- 2.6.17 port work build breaks, but the patch set is relativly stable

[linux-flexiantxendom0-3.2.10.git] / drivers / net / ne.c

diff --git a/drivers/net/ne.c b/drivers/net/ne.c
index 94f782d..b327652 100644 (file)
--- a/drivers/net/ne.c
+++ b/drivers/net/ne.c
@@ -50,6 +50,7 @@ static const char version2[] =
 #include <linux/delay.h>
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
+#include <linux/jiffies.h>
 
 #include <asm/system.h>
 #include <asm/io.h>
@@ -138,8 +139,9 @@ bad_clone_list[] __initdata = {
 
 #if defined(CONFIG_PLAT_MAPPI)
 #  define DCR_VAL 0x4b
-#elif defined(CONFIG_PLAT_OAKS32R)
-#  define DCR_VAL 0x48
+#elif defined(CONFIG_PLAT_OAKS32R)  || \
+   defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938)
+#  define DCR_VAL 0x48         /* 8-bit mode */
 #else
 #  define DCR_VAL 0x49
 #endif
@@ -225,7 +227,7 @@ struct net_device * __init ne_probe(int unit)
        netdev_boot_setup_check(dev);
 
 #ifdef CONFIG_TOSHIBA_RBTX4938
-       dev->base_addr = 0x07f20280;
+       dev->base_addr = RBTX4938_RTL_8019_BASE;
        dev->irq = RBTX4938_RTL_8019_IRQ;
 #endif
        err = do_ne_probe(dev);
@@ -341,7 +343,7 @@ static int __init ne_probe1(struct net_device *dev, int ioaddr)
                outb(inb(ioaddr + NE_RESET), ioaddr + NE_RESET);
 
                while ((inb_p(ioaddr + EN0_ISR) & ENISR_RESET) == 0)
-               if (jiffies - reset_start_time > 2*HZ/100) {
+               if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
                        if (bad_card) {
                                printk(" (warning: no reset ack)");
                                break;
@@ -395,10 +397,22 @@ static int __init ne_probe1(struct net_device *dev, int ioaddr)
                /* We must set the 8390 for word mode. */
                outb_p(DCR_VAL, ioaddr + EN0_DCFG);
                start_page = NESM_START_PG;
-               stop_page = NESM_STOP_PG;
+
+               /*
+                * Realtek RTL8019AS datasheet says that the PSTOP register
+                * shouldn't exceed 0x60 in 8-bit mode.
+                * This chip can be identified by reading the signature from
+                * the  remote byte count registers (otherwise write-only)...
+                */
+               if ((DCR_VAL & 0x01) == 0 &&            /* 8-bit mode */
+                   inb(ioaddr + EN0_RCNTLO) == 0x50 &&
+                   inb(ioaddr + EN0_RCNTHI) == 0x70)
+                       stop_page = 0x60;
+               else
+                       stop_page = NESM_STOP_PG;
        } else {
                start_page = NE1SM_START_PG;
-               stop_page = NE1SM_STOP_PG;
+               stop_page  = NE1SM_STOP_PG;
        }
 
 #if  defined(CONFIG_PLAT_MAPPI) || defined(CONFIG_PLAT_OAKS32R)
@@ -508,15 +522,9 @@ static int __init ne_probe1(struct net_device *dev, int ioaddr)
        ei_status.name = name;
        ei_status.tx_start_page = start_page;
        ei_status.stop_page = stop_page;
-#if defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938)
-       wordlength = 1;
-#endif
 
-#ifdef CONFIG_PLAT_OAKS32R
-       ei_status.word16 = 0;
-#else
-       ei_status.word16 = (wordlength == 2);
-#endif
+       /* Use 16-bit mode only if this wasn't overridden by DCR_VAL */
+       ei_status.word16 = (wordlength == 2 && (DCR_VAL & 0x01));
 
        ei_status.rx_start_page = start_page + TX_PAGES;
 #ifdef PACKETBUF_MEMSIZE
@@ -580,7 +588,7 @@ static void ne_reset_8390(struct net_device *dev)
 
        /* This check _should_not_ be necessary, omit eventually. */
        while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0)
-               if (jiffies - reset_start_time > 2*HZ/100) {
+               if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
                        printk(KERN_WARNING "%s: ne_reset_8390() did not complete.\n", dev->name);
                        break;
                }
@@ -787,7 +795,7 @@ retry:
 #endif
 
        while ((inb_p(nic_base + EN0_ISR) & ENISR_RDC) == 0)
-               if (jiffies - dma_start > 2*HZ/100) {           /* 20ms */
+               if (time_after(jiffies, dma_start + 2*HZ/100)) {                /* 20ms */
                        printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
                        ne_reset_8390(dev);
                        NS8390_init(dev,1);