmd_addr, reg_addr);
if (!ret) {
t3_write_reg(adapter, A_MI1_DATA, val);
t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(1));
ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0,
- MDIO_ATTEMPTS, 20);
+ MDIO_ATTEMPTS, 10);
}
mutex_unlock(&adapter->mdio_lock);
return ret;
}
static const struct mdio_ops mi1_mdio_ext_ops = {
- mi1_ext_read,
- mi1_ext_write
+ .read = mi1_ext_read,
+ .write = mi1_ext_write,
+ .mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22
};
/**
int ret;
unsigned int val;
- ret = mdio_read(phy, mmd, reg, &val);
+ ret = t3_mdio_read(phy, mmd, reg, &val);
if (!ret) {
val &= ~clear;
- ret = mdio_write(phy, mmd, reg, val | set);
+ ret = t3_mdio_write(phy, mmd, reg, val | set);
}
return ret;
}
int err;
unsigned int ctl;
- err = t3_mdio_change_bits(phy, mmd, MII_BMCR, BMCR_PDOWN, BMCR_RESET);
+ err = t3_mdio_change_bits(phy, mmd, MDIO_CTRL1, MDIO_CTRL1_LPOWER,
+ MDIO_CTRL1_RESET);
if (err || !wait)
return err;
do {
- err = mdio_read(phy, mmd, MII_BMCR, &ctl);
+ err = t3_mdio_read(phy, mmd, MDIO_CTRL1, &ctl);
if (err)
return err;
- ctl &= BMCR_RESET;
+ ctl &= MDIO_CTRL1_RESET;
if (ctl)
msleep(1);
} while (ctl && --wait);
int err;
unsigned int val = 0;
- err = mdio_read(phy, 0, MII_CTRL1000, &val);
+ err = t3_mdio_read(phy, MDIO_DEVAD_NONE, MII_CTRL1000, &val);
if (err)
return err;
if (advert & ADVERTISED_1000baseT_Full)
val |= ADVERTISE_1000FULL;
- err = mdio_write(phy, 0, MII_CTRL1000, val);
+ err = t3_mdio_write(phy, MDIO_DEVAD_NONE, MII_CTRL1000, val);
if (err)
return err;
val |= ADVERTISE_PAUSE_CAP;
if (advert & ADVERTISED_Asym_Pause)
val |= ADVERTISE_PAUSE_ASYM;
- return mdio_write(phy, 0, MII_ADVERTISE, val);
+ return t3_mdio_write(phy, MDIO_DEVAD_NONE, MII_ADVERTISE, val);
+}
+
+/**
+ * t3_phy_advertise_fiber - set fiber PHY advertisement register
+ * @phy: the PHY to operate on
+ * @advert: bitmap of capabilities the PHY should advertise
+ *
+ * Sets a fiber PHY's advertisement register to advertise the
+ * requested capabilities.
+ */
+int t3_phy_advertise_fiber(struct cphy *phy, unsigned int advert)
+{
+ unsigned int val = 0;
+
+ if (advert & ADVERTISED_1000baseT_Half)
+ val |= ADVERTISE_1000XHALF;
+ if (advert & ADVERTISED_1000baseT_Full)
+ val |= ADVERTISE_1000XFULL;
+ if (advert & ADVERTISED_Pause)
+ val |= ADVERTISE_1000XPAUSE;
+ if (advert & ADVERTISED_Asym_Pause)
+ val |= ADVERTISE_1000XPSE_ASYM;
+ return t3_mdio_write(phy, MDIO_DEVAD_NONE, MII_ADVERTISE, val);
}
/**
int err;
unsigned int ctl;
- err = mdio_read(phy, 0, MII_BMCR, &ctl);
+ err = t3_mdio_read(phy, MDIO_DEVAD_NONE, MII_BMCR, &ctl);
if (err)
return err;
}
if (ctl & BMCR_SPEED1000) /* auto-negotiation required for GigE */
ctl |= BMCR_ANENABLE;
- return mdio_write(phy, 0, MII_BMCR, ctl);
+ return t3_mdio_write(phy, MDIO_DEVAD_NONE, MII_BMCR, ctl);
+}
+
+int t3_phy_lasi_intr_enable(struct cphy *phy)
+{
+ return t3_mdio_write(phy, MDIO_MMD_PMAPMD, MDIO_PMA_LASI_CTRL,
+ MDIO_PMA_LASI_LSALARM);
+}
+
+int t3_phy_lasi_intr_disable(struct cphy *phy)
+{
+ return t3_mdio_write(phy, MDIO_MMD_PMAPMD, MDIO_PMA_LASI_CTRL, 0);
+}
+
+int t3_phy_lasi_intr_clear(struct cphy *phy)
+{
+ u32 val;
+
+ return t3_mdio_read(phy, MDIO_MMD_PMAPMD, MDIO_PMA_LASI_STAT, &val);
+}
+
+int t3_phy_lasi_intr_handler(struct cphy *phy)
+{
+ unsigned int status;
+ int err = t3_mdio_read(phy, MDIO_MMD_PMAPMD, MDIO_PMA_LASI_STAT,
+ &status);
+
+ if (err)
+ return err;
+ return (status & MDIO_PMA_LASI_LSALARM) ? cphy_cause_link_change : 0;
}
static const struct adapter_info t3_adap_info[] = {
- {2, 0, 0, 0,
+ {1, 1, 0,
F_GPIO2_OEN | F_GPIO4_OEN |
- F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, F_GPIO3 | F_GPIO5,
- 0,
+ F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, { S_GPIO3, S_GPIO5 }, 0,
&mi1_mdio_ops, "Chelsio PE9000"},
- {2, 0, 0, 0,
+ {1, 1, 0,
F_GPIO2_OEN | F_GPIO4_OEN |
- F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, F_GPIO3 | F_GPIO5,
- 0,
+ F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, { S_GPIO3, S_GPIO5 }, 0,
&mi1_mdio_ops, "Chelsio T302"},
- {1, 0, 0, 0,
+ {1, 0, 0,
F_GPIO1_OEN | F_GPIO6_OEN | F_GPIO7_OEN | F_GPIO10_OEN |
- F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL, 0,
- SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
+ F_GPIO11_OEN | F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL,
+ { 0 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
&mi1_mdio_ext_ops, "Chelsio T310"},
- {2, 0, 0, 0,
+ {1, 1, 0,
F_GPIO1_OEN | F_GPIO2_OEN | F_GPIO4_OEN | F_GPIO5_OEN | F_GPIO6_OEN |
F_GPIO7_OEN | F_GPIO10_OEN | F_GPIO11_OEN | F_GPIO1_OUT_VAL |
- F_GPIO5_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL, 0,
- SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
+ F_GPIO5_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL,
+ { S_GPIO9, S_GPIO3 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
&mi1_mdio_ext_ops, "Chelsio T320"},
+ {},
+ {},
+ {1, 0, 0,
+ F_GPIO1_OEN | F_GPIO2_OEN | F_GPIO4_OEN | F_GPIO6_OEN | F_GPIO7_OEN |
+ F_GPIO10_OEN | F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL,
+ { S_GPIO9 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
+ &mi1_mdio_ext_ops, "Chelsio T310" },
+ {1, 0, 0,
+ F_GPIO1_OEN | F_GPIO6_OEN | F_GPIO7_OEN |
+ F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL,
+ { S_GPIO9 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
+ &mi1_mdio_ext_ops, "Chelsio N320E-G2" },
};
/*
return id < ARRAY_SIZE(t3_adap_info) ? &t3_adap_info[id] : NULL;
}
-#define CAPS_1G (SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Full | \
- SUPPORTED_1000baseT_Full | SUPPORTED_Autoneg | SUPPORTED_MII)
-#define CAPS_10G (SUPPORTED_10000baseT_Full | SUPPORTED_AUI)
+struct port_type_info {
+ int (*phy_prep)(struct cphy *phy, struct adapter *adapter,
+ int phy_addr, const struct mdio_ops *ops);
+};
static const struct port_type_info port_types[] = {
- {NULL},
- {t3_ael1002_phy_prep, CAPS_10G | SUPPORTED_FIBRE,
- "10GBASE-XR"},
- {t3_vsc8211_phy_prep, CAPS_1G | SUPPORTED_TP | SUPPORTED_IRQ,
- "10/100/1000BASE-T"},
- {NULL, CAPS_1G | SUPPORTED_TP | SUPPORTED_IRQ,
- "10/100/1000BASE-T"},
- {t3_xaui_direct_phy_prep, CAPS_10G | SUPPORTED_TP, "10GBASE-CX4"},
- {NULL, CAPS_10G, "10GBASE-KX4"},
- {t3_qt2045_phy_prep, CAPS_10G | SUPPORTED_TP, "10GBASE-CX4"},
- {t3_ael1006_phy_prep, CAPS_10G | SUPPORTED_FIBRE,
- "10GBASE-SR"},
- {NULL, CAPS_10G | SUPPORTED_TP, "10GBASE-CX4"},
+ { NULL },
+ { t3_ael1002_phy_prep },
+ { t3_vsc8211_phy_prep },
+ { NULL},
+ { t3_xaui_direct_phy_prep },
+ { t3_ael2005_phy_prep },
+ { t3_qt2045_phy_prep },
+ { t3_ael1006_phy_prep },
+ { NULL },
+ { t3_aq100x_phy_prep },
+ { t3_ael2020_phy_prep },
};
-#undef CAPS_1G
-#undef CAPS_10G
-
#define VPD_ENTRY(name, len) \
u8 name##_kword[2]; u8 name##_len; u8 name##_data[len]
u32 pad; /* for multiple-of-4 sizing and alignment */
};
-#define EEPROM_MAX_POLL 4
+#define EEPROM_MAX_POLL 40
#define EEPROM_STAT_ADDR 0x4000
#define VPD_BASE 0xc00
*
* Read a 32-bit word from a location in VPD EEPROM using the card's PCI
* VPD ROM capability. A zero is written to the flag bit when the
- * addres is written to the control register. The hardware device will
+ * address is written to the control register. The hardware device will
* set the flag to 1 when 4 bytes have been read into the data register.
*/
-int t3_seeprom_read(struct adapter *adapter, u32 addr, u32 *data)
+int t3_seeprom_read(struct adapter *adapter, u32 addr, __le32 *data)
{
u16 val;
int attempts = EEPROM_MAX_POLL;
+ u32 v;
unsigned int base = adapter->params.pci.vpd_cap_addr;
if ((addr >= EEPROMSIZE && addr != EEPROM_STAT_ADDR) || (addr & 3))
CH_ERR(adapter, "reading EEPROM address 0x%x failed\n", addr);
return -EIO;
}
- pci_read_config_dword(adapter->pdev, base + PCI_VPD_DATA, data);
- *data = le32_to_cpu(*data);
+ pci_read_config_dword(adapter->pdev, base + PCI_VPD_DATA, &v);
+ *data = cpu_to_le32(v);
return 0;
}
* Write a 32-bit word to a location in VPD EEPROM using the card's PCI
* VPD ROM capability.
*/
-int t3_seeprom_write(struct adapter *adapter, u32 addr, u32 data)
+int t3_seeprom_write(struct adapter *adapter, u32 addr, __le32 data)
{
u16 val;
int attempts = EEPROM_MAX_POLL;
return -EINVAL;
pci_write_config_dword(adapter->pdev, base + PCI_VPD_DATA,
- cpu_to_le32(data));
+ le32_to_cpu(data));
pci_write_config_word(adapter->pdev,base + PCI_VPD_ADDR,
addr | PCI_VPD_ADDR_F);
do {
return t3_seeprom_write(adapter, EEPROM_STAT_ADDR, enable ? 0xc : 0);
}
-/*
- * Convert a character holding a hex digit to a number.
- */
-static unsigned int hex2int(unsigned char c)
-{
- return isdigit(c) ? c - '0' : toupper(c) - 'A' + 10;
-}
-
/**
* get_vpd_params - read VPD parameters from VPD EEPROM
* @adapter: adapter to read
* Card information is normally at VPD_BASE but some early cards had
* it at 0.
*/
- ret = t3_seeprom_read(adapter, VPD_BASE, (u32 *)&vpd);
+ ret = t3_seeprom_read(adapter, VPD_BASE, (__le32 *)&vpd);
if (ret)
return ret;
addr = vpd.id_tag == 0x82 ? VPD_BASE : 0;
for (i = 0; i < sizeof(vpd); i += 4) {
ret = t3_seeprom_read(adapter, addr + i,
- (u32 *)((u8 *)&vpd + i));
+ (__le32 *)((u8 *)&vpd + i));
if (ret)
return ret;
}
p->port_type[0] = uses_xaui(adapter) ? 1 : 2;
p->port_type[1] = uses_xaui(adapter) ? 6 : 2;
} else {
- p->port_type[0] = hex2int(vpd.port0_data[0]);
- p->port_type[1] = hex2int(vpd.port1_data[0]);
+ p->port_type[0] = hex_to_bin(vpd.port0_data[0]);
+ p->port_type[1] = hex_to_bin(vpd.port1_data[0]);
p->xauicfg[0] = simple_strtoul(vpd.xaui0cfg_data, NULL, 16);
p->xauicfg[1] = simple_strtoul(vpd.xaui1cfg_data, NULL, 16);
}
for (i = 0; i < 6; i++)
- p->eth_base[i] = hex2int(vpd.na_data[2 * i]) * 16 +
- hex2int(vpd.na_data[2 * i + 1]);
+ p->eth_base[i] = hex_to_bin(vpd.na_data[2 * i]) * 16 +
+ hex_to_bin(vpd.na_data[2 * i + 1]);
return 0;
}
SF_ERASE_SECTOR = 0xd8, /* erase sector */
FW_FLASH_BOOT_ADDR = 0x70000, /* start address of FW in flash */
- FW_VERS_ADDR = 0x77ffc, /* flash address holding FW version */
+ FW_VERS_ADDR = 0x7fffc, /* flash address holding FW version */
FW_MIN_SIZE = 8 /* at least version and csum */
};
* (i.e., big-endian), otherwise as 32-bit words in the platform's
* natural endianess.
*/
-int t3_read_flash(struct adapter *adapter, unsigned int addr,
- unsigned int nwords, u32 *data, int byte_oriented)
+static int t3_read_flash(struct adapter *adapter, unsigned int addr,
+ unsigned int nwords, u32 *data, int byte_oriented)
{
int ret;
1, 1, 5, 1);
if (ret)
return ret;
-
+
*vers = t3_read_reg(adapter, A_TP_EMBED_OP_FIELD1);
return 0;
/**
* t3_check_tpsram_version - read the tp sram version
* @adapter: the adapter
- * @must_load: set to 1 if loading a new microcode image is required
*
* Reads the protocol sram version from flash.
*/
-int t3_check_tpsram_version(struct adapter *adapter, int *must_load)
+int t3_check_tpsram_version(struct adapter *adapter)
{
int ret;
u32 vers;
if (adapter->params.rev == T3_REV_A)
return 0;
- *must_load = 1;
ret = t3_get_tp_version(adapter, &vers);
if (ret)
major = G_TP_VERSION_MAJOR(vers);
minor = G_TP_VERSION_MINOR(vers);
- if (major == TP_VERSION_MAJOR && minor == TP_VERSION_MINOR)
+ if (major == TP_VERSION_MAJOR && minor == TP_VERSION_MINOR)
return 0;
-
- if (major != TP_VERSION_MAJOR)
- CH_ERR(adapter, "found wrong TP version (%u.%u), "
- "driver needs version %d.%d\n", major, minor,
- TP_VERSION_MAJOR, TP_VERSION_MINOR);
else {
- *must_load = 0;
CH_ERR(adapter, "found wrong TP version (%u.%u), "
"driver compiled for version %d.%d\n", major, minor,
TP_VERSION_MAJOR, TP_VERSION_MINOR);
}
/**
- * t3_check_tpsram - check if provided protocol SRAM
+ * t3_check_tpsram - check if provided protocol SRAM
* is compatible with this driver
* @adapter: the adapter
* @tp_sram: the firmware image to write
* Checks if an adapter's tp sram is compatible with the driver.
* Returns 0 if the versions are compatible, a negative error otherwise.
*/
-int t3_check_tpsram(struct adapter *adapter, u8 *tp_sram, unsigned int size)
+int t3_check_tpsram(struct adapter *adapter, const u8 *tp_sram,
+ unsigned int size)
{
u32 csum;
unsigned int i;
- const u32 *p = (const u32 *)tp_sram;
+ const __be32 *p = (const __be32 *)tp_sram;
/* Verify checksum */
for (csum = 0, i = 0; i < size / sizeof(csum); i++)
/**
* t3_check_fw_version - check if the FW is compatible with this driver
* @adapter: the adapter
- * @must_load: set to 1 if loading a new FW image is required
-
+ *
* Checks if an adapter's FW is compatible with the driver. Returns 0
* if the versions are compatible, a negative error otherwise.
*/
-int t3_check_fw_version(struct adapter *adapter, int *must_load)
+int t3_check_fw_version(struct adapter *adapter)
{
int ret;
u32 vers;
unsigned int type, major, minor;
- *must_load = 1;
ret = t3_get_fw_version(adapter, &vers);
if (ret)
return ret;
if (type == FW_VERSION_T3 && major == FW_VERSION_MAJOR &&
minor == FW_VERSION_MINOR)
return 0;
-
- if (major != FW_VERSION_MAJOR)
- CH_ERR(adapter, "found wrong FW version(%u.%u), "
- "driver needs version %u.%u\n", major, minor,
- FW_VERSION_MAJOR, FW_VERSION_MINOR);
+ else if (major != FW_VERSION_MAJOR || minor < FW_VERSION_MINOR)
+ CH_WARN(adapter, "found old FW minor version(%u.%u), "
+ "driver compiled for version %u.%u\n", major, minor,
+ FW_VERSION_MAJOR, FW_VERSION_MINOR);
else {
- *must_load = 0;
- CH_WARN(adapter, "found wrong FW minor version(%u.%u), "
+ CH_WARN(adapter, "found newer FW version(%u.%u), "
"driver compiled for version %u.%u\n", major, minor,
FW_VERSION_MAJOR, FW_VERSION_MINOR);
+ return 0;
}
-
return -EINVAL;
}
{
u32 csum;
unsigned int i;
- const u32 *p = (const u32 *)fw_data;
+ const __be32 *p = (const __be32 *)fw_data;
int ret, addr, fw_sector = FW_FLASH_BOOT_ADDR >> 16;
if ((size & 3) || size < FW_MIN_SIZE)
return ret;
}
+static void t3_gate_rx_traffic(struct cmac *mac, u32 *rx_cfg,
+ u32 *rx_hash_high, u32 *rx_hash_low)
+{
+ /* stop Rx unicast traffic */
+ t3_mac_disable_exact_filters(mac);
+
+ /* stop broadcast, multicast, promiscuous mode traffic */
+ *rx_cfg = t3_read_reg(mac->adapter, A_XGM_RX_CFG);
+ t3_set_reg_field(mac->adapter, A_XGM_RX_CFG,
+ F_ENHASHMCAST | F_DISBCAST | F_COPYALLFRAMES,
+ F_DISBCAST);
+
+ *rx_hash_high = t3_read_reg(mac->adapter, A_XGM_RX_HASH_HIGH);
+ t3_write_reg(mac->adapter, A_XGM_RX_HASH_HIGH, 0);
+
+ *rx_hash_low = t3_read_reg(mac->adapter, A_XGM_RX_HASH_LOW);
+ t3_write_reg(mac->adapter, A_XGM_RX_HASH_LOW, 0);
+
+ /* Leave time to drain max RX fifo */
+ msleep(1);
+}
+
+static void t3_open_rx_traffic(struct cmac *mac, u32 rx_cfg,
+ u32 rx_hash_high, u32 rx_hash_low)
+{
+ t3_mac_enable_exact_filters(mac);
+ t3_set_reg_field(mac->adapter, A_XGM_RX_CFG,
+ F_ENHASHMCAST | F_DISBCAST | F_COPYALLFRAMES,
+ rx_cfg);
+ t3_write_reg(mac->adapter, A_XGM_RX_HASH_HIGH, rx_hash_high);
+ t3_write_reg(mac->adapter, A_XGM_RX_HASH_LOW, rx_hash_low);
+}
/**
* t3_link_changed - handle interface link changes
phy->ops->get_link_status(phy, &link_ok, &speed, &duplex, &fc);
+ if (!lc->link_ok && link_ok) {
+ u32 rx_cfg, rx_hash_high, rx_hash_low;
+ u32 status;
+
+ t3_xgm_intr_enable(adapter, port_id);
+ t3_gate_rx_traffic(mac, &rx_cfg, &rx_hash_high, &rx_hash_low);
+ t3_write_reg(adapter, A_XGM_RX_CTRL + mac->offset, 0);
+ t3_mac_enable(mac, MAC_DIRECTION_RX);
+
+ status = t3_read_reg(adapter, A_XGM_INT_STATUS + mac->offset);
+ if (status & F_LINKFAULTCHANGE) {
+ mac->stats.link_faults++;
+ pi->link_fault = 1;
+ }
+ t3_open_rx_traffic(mac, rx_cfg, rx_hash_high, rx_hash_low);
+ }
+
+ if (lc->requested_fc & PAUSE_AUTONEG)
+ fc &= lc->requested_fc;
+ else
+ fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
+
+ if (link_ok == lc->link_ok && speed == lc->speed &&
+ duplex == lc->duplex && fc == lc->fc)
+ return; /* nothing changed */
+
if (link_ok != lc->link_ok && adapter->params.rev > 0 &&
uses_xaui(adapter)) {
if (link_ok)
lc->link_ok = link_ok;
lc->speed = speed < 0 ? SPEED_INVALID : speed;
lc->duplex = duplex < 0 ? DUPLEX_INVALID : duplex;
- if (lc->requested_fc & PAUSE_AUTONEG)
- fc &= lc->requested_fc;
- else
- fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
if (link_ok && speed >= 0 && lc->autoneg == AUTONEG_ENABLE) {
/* Set MAC speed, duplex, and flow control to match PHY. */
lc->fc = fc;
}
- t3_os_link_changed(adapter, port_id, link_ok, speed, duplex, fc);
+ t3_os_link_changed(adapter, port_id, link_ok && !pi->link_fault,
+ speed, duplex, fc);
+}
+
+void t3_link_fault(struct adapter *adapter, int port_id)
+{
+ struct port_info *pi = adap2pinfo(adapter, port_id);
+ struct cmac *mac = &pi->mac;
+ struct cphy *phy = &pi->phy;
+ struct link_config *lc = &pi->link_config;
+ int link_ok, speed, duplex, fc, link_fault;
+ u32 rx_cfg, rx_hash_high, rx_hash_low;
+
+ t3_gate_rx_traffic(mac, &rx_cfg, &rx_hash_high, &rx_hash_low);
+
+ if (adapter->params.rev > 0 && uses_xaui(adapter))
+ t3_write_reg(adapter, A_XGM_XAUI_ACT_CTRL + mac->offset, 0);
+
+ t3_write_reg(adapter, A_XGM_RX_CTRL + mac->offset, 0);
+ t3_mac_enable(mac, MAC_DIRECTION_RX);
+
+ t3_open_rx_traffic(mac, rx_cfg, rx_hash_high, rx_hash_low);
+
+ link_fault = t3_read_reg(adapter,
+ A_XGM_INT_STATUS + mac->offset);
+ link_fault &= F_LINKFAULTCHANGE;
+
+ link_ok = lc->link_ok;
+ speed = lc->speed;
+ duplex = lc->duplex;
+ fc = lc->fc;
+
+ phy->ops->get_link_status(phy, &link_ok, &speed, &duplex, &fc);
+
+ if (link_fault) {
+ lc->link_ok = 0;
+ lc->speed = SPEED_INVALID;
+ lc->duplex = DUPLEX_INVALID;
+
+ t3_os_link_fault(adapter, port_id, 0);
+
+ /* Account link faults only when the phy reports a link up */
+ if (link_ok)
+ mac->stats.link_faults++;
+ } else {
+ if (link_ok)
+ t3_write_reg(adapter, A_XGM_XAUI_ACT_CTRL + mac->offset,
+ F_TXACTENABLE | F_RXEN);
+
+ pi->link_fault = 0;
+ lc->link_ok = (unsigned char)link_ok;
+ lc->speed = speed < 0 ? SPEED_INVALID : speed;
+ lc->duplex = duplex < 0 ? DUPLEX_INVALID : duplex;
+ t3_os_link_fault(adapter, port_id, link_ok);
+ }
}
/**
fc);
/* Also disables autoneg */
phy->ops->set_speed_duplex(phy, lc->speed, lc->duplex);
- phy->ops->reset(phy, 0);
} else
phy->ops->autoneg_enable(phy);
} else {
unsigned int mask; /* bits to check in interrupt status */
const char *msg; /* message to print or NULL */
short stat_idx; /* stat counter to increment or -1 */
- unsigned short fatal:1; /* whether the condition reported is fatal */
+ unsigned short fatal; /* whether the condition reported is fatal */
};
/**
fatal++;
CH_ALERT(adapter, "%s (0x%x)\n",
acts->msg, status & acts->mask);
+ status &= ~acts->mask;
} else if (acts->msg)
CH_WARN(adapter, "%s (0x%x)\n",
acts->msg, status & acts->mask);
return fatal;
}
-#define SGE_INTR_MASK (F_RSPQDISABLED)
+#define SGE_INTR_MASK (F_RSPQDISABLED | \
+ F_UC_REQ_FRAMINGERROR | F_R_REQ_FRAMINGERROR | \
+ F_CPPARITYERROR | F_OCPARITYERROR | F_RCPARITYERROR | \
+ F_IRPARITYERROR | V_ITPARITYERROR(M_ITPARITYERROR) | \
+ V_FLPARITYERROR(M_FLPARITYERROR) | F_LODRBPARITYERROR | \
+ F_HIDRBPARITYERROR | F_LORCQPARITYERROR | \
+ F_HIRCQPARITYERROR | F_LOPRIORITYDBFULL | \
+ F_HIPRIORITYDBFULL | F_LOPRIORITYDBEMPTY | \
+ F_HIPRIORITYDBEMPTY | F_HIPIODRBDROPERR | \
+ F_LOPIODRBDROPERR)
#define MC5_INTR_MASK (F_PARITYERR | F_ACTRGNFULL | F_UNKNOWNCMD | \
F_REQQPARERR | F_DISPQPARERR | F_DELACTEMPTY | \
F_NFASRCHFAIL)
#define MC7_INTR_MASK (F_AE | F_UE | F_CE | V_PE(M_PE))
#define XGM_INTR_MASK (V_TXFIFO_PRTY_ERR(M_TXFIFO_PRTY_ERR) | \
V_RXFIFO_PRTY_ERR(M_RXFIFO_PRTY_ERR) | \
- F_TXFIFO_UNDERRUN | F_RXFIFO_OVERFLOW)
+ F_TXFIFO_UNDERRUN)
#define PCIX_INTR_MASK (F_MSTDETPARERR | F_SIGTARABT | F_RCVTARABT | \
F_RCVMSTABT | F_SIGSYSERR | F_DETPARERR | \
F_SPLCMPDIS | F_UNXSPLCMP | F_RCVSPLCMPERR | \
#define PCIE_INTR_MASK (F_UNXSPLCPLERRR | F_UNXSPLCPLERRC | F_PCIE_PIOPARERR |\
F_PCIE_WFPARERR | F_PCIE_RFPARERR | F_PCIE_CFPARERR | \
/* V_PCIE_MSIXPARERR(M_PCIE_MSIXPARERR) | */ \
- V_BISTERR(M_BISTERR) | F_PEXERR)
-#define ULPRX_INTR_MASK F_PARERR
-#define ULPTX_INTR_MASK 0
-#define CPLSW_INTR_MASK (F_TP_FRAMING_ERROR | \
+ F_RETRYBUFPARERR | F_RETRYLUTPARERR | F_RXPARERR | \
+ F_TXPARERR | V_BISTERR(M_BISTERR))
+#define ULPRX_INTR_MASK (F_PARERRDATA | F_PARERRPCMD | F_ARBPF1PERR | \
+ F_ARBPF0PERR | F_ARBFPERR | F_PCMDMUXPERR | \
+ F_DATASELFRAMEERR1 | F_DATASELFRAMEERR0)
+#define ULPTX_INTR_MASK 0xfc
+#define CPLSW_INTR_MASK (F_CIM_OP_MAP_PERR | F_TP_FRAMING_ERROR | \
F_SGE_FRAMING_ERROR | F_CIM_FRAMING_ERROR | \
F_ZERO_SWITCH_ERROR)
#define CIM_INTR_MASK (F_BLKWRPLINT | F_BLKRDPLINT | F_BLKWRCTLINT | \
F_BLKRDCTLINT | F_BLKWRFLASHINT | F_BLKRDFLASHINT | \
F_SGLWRFLASHINT | F_WRBLKFLASHINT | F_BLKWRBOOTINT | \
- F_FLASHRANGEINT | F_SDRAMRANGEINT | F_RSVDSPACEINT)
+ F_FLASHRANGEINT | F_SDRAMRANGEINT | F_RSVDSPACEINT | \
+ F_DRAMPARERR | F_ICACHEPARERR | F_DCACHEPARERR | \
+ F_OBQSGEPARERR | F_OBQULPHIPARERR | F_OBQULPLOPARERR | \
+ F_IBQSGELOPARERR | F_IBQSGEHIPARERR | F_IBQULPPARERR | \
+ F_IBQTPPARERR | F_ITAGPARERR | F_DTAGPARERR)
#define PMTX_INTR_MASK (F_ZERO_C_CMD_ERROR | ICSPI_FRM_ERR | OESPI_FRM_ERR | \
V_ICSPI_PAR_ERROR(M_ICSPI_PAR_ERROR) | \
V_OESPI_PAR_ERROR(M_OESPI_PAR_ERROR))
V_TX1TPPARERRENB(M_TX1TPPARERRENB) | \
V_RXTPPARERRENB(M_RXTPPARERRENB) | \
V_MCAPARERRENB(M_MCAPARERRENB))
+#define XGM_EXTRA_INTR_MASK (F_LINKFAULTCHANGE)
#define PL_INTR_MASK (F_T3DBG | F_XGMAC0_0 | F_XGMAC0_1 | F_MC5A | F_PM1_TX | \
F_PM1_RX | F_ULP2_TX | F_ULP2_RX | F_TP1 | F_CIM | \
F_MC7_CM | F_MC7_PMTX | F_MC7_PMRX | F_SGE3 | F_PCIM0 | \
F_MPS0 | F_CPL_SWITCH)
-
/*
* Interrupt handler for the PCIX1 module.
*/
{F_PCIE_CFPARERR, "PCI command FIFO parity error", -1, 1},
{V_PCIE_MSIXPARERR(M_PCIE_MSIXPARERR),
"PCI MSI-X table/PBA parity error", -1, 1},
+ {F_RETRYBUFPARERR, "PCI retry buffer parity error", -1, 1},
+ {F_RETRYLUTPARERR, "PCI retry LUT parity error", -1, 1},
+ {F_RXPARERR, "PCI Rx parity error", -1, 1},
+ {F_TXPARERR, "PCI Tx parity error", -1, 1},
{V_BISTERR(M_BISTERR), "PCI BIST error", -1, 1},
{0}
};
{0}
};
+ static struct intr_info tp_intr_info_t3c[] = {
+ {0x1fffffff, "TP parity error", -1, 1},
+ {F_FLMRXFLSTEMPTY, "TP out of Rx pages", -1, 1},
+ {F_FLMTXFLSTEMPTY, "TP out of Tx pages", -1, 1},
+ {0}
+ };
+
if (t3_handle_intr_status(adapter, A_TP_INT_CAUSE, 0xffffffff,
- tp_intr_info, NULL))
+ adapter->params.rev < T3_REV_C ?
+ tp_intr_info : tp_intr_info_t3c, NULL))
t3_fatal_err(adapter);
}
{F_BLKWRCTLINT, "CIM block write to CTL space", -1, 1},
{F_BLKRDPLINT, "CIM block read from PL space", -1, 1},
{F_BLKWRPLINT, "CIM block write to PL space", -1, 1},
+ {F_DRAMPARERR, "CIM DRAM parity error", -1, 1},
+ {F_ICACHEPARERR, "CIM icache parity error", -1, 1},
+ {F_DCACHEPARERR, "CIM dcache parity error", -1, 1},
+ {F_OBQSGEPARERR, "CIM OBQ SGE parity error", -1, 1},
+ {F_OBQULPHIPARERR, "CIM OBQ ULPHI parity error", -1, 1},
+ {F_OBQULPLOPARERR, "CIM OBQ ULPLO parity error", -1, 1},
+ {F_IBQSGELOPARERR, "CIM IBQ SGELO parity error", -1, 1},
+ {F_IBQSGEHIPARERR, "CIM IBQ SGEHI parity error", -1, 1},
+ {F_IBQULPPARERR, "CIM IBQ ULP parity error", -1, 1},
+ {F_IBQTPPARERR, "CIM IBQ TP parity error", -1, 1},
+ {F_ITAGPARERR, "CIM itag parity error", -1, 1},
+ {F_DTAGPARERR, "CIM dtag parity error", -1, 1},
{0}
};
static void ulprx_intr_handler(struct adapter *adapter)
{
static const struct intr_info ulprx_intr_info[] = {
- {F_PARERR, "ULP RX parity error", -1, 1},
+ {F_PARERRDATA, "ULP RX data parity error", -1, 1},
+ {F_PARERRPCMD, "ULP RX command parity error", -1, 1},
+ {F_ARBPF1PERR, "ULP RX ArbPF1 parity error", -1, 1},
+ {F_ARBPF0PERR, "ULP RX ArbPF0 parity error", -1, 1},
+ {F_ARBFPERR, "ULP RX ArbF parity error", -1, 1},
+ {F_PCMDMUXPERR, "ULP RX PCMDMUX parity error", -1, 1},
+ {F_DATASELFRAMEERR1, "ULP RX frame error", -1, 1},
+ {F_DATASELFRAMEERR0, "ULP RX frame error", -1, 1},
{0}
};
STAT_ULP_CH0_PBL_OOB, 0},
{F_PBL_BOUND_ERR_CH1, "ULP TX channel 1 PBL out of bounds",
STAT_ULP_CH1_PBL_OOB, 0},
+ {0xfc, "ULP TX parity error", -1, 1},
{0}
};
static void cplsw_intr_handler(struct adapter *adapter)
{
static const struct intr_info cplsw_intr_info[] = {
-/* { F_CIM_OVFL_ERROR, "CPL switch CIM overflow", -1, 1 }, */
+ {F_CIM_OP_MAP_PERR, "CPL switch CIM parity error", -1, 1},
+ {F_CIM_OVFL_ERROR, "CPL switch CIM overflow", -1, 1},
{F_TP_FRAMING_ERROR, "CPL switch TP framing error", -1, 1},
{F_SGE_FRAMING_ERROR, "CPL switch SGE framing error", -1, 1},
{F_CIM_FRAMING_ERROR, "CPL switch CIM framing error", -1, 1},
static int mac_intr_handler(struct adapter *adap, unsigned int idx)
{
struct cmac *mac = &adap2pinfo(adap, idx)->mac;
- u32 cause = t3_read_reg(adap, A_XGM_INT_CAUSE + mac->offset);
+ /*
+ * We mask out interrupt causes for which we're not taking interrupts.
+ * This allows us to use polling logic to monitor some of the other
+ * conditions when taking interrupts would impose too much load on the
+ * system.
+ */
+ u32 cause = t3_read_reg(adap, A_XGM_INT_CAUSE + mac->offset) &
+ ~F_RXFIFO_OVERFLOW;
if (cause & V_TXFIFO_PRTY_ERR(M_TXFIFO_PRTY_ERR)) {
mac->stats.tx_fifo_parity_err++;
mac->stats.xaui_pcs_ctc_err++;
if (cause & F_XAUIPCSALIGNCHANGE)
mac->stats.xaui_pcs_align_change++;
+ if (cause & F_XGM_INT) {
+ t3_set_reg_field(adap,
+ A_XGM_INT_ENABLE + mac->offset,
+ F_XGM_INT, 0);
+ mac->stats.link_faults++;
+
+ t3_os_link_fault_handler(adap, idx);
+ }
- t3_write_reg(adap, A_XGM_INT_CAUSE + mac->offset, cause);
if (cause & XGM_INTR_FATAL)
t3_fatal_err(adap);
+
+ t3_write_reg(adap, A_XGM_INT_CAUSE + mac->offset, cause);
return cause != 0;
}
*/
int t3_phy_intr_handler(struct adapter *adapter)
{
- u32 mask, gpi = adapter_info(adapter)->gpio_intr;
u32 i, cause = t3_read_reg(adapter, A_T3DBG_INT_CAUSE);
for_each_port(adapter, i) {
struct port_info *p = adap2pinfo(adapter, i);
- mask = gpi - (gpi & (gpi - 1));
- gpi -= mask;
-
- if (!(p->port_type->caps & SUPPORTED_IRQ))
+ if (!(p->phy.caps & SUPPORTED_IRQ))
continue;
- if (cause & mask) {
+ if (cause & (1 << adapter_info(adapter)->gpio_intr[i])) {
int phy_cause = p->phy.ops->intr_handler(&p->phy);
if (phy_cause & cphy_cause_link_change)
t3_link_changed(adapter, i);
if (phy_cause & cphy_cause_fifo_error)
p->phy.fifo_errors++;
+ if (phy_cause & cphy_cause_module_change)
+ t3_os_phymod_changed(adapter, i);
}
}
return 1;
}
+static unsigned int calc_gpio_intr(struct adapter *adap)
+{
+ unsigned int i, gpi_intr = 0;
+
+ for_each_port(adap, i)
+ if ((adap2pinfo(adap, i)->phy.caps & SUPPORTED_IRQ) &&
+ adapter_info(adap)->gpio_intr[i])
+ gpi_intr |= 1 << adapter_info(adap)->gpio_intr[i];
+ return gpi_intr;
+}
+
/**
* t3_intr_enable - enable interrupts
* @adapter: the adapter whose interrupts should be enabled
MC7_INTR_MASK},
{A_MC5_DB_INT_ENABLE, MC5_INTR_MASK},
{A_ULPRX_INT_ENABLE, ULPRX_INTR_MASK},
- {A_TP_INT_ENABLE, 0x3bfffff},
{A_PM1_TX_INT_ENABLE, PMTX_INTR_MASK},
{A_PM1_RX_INT_ENABLE, PMRX_INTR_MASK},
{A_CIM_HOST_INT_ENABLE, CIM_INTR_MASK},
adapter->slow_intr_mask = PL_INTR_MASK;
t3_write_regs(adapter, intr_en_avp, ARRAY_SIZE(intr_en_avp), 0);
+ t3_write_reg(adapter, A_TP_INT_ENABLE,
+ adapter->params.rev >= T3_REV_C ? 0x2bfffff : 0x3bfffff);
if (adapter->params.rev > 0) {
t3_write_reg(adapter, A_CPL_INTR_ENABLE,
t3_write_reg(adapter, A_ULPTX_INT_ENABLE, ULPTX_INTR_MASK);
}
- t3_write_reg(adapter, A_T3DBG_GPIO_ACT_LOW,
- adapter_info(adapter)->gpio_intr);
- t3_write_reg(adapter, A_T3DBG_INT_ENABLE,
- adapter_info(adapter)->gpio_intr);
+ t3_write_reg(adapter, A_T3DBG_INT_ENABLE, calc_gpio_intr(adapter));
+
if (is_pcie(adapter))
t3_write_reg(adapter, A_PCIE_INT_ENABLE, PCIE_INTR_MASK);
else
t3_read_reg(adapter, A_PL_INT_CAUSE0); /* flush */
}
+void t3_xgm_intr_enable(struct adapter *adapter, int idx)
+{
+ struct port_info *pi = adap2pinfo(adapter, idx);
+
+ t3_write_reg(adapter, A_XGM_XGM_INT_ENABLE + pi->mac.offset,
+ XGM_EXTRA_INTR_MASK);
+}
+
+void t3_xgm_intr_disable(struct adapter *adapter, int idx)
+{
+ struct port_info *pi = adap2pinfo(adapter, idx);
+
+ t3_write_reg(adapter, A_XGM_XGM_INT_DISABLE + pi->mac.offset,
+ 0x7ff);
+}
+
/**
* t3_port_intr_enable - enable port-specific interrupts
* @adapter: associated adapter
* Clear port-specific (i.e., MAC and PHY) interrupts for the given
* adapter port.
*/
-void t3_port_intr_clear(struct adapter *adapter, int idx)
+static void t3_port_intr_clear(struct adapter *adapter, int idx)
{
struct cphy *phy = &adap2pinfo(adapter, idx)->phy;
static int t3_sge_write_context(struct adapter *adapter, unsigned int id,
unsigned int type)
{
- t3_write_reg(adapter, A_SG_CONTEXT_MASK0, 0xffffffff);
- t3_write_reg(adapter, A_SG_CONTEXT_MASK1, 0xffffffff);
- t3_write_reg(adapter, A_SG_CONTEXT_MASK2, 0xffffffff);
- t3_write_reg(adapter, A_SG_CONTEXT_MASK3, 0xffffffff);
+ if (type == F_RESPONSEQ) {
+ /*
+ * Can't write the Response Queue Context bits for
+ * Interrupt Armed or the Reserve bits after the chip
+ * has been initialized out of reset. Writing to these
+ * bits can confuse the hardware.
+ */
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK0, 0xffffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK1, 0xffffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK2, 0x17ffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK3, 0xffffffff);
+ } else {
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK0, 0xffffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK1, 0xffffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK2, 0xffffffff);
+ t3_write_reg(adapter, A_SG_CONTEXT_MASK3, 0xffffffff);
+ }
t3_write_reg(adapter, A_SG_CONTEXT_CMD,
V_CONTEXT_CMD_OPCODE(1) | type | V_CONTEXT(id));
return t3_wait_op_done(adapter, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY,
}
/**
+ * clear_sge_ctxt - completely clear an SGE context
+ * @adapter: the adapter
+ * @id: the context id
+ * @type: the context type
+ *
+ * Completely clear an SGE context. Used predominantly at post-reset
+ * initialization. Note in particular that we don't skip writing to any
+ * "sensitive bits" in the contexts the way that t3_sge_write_context()
+ * does ...
+ */
+static int clear_sge_ctxt(struct adapter *adap, unsigned int id,
+ unsigned int type)
+{
+ t3_write_reg(adap, A_SG_CONTEXT_DATA0, 0);
+ t3_write_reg(adap, A_SG_CONTEXT_DATA1, 0);
+ t3_write_reg(adap, A_SG_CONTEXT_DATA2, 0);
+ t3_write_reg(adap, A_SG_CONTEXT_DATA3, 0);
+ t3_write_reg(adap, A_SG_CONTEXT_MASK0, 0xffffffff);
+ t3_write_reg(adap, A_SG_CONTEXT_MASK1, 0xffffffff);
+ t3_write_reg(adap, A_SG_CONTEXT_MASK2, 0xffffffff);
+ t3_write_reg(adap, A_SG_CONTEXT_MASK3, 0xffffffff);
+ t3_write_reg(adap, A_SG_CONTEXT_CMD,
+ V_CONTEXT_CMD_OPCODE(1) | type | V_CONTEXT(id));
+ return t3_wait_op_done(adap, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY,
+ 0, SG_CONTEXT_CMD_ATTEMPTS, 1);
+}
+
+/**
* t3_sge_init_ecntxt - initialize an SGE egress context
* @adapter: the adapter to configure
* @id: the context id
}
/**
- * t3_sge_read_context - read an SGE context
- * @type: the context type
- * @adapter: the adapter
- * @id: the context id
- * @data: holds the retrieved context
- *
- * Read an SGE egress context. The caller is responsible for ensuring
- * only one context operation occurs at a time.
- */
-static int t3_sge_read_context(unsigned int type, struct adapter *adapter,
- unsigned int id, u32 data[4])
-{
- if (t3_read_reg(adapter, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
- return -EBUSY;
-
- t3_write_reg(adapter, A_SG_CONTEXT_CMD,
- V_CONTEXT_CMD_OPCODE(0) | type | V_CONTEXT(id));
- if (t3_wait_op_done(adapter, A_SG_CONTEXT_CMD, F_CONTEXT_CMD_BUSY, 0,
- SG_CONTEXT_CMD_ATTEMPTS, 1))
- return -EIO;
- data[0] = t3_read_reg(adapter, A_SG_CONTEXT_DATA0);
- data[1] = t3_read_reg(adapter, A_SG_CONTEXT_DATA1);
- data[2] = t3_read_reg(adapter, A_SG_CONTEXT_DATA2);
- data[3] = t3_read_reg(adapter, A_SG_CONTEXT_DATA3);
- return 0;
-}
-
-/**
- * t3_sge_read_ecntxt - read an SGE egress context
- * @adapter: the adapter
- * @id: the context id
- * @data: holds the retrieved context
- *
- * Read an SGE egress context. The caller is responsible for ensuring
- * only one context operation occurs at a time.
- */
-int t3_sge_read_ecntxt(struct adapter *adapter, unsigned int id, u32 data[4])
-{
- if (id >= 65536)
- return -EINVAL;
- return t3_sge_read_context(F_EGRESS, adapter, id, data);
-}
-
-/**
- * t3_sge_read_cq - read an SGE CQ context
- * @adapter: the adapter
- * @id: the context id
- * @data: holds the retrieved context
- *
- * Read an SGE CQ context. The caller is responsible for ensuring
- * only one context operation occurs at a time.
- */
-int t3_sge_read_cq(struct adapter *adapter, unsigned int id, u32 data[4])
-{
- if (id >= 65536)
- return -EINVAL;
- return t3_sge_read_context(F_CQ, adapter, id, data);
-}
-
-/**
- * t3_sge_read_fl - read an SGE free-list context
- * @adapter: the adapter
- * @id: the context id
- * @data: holds the retrieved context
- *
- * Read an SGE free-list context. The caller is responsible for ensuring
- * only one context operation occurs at a time.
- */
-int t3_sge_read_fl(struct adapter *adapter, unsigned int id, u32 data[4])
-{
- if (id >= SGE_QSETS * 2)
- return -EINVAL;
- return t3_sge_read_context(F_FREELIST, adapter, id, data);
-}
-
-/**
- * t3_sge_read_rspq - read an SGE response queue context
- * @adapter: the adapter
- * @id: the context id
- * @data: holds the retrieved context
- *
- * Read an SGE response queue context. The caller is responsible for
- * ensuring only one context operation occurs at a time.
- */
-int t3_sge_read_rspq(struct adapter *adapter, unsigned int id, u32 data[4])
-{
- if (id >= SGE_QSETS)
- return -EINVAL;
- return t3_sge_read_context(F_RESPONSEQ, adapter, id, data);
-}
-
-/**
* t3_config_rss - configure Rx packet steering
* @adapter: the adapter
* @rss_config: RSS settings (written to TP_RSS_CONFIG)
}
/**
- * t3_read_rss - read the contents of the RSS tables
- * @adapter: the adapter
- * @lkup: holds the contents of the RSS lookup table
- * @map: holds the contents of the RSS map table
- *
- * Reads the contents of the receive packet steering tables.
- */
-int t3_read_rss(struct adapter *adapter, u8 * lkup, u16 *map)
-{
- int i;
- u32 val;
-
- if (lkup)
- for (i = 0; i < RSS_TABLE_SIZE; ++i) {
- t3_write_reg(adapter, A_TP_RSS_LKP_TABLE,
- 0xffff0000 | i);
- val = t3_read_reg(adapter, A_TP_RSS_LKP_TABLE);
- if (!(val & 0x80000000))
- return -EAGAIN;
- *lkup++ = val;
- *lkup++ = (val >> 8);
- }
-
- if (map)
- for (i = 0; i < RSS_TABLE_SIZE; ++i) {
- t3_write_reg(adapter, A_TP_RSS_MAP_TABLE,
- 0xffff0000 | i);
- val = t3_read_reg(adapter, A_TP_RSS_MAP_TABLE);
- if (!(val & 0x80000000))
- return -EAGAIN;
- *map++ = val;
- }
- return 0;
-}
-
-/**
* t3_tp_set_offload_mode - put TP in NIC/offload mode
* @adap: the adapter
* @enable: 1 to select offload mode, 0 for regular NIC
t3_write_reg((adap), A_ ## reg, (start)); \
start += size
-/*
+/**
* partition_mem - partition memory and configure TP memory settings
* @adap: the adapter
* @p: the TP parameters
F_TCPCHECKSUMOFFLOAD | V_IPTTL(64));
t3_write_reg(adap, A_TP_TCP_OPTIONS, V_MTUDEFAULT(576) |
F_MTUENABLE | V_WINDOWSCALEMODE(1) |
- V_TIMESTAMPSMODE(0) | V_SACKMODE(1) | V_SACKRX(1));
+ V_TIMESTAMPSMODE(1) | V_SACKMODE(1) | V_SACKRX(1));
t3_write_reg(adap, A_TP_DACK_CONFIG, V_AUTOSTATE3(1) |
V_AUTOSTATE2(1) | V_AUTOSTATE1(0) |
- V_BYTETHRESHOLD(16384) | V_MSSTHRESHOLD(2) |
+ V_BYTETHRESHOLD(26880) | V_MSSTHRESHOLD(2) |
F_AUTOCAREFUL | F_AUTOENABLE | V_DACK_MODE(1));
- t3_set_reg_field(adap, A_TP_IN_CONFIG, F_IPV6ENABLE | F_NICMODE,
+ t3_set_reg_field(adap, A_TP_IN_CONFIG, F_RXFBARBPRIO | F_TXFBARBPRIO,
F_IPV6ENABLE | F_NICMODE);
t3_write_reg(adap, A_TP_TX_RESOURCE_LIMIT, 0x18141814);
t3_write_reg(adap, A_TP_PARA_REG4, 0x5050105);
F_ENABLEEPCMDAFULL,
F_ENABLEOCSPIFULL |F_TXDEFERENABLE | F_HEARBEATDACK |
F_TXCONGESTIONMODE | F_RXCONGESTIONMODE);
- t3_set_reg_field(adap, A_TP_PC_CONFIG2, F_CHDRAFULL, 0);
+ t3_set_reg_field(adap, A_TP_PC_CONFIG2, F_CHDRAFULL,
+ F_ENABLEIPV6RSS | F_ENABLENONOFDTNLSYN |
+ F_ENABLEARPMISS | F_DISBLEDAPARBIT0);
t3_write_reg(adap, A_TP_PROXY_FLOW_CNTL, 1080);
t3_write_reg(adap, A_TP_PROXY_FLOW_CNTL, 1000);
-
+
if (adap->params.rev > 0) {
tp_wr_indirect(adap, A_TP_EGRESS_CONFIG, F_REWRITEFORCETOSIZE);
t3_set_reg_field(adap, A_TP_PARA_REG3, F_TXPACEAUTO,
} else
t3_set_reg_field(adap, A_TP_PARA_REG3, 0, F_TXPACEFIXED);
+ if (adap->params.rev == T3_REV_C)
+ t3_set_reg_field(adap, A_TP_PC_CONFIG,
+ V_TABLELATENCYDELTA(M_TABLELATENCYDELTA),
+ V_TABLELATENCYDELTA(4));
+
t3_write_reg(adap, A_TP_TX_MOD_QUEUE_WEIGHT1, 0);
t3_write_reg(adap, A_TP_TX_MOD_QUEUE_WEIGHT0, 0);
t3_write_reg(adap, A_TP_MOD_CHANNEL_WEIGHT, 0);
*
* Set the receive coalescing size and PSH bit handling.
*/
-int t3_tp_set_coalescing_size(struct adapter *adap, unsigned int size, int psh)
+static int t3_tp_set_coalescing_size(struct adapter *adap,
+ unsigned int size, int psh)
{
u32 val;
* Set TP's max receive size. This is the limit that applies when
* receive coalescing is disabled.
*/
-void t3_tp_set_max_rxsize(struct adapter *adap, unsigned int size)
+static void t3_tp_set_max_rxsize(struct adapter *adap, unsigned int size)
{
t3_write_reg(adap, A_TP_PARA_REG7,
V_PMMAXXFERLEN0(size) | V_PMMAXXFERLEN1(size));
}
-static void __devinit init_mtus(unsigned short mtus[])
+static void init_mtus(unsigned short mtus[])
{
/*
* See draft-mathis-plpmtud-00.txt for the values. The min is 88 so
* it can accomodate max size TCP/IP headers when SACK and timestamps
* are enabled and still have at least 8 bytes of payload.
*/
- mtus[1] = 88;
+ mtus[0] = 88;
mtus[1] = 88;
mtus[2] = 256;
mtus[3] = 512;
/*
* Initial congestion control parameters.
*/
-static void __devinit init_cong_ctrl(unsigned short *a, unsigned short *b)
+static void init_cong_ctrl(unsigned short *a, unsigned short *b)
{
a[0] = a[1] = a[2] = a[3] = a[4] = a[5] = a[6] = a[7] = a[8] = 1;
a[9] = 2;
}
/**
- * t3_read_hw_mtus - returns the values in the HW MTU table
- * @adap: the adapter
- * @mtus: where to store the HW MTU values
- *
- * Reads the HW MTU table.
- */
-void t3_read_hw_mtus(struct adapter *adap, unsigned short mtus[NMTUS])
-{
- int i;
-
- for (i = 0; i < NMTUS; ++i) {
- unsigned int val;
-
- t3_write_reg(adap, A_TP_MTU_TABLE, 0xff000000 | i);
- val = t3_read_reg(adap, A_TP_MTU_TABLE);
- mtus[i] = val & 0x3fff;
- }
-}
-
-/**
- * t3_get_cong_cntl_tab - reads the congestion control table
- * @adap: the adapter
- * @incr: where to store the alpha values
- *
- * Reads the additive increments programmed into the HW congestion
- * control table.
- */
-void t3_get_cong_cntl_tab(struct adapter *adap,
- unsigned short incr[NMTUS][NCCTRL_WIN])
-{
- unsigned int mtu, w;
-
- for (mtu = 0; mtu < NMTUS; ++mtu)
- for (w = 0; w < NCCTRL_WIN; ++w) {
- t3_write_reg(adap, A_TP_CCTRL_TABLE,
- 0xffff0000 | (mtu << 5) | w);
- incr[mtu][w] = t3_read_reg(adap, A_TP_CCTRL_TABLE) &
- 0x1fff;
- }
-}
-
-/**
* t3_tp_get_mib_stats - read TP's MIB counters
* @adap: the adapter
* @tps: holds the returned counter values
*
* Write the contents of the protocol SRAM.
*/
-int t3_set_proto_sram(struct adapter *adap, u8 *data)
+int t3_set_proto_sram(struct adapter *adap, const u8 *data)
{
int i;
- u32 *buf = (u32 *)data;
+ const __be32 *buf = (const __be32 *)data;
for (i = 0; i < PROTO_SRAM_LINES; i++) {
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD5, cpu_to_be32(*buf++));
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD4, cpu_to_be32(*buf++));
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD3, cpu_to_be32(*buf++));
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD2, cpu_to_be32(*buf++));
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD1, cpu_to_be32(*buf++));
-
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD5, be32_to_cpu(*buf++));
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD4, be32_to_cpu(*buf++));
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD3, be32_to_cpu(*buf++));
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD2, be32_to_cpu(*buf++));
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD1, be32_to_cpu(*buf++));
+
t3_write_reg(adap, A_TP_EMBED_OP_FIELD0, i << 1 | 1 << 31);
if (t3_wait_op_done(adap, A_TP_EMBED_OP_FIELD0, 1, 1, 5, 1))
return -EIO;
return busy;
}
-int t3_mps_set_active_ports(struct adapter *adap, unsigned int port_mask)
-{
- if (port_mask & ~((1 << adap->params.nports) - 1))
- return -EINVAL;
- t3_set_reg_field(adap, A_MPS_CFG, F_PORT1ACTIVE | F_PORT0ACTIVE,
- port_mask << S_PORT0ACTIVE);
- return 0;
-}
-
/*
- * Perform the bits of HW initialization that are dependent on the number
- * of available ports.
+ * Perform the bits of HW initialization that are dependent on the Tx
+ * channels being used.
*/
-static void init_hw_for_avail_ports(struct adapter *adap, int nports)
+static void chan_init_hw(struct adapter *adap, unsigned int chan_map)
{
int i;
- if (nports == 1) {
+ if (chan_map != 3) { /* one channel */
t3_set_reg_field(adap, A_ULPRX_CTL, F_ROUND_ROBIN, 0);
t3_set_reg_field(adap, A_ULPTX_CONFIG, F_CFG_RR_ARB, 0);
- t3_write_reg(adap, A_MPS_CFG, F_TPRXPORTEN | F_TPTXPORT0EN |
- F_PORT0ACTIVE | F_ENFORCEPKT);
- t3_write_reg(adap, A_PM1_TX_CFG, 0xffffffff);
- } else {
+ t3_write_reg(adap, A_MPS_CFG, F_TPRXPORTEN | F_ENFORCEPKT |
+ (chan_map == 1 ? F_TPTXPORT0EN | F_PORT0ACTIVE :
+ F_TPTXPORT1EN | F_PORT1ACTIVE));
+ t3_write_reg(adap, A_PM1_TX_CFG,
+ chan_map == 1 ? 0xffffffff : 0);
+ } else { /* two channels */
t3_set_reg_field(adap, A_ULPRX_CTL, 0, F_ROUND_ROBIN);
t3_set_reg_field(adap, A_ULPTX_CONFIG, 0, F_CFG_RR_ARB);
t3_write_reg(adap, A_ULPTX_DMA_WEIGHT,
{201, 321, 258, 450, 834, 1602}
};
- u16 val;
+ u16 val, devid;
unsigned int log2_width, pldsize;
unsigned int fst_trn_rx, fst_trn_tx, acklat, rpllmt;
adap->params.pci.pcie_cap_addr + PCI_EXP_DEVCTL,
&val);
pldsize = (val & PCI_EXP_DEVCTL_PAYLOAD) >> 5;
+
+ pci_read_config_word(adap->pdev, 0x2, &devid);
+ if (devid == 0x37) {
+ pci_write_config_word(adap->pdev,
+ adap->params.pci.pcie_cap_addr +
+ PCI_EXP_DEVCTL,
+ val & ~PCI_EXP_DEVCTL_READRQ &
+ ~PCI_EXP_DEVCTL_PAYLOAD);
+ pldsize = 0;
+ }
+
pci_read_config_word(adap->pdev,
adap->params.pci.pcie_cap_addr + PCI_EXP_LNKCTL,
&val);
V_REPLAYLMT(rpllmt));
t3_write_reg(adap, A_PCIE_PEX_ERR, 0xffffffff);
- t3_set_reg_field(adap, A_PCIE_CFG, F_PCIE_CLIDECEN, F_PCIE_CLIDECEN);
+ t3_set_reg_field(adap, A_PCIE_CFG, 0,
+ F_ENABLELINKDWNDRST | F_ENABLELINKDOWNRST |
+ F_PCIE_DMASTOPEN | F_PCIE_CLIDECEN);
}
/*
*/
int t3_init_hw(struct adapter *adapter, u32 fw_params)
{
- int err = -EIO, attempts = 100;
+ int err = -EIO, attempts, i;
const struct vpd_params *vpd = &adapter->params.vpd;
if (adapter->params.rev > 0)
adapter->params.mc5.nfilters,
adapter->params.mc5.nroutes))
goto out_err;
+
+ for (i = 0; i < 32; i++)
+ if (clear_sge_ctxt(adapter, i, F_CQ))
+ goto out_err;
}
if (tp_init(adapter, &adapter->params.tp))
if (is_pcie(adapter))
config_pcie(adapter);
else
- t3_set_reg_field(adapter, A_PCIX_CFG, 0, F_CLIDECEN);
+ t3_set_reg_field(adapter, A_PCIX_CFG, 0,
+ F_DMASTOPEN | F_CLIDECEN);
+
+ if (adapter->params.rev == T3_REV_C)
+ t3_set_reg_field(adapter, A_ULPTX_CONFIG, 0,
+ F_CFG_CQE_SOP_MASK);
t3_write_reg(adapter, A_PM1_RX_CFG, 0xffffffff);
t3_write_reg(adapter, A_PM1_RX_MODE, 0);
t3_write_reg(adapter, A_PM1_TX_MODE, 0);
- init_hw_for_avail_ports(adapter, adapter->params.nports);
+ chan_init_hw(adapter, adapter->params.chan_map);
t3_sge_init(adapter, &adapter->params.sge);
+ t3_set_reg_field(adapter, A_PL_RST, 0, F_FATALPERREN);
+
+ t3_write_reg(adapter, A_T3DBG_GPIO_ACT_LOW, calc_gpio_intr(adapter));
t3_write_reg(adapter, A_CIM_HOST_ACC_DATA, vpd->uclk | fw_params);
t3_write_reg(adapter, A_CIM_BOOT_CFG,
V_BOOTADDR(FW_FLASH_BOOT_ADDR >> 2));
t3_read_reg(adapter, A_CIM_BOOT_CFG); /* flush */
+ attempts = 100;
do { /* wait for uP to initialize */
msleep(20);
} while (t3_read_reg(adapter, A_CIM_HOST_ACC_DATA) && --attempts);
* Determines a card's PCI mode and associated parameters, such as speed
* and width.
*/
-static void __devinit get_pci_mode(struct adapter *adapter,
- struct pci_params *p)
+static void get_pci_mode(struct adapter *adapter, struct pci_params *p)
{
static unsigned short speed_map[] = { 33, 66, 100, 133 };
u32 pci_mode, pcie_cap;
* capabilities and default speed/duplex/flow-control/autonegotiation
* settings.
*/
-static void __devinit init_link_config(struct link_config *lc,
- unsigned int caps)
+static void init_link_config(struct link_config *lc, unsigned int caps)
{
lc->supported = caps;
lc->requested_speed = lc->speed = SPEED_INVALID;
* Calculates the size of an MC7 memory in bytes from the value of its
* configuration register.
*/
-static unsigned int __devinit mc7_calc_size(u32 cfg)
+static unsigned int mc7_calc_size(u32 cfg)
{
unsigned int width = G_WIDTH(cfg);
unsigned int banks = !!(cfg & F_BKS) + 1;
return MBs << 20;
}
-static void __devinit mc7_prep(struct adapter *adapter, struct mc7 *mc7,
- unsigned int base_addr, const char *name)
+static void mc7_prep(struct adapter *adapter, struct mc7 *mc7,
+ unsigned int base_addr, const char *name)
{
u32 cfg;
mc7->name = name;
mc7->offset = base_addr - MC7_PMRX_BASE_ADDR;
cfg = t3_read_reg(adapter, mc7->offset + A_MC7_CFG);
- mc7->size = mc7->size = G_DEN(cfg) == M_DEN ? 0 : mc7_calc_size(cfg);
+ mc7->size = G_DEN(cfg) == M_DEN ? 0 : mc7_calc_size(cfg);
mc7->width = G_WIDTH(cfg);
}
-void mac_prep(struct cmac *mac, struct adapter *adapter, int index)
+static void mac_prep(struct cmac *mac, struct adapter *adapter, int index)
{
+ u16 devid;
+
mac->adapter = adapter;
+ pci_read_config_word(adapter->pdev, 0x2, &devid);
+
+ if (devid == 0x37 && !adapter->params.vpd.xauicfg[1])
+ index = 0;
mac->offset = (XGMAC0_1_BASE_ADDR - XGMAC0_0_BASE_ADDR) * index;
mac->nucast = 1;
}
}
-void early_hw_init(struct adapter *adapter, const struct adapter_info *ai)
+static void early_hw_init(struct adapter *adapter,
+ const struct adapter_info *ai)
{
u32 val = V_PORTSPEED(is_10G(adapter) ? 3 : 2);
t3_write_reg(adapter, A_T3DBG_GPIO_EN,
ai->gpio_out | F_GPIO0_OEN | F_GPIO0_OUT_VAL);
t3_write_reg(adapter, A_MC5_DB_SERVER_INDEX, 0);
+ t3_write_reg(adapter, A_SG_OCO_BASE, V_BASE1(0xfff));
if (adapter->params.rev == 0 || !uses_xaui(adapter))
val |= F_ENRGMII;
}
/*
- * Reset the adapter.
+ * Reset the adapter.
* Older PCIe cards lose their config space during reset, PCI-X
* ones don't.
*/
-static int t3_reset_adapter(struct adapter *adapter)
+int t3_reset_adapter(struct adapter *adapter)
{
- int i, save_and_restore_pcie =
+ int i, save_and_restore_pcie =
adapter->params.rev < T3_REV_B2 && is_pcie(adapter);
uint16_t devid = 0;
return 0;
}
+static int init_parity(struct adapter *adap)
+{
+ int i, err, addr;
+
+ if (t3_read_reg(adap, A_SG_CONTEXT_CMD) & F_CONTEXT_CMD_BUSY)
+ return -EBUSY;
+
+ for (err = i = 0; !err && i < 16; i++)
+ err = clear_sge_ctxt(adap, i, F_EGRESS);
+ for (i = 0xfff0; !err && i <= 0xffff; i++)
+ err = clear_sge_ctxt(adap, i, F_EGRESS);
+ for (i = 0; !err && i < SGE_QSETS; i++)
+ err = clear_sge_ctxt(adap, i, F_RESPONSEQ);
+ if (err)
+ return err;
+
+ t3_write_reg(adap, A_CIM_IBQ_DBG_DATA, 0);
+ for (i = 0; i < 4; i++)
+ for (addr = 0; addr <= M_IBQDBGADDR; addr++) {
+ t3_write_reg(adap, A_CIM_IBQ_DBG_CFG, F_IBQDBGEN |
+ F_IBQDBGWR | V_IBQDBGQID(i) |
+ V_IBQDBGADDR(addr));
+ err = t3_wait_op_done(adap, A_CIM_IBQ_DBG_CFG,
+ F_IBQDBGBUSY, 0, 2, 1);
+ if (err)
+ return err;
+ }
+ return 0;
+}
+
/*
* Initialize adapter SW state for the various HW modules, set initial values
* for some adapter tunables, take PHYs out of reset, and initialize the MDIO
* interface.
*/
-int __devinit t3_prep_adapter(struct adapter *adapter,
- const struct adapter_info *ai, int reset)
+int t3_prep_adapter(struct adapter *adapter, const struct adapter_info *ai,
+ int reset)
{
int ret;
- unsigned int i, j = 0;
+ unsigned int i, j = -1;
get_pci_mode(adapter, &adapter->params.pci);
adapter->params.info = ai;
- adapter->params.nports = ai->nports;
+ adapter->params.nports = ai->nports0 + ai->nports1;
+ adapter->params.chan_map = (!!ai->nports0) | (!!ai->nports1 << 1);
adapter->params.rev = t3_read_reg(adapter, A_PL_REV);
- adapter->params.linkpoll_period = 0;
+ /*
+ * We used to only run the "adapter check task" once a second if
+ * we had PHYs which didn't support interrupts (we would check
+ * their link status once a second). Now we check other conditions
+ * in that routine which could potentially impose a very high
+ * interrupt load on the system. As such, we now always scan the
+ * adapter state once a second ...
+ */
+ adapter->params.linkpoll_period = 10;
adapter->params.stats_update_period = is_10G(adapter) ?
MAC_STATS_ACCUM_SECS : (MAC_STATS_ACCUM_SECS * 10);
adapter->params.pci.vpd_cap_addr =
mc7_prep(adapter, &adapter->pmtx, MC7_PMTX_BASE_ADDR, "PMTX");
mc7_prep(adapter, &adapter->cm, MC7_CM_BASE_ADDR, "CM");
- p->nchan = ai->nports;
+ p->nchan = adapter->params.chan_map == 3 ? 2 : 1;
p->pmrx_size = t3_mc7_size(&adapter->pmrx);
p->pmtx_size = t3_mc7_size(&adapter->pmtx);
p->cm_size = t3_mc7_size(&adapter->cm);
}
early_hw_init(adapter, ai);
+ ret = init_parity(adapter);
+ if (ret)
+ return ret;
for_each_port(adapter, i) {
u8 hw_addr[6];
+ const struct port_type_info *pti;
struct port_info *p = adap2pinfo(adapter, i);
- while (!adapter->params.vpd.port_type[j])
- ++j;
+ while (!adapter->params.vpd.port_type[++j])
+ ;
- p->port_type = &port_types[adapter->params.vpd.port_type[j]];
- p->port_type->phy_prep(&p->phy, adapter, ai->phy_base_addr + j,
- ai->mdio_ops);
+ pti = &port_types[adapter->params.vpd.port_type[j]];
+ if (!pti->phy_prep) {
+ CH_ALERT(adapter, "Invalid port type index %d\n",
+ adapter->params.vpd.port_type[j]);
+ return -EINVAL;
+ }
+
+ p->phy.mdio.dev = adapter->port[i];
+ ret = pti->phy_prep(&p->phy, adapter, ai->phy_base_addr + j,
+ ai->mdio_ops);
+ if (ret)
+ return ret;
mac_prep(&p->mac, adapter, j);
- ++j;
/*
* The VPD EEPROM stores the base Ethernet address for the
ETH_ALEN);
memcpy(adapter->port[i]->perm_addr, hw_addr,
ETH_ALEN);
- init_link_config(&p->link_config, p->port_type->caps);
+ init_link_config(&p->link_config, p->phy.caps);
p->phy.ops->power_down(&p->phy, 1);
- if (!(p->port_type->caps & SUPPORTED_IRQ))
+
+ /*
+ * If the PHY doesn't support interrupts for link status
+ * changes, schedule a scan of the adapter links at least
+ * once a second.
+ */
+ if (!(p->phy.caps & SUPPORTED_IRQ) &&
+ adapter->params.linkpoll_period > 10)
adapter->params.linkpoll_period = 10;
}
t3_set_reg_field(adapter, A_T3DBG_GPIO_EN, F_GPIO0_OUT_VAL,
F_GPIO0_OUT_VAL);
}
+
+int t3_replay_prep_adapter(struct adapter *adapter)
+{
+ const struct adapter_info *ai = adapter->params.info;
+ unsigned int i, j = -1;
+ int ret;
+
+ early_hw_init(adapter, ai);
+ ret = init_parity(adapter);
+ if (ret)
+ return ret;
+
+ for_each_port(adapter, i) {
+ const struct port_type_info *pti;
+ struct port_info *p = adap2pinfo(adapter, i);
+
+ while (!adapter->params.vpd.port_type[++j])
+ ;
+
+ pti = &port_types[adapter->params.vpd.port_type[j]];
+ ret = pti->phy_prep(&p->phy, adapter, p->phy.mdio.prtad, NULL);
+ if (ret)
+ return ret;
+ p->phy.ops->power_down(&p->phy, 1);
+ }
+
+return 0;
+}
+
projects / linux-flexiantxendom0-natty.git / blobdiff